Specifications - Sony LMD-2451W Operating Instructions Manual

Specifications

Picture performance
LCD panel a-Si TFT Active Matrix
Pixel efficiency 99.99%
Viewing angle (up/down/left/right, contrast > 10:1)
89°/89°/89°/89° (typical)
Scan Normal 0%
Over scan 5%
Efficient picture size
518.4 × 324.0, 613.2 mm (w/h, dia)
1
(20 /
2
Resolution H 1,920 dots, V 1,200 lines
Aspect ratio 16:10
Input
Composite input (NTSC/PAL) connector
BNC type (1)
1 Vp-p ± 3 dB sync negative
Y/C input connector
4-pin mini-DIN (1)
Y: 1 Vp-p ± 3 dB sync negative
C: 0.286 Vp-p ± 3 dB (NTSC burst
signal level)
0.3 Vp-p ± 3 dB (PAL burst signal
level)
RGB/component input connectors
BNC type (3)
RGB input: 0.7 Vp-p ± 3 dB (Sync On
Green, 0.3 Vp-p sync negative)
Component input: 0.7 Vp-p ± 3 dB
(75% chrominance standard color
bar signal)
Audio input connectors
Phono jack (2)
–5 dBu 47 kilohms or higher
External synchronized input connector
BNC type (1)
0.3 to 4.0 V p-p ± bipolarity ternary or
negative polarity binary
HD15 input connector
D-sub 15-pin (1)
R/G/B: 0.7 Vp-p, sync positive (Sync
On Green, 0.3 Vp-p sync negative)
Sync: TTL level (polarity free, H/V
separate sync)
Plug & Play function: corresponds to
DDC2B
DVI input connector
DVI-D (1)
TMDS single link
Remote input connector
Parallel remote
Modular connector 8-pin (1)
Serial remote
32
Specifications
7
× 12 / , 24 inches)
8
D-sub 9-pin (RS-232C) (1)
RJ-45 modular connector
(ETHERNET) (1)
Optional input slot
2 slots
Signal format:
H: 15 kHz to 45 kHz
V: 48 Hz to 60 Hz
DC IN connector
DC 24 V (output impedance 0.05 Ω or
less)
Output
Composite output connector
BNC type (1)
Loop-through, with 75 ohms automatic
terminal function
Y/C output connector
4-pin mini-DIN (1)
Loop-through, with 75 ohms automatic
terminal function
RGB/component connectors
BNC type (3)
Loop-through, with 75 ohms automatic
terminal function
External synchronized output connector
BNC type (1)
Loop-through, with 75 ohms automatic
terminal function
Audio monitor output connectors
Phono jack (2)
Built-in speaker output
1.0 W + 1.0 W (stereo)
General
Power AC 100 V to 240 V, 50/60 Hz, 1.5 A to
0.7 A
DC 24 V, 5.7 A
Power consumption
Maximum: approx. 130 W (when two
BKM-229X are installed)
Peak inrush current
(1) Power ON, current probe method:
23 A (100 V), 56 A (240 V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1:
55 A (230 V)
Dimensions Approx. 602.4 × 497.9 × 269.9 mm
(including the projection parts)
3
(23 / × 19
4
(w/h/d)
Mass Approx. 11.0 kg (24 lb 4 oz) (when no
input adaptor is installed)
Approx. 11.4 kg (25 lb 2 oz) (when two
BKM-229X are installed)
Operating conditions
5 3
/ × 10 / inches)
8 4