Related Manuals for Shure MX202W-A/C
Summary of Contents for Shure MX202W-A/C
- Page 1 MX200 Series Overhead Microphones Online user guide for Shure Microflex MX200 Series overhead microphones. Version: 6 (2020-B)
-
Page 2: Table Of Contents
Shure Incorporated Table of Contents Permanent Installation MX200 SeriesOverhead Microphones Installing the In-Line Preamp Ceiling Tile Installation General Description Plate Mount Preamp Installation Model Variations Specifications Interchangeable Cartridges Furnished Accessories Snap-Fit Windscreen Replacement Parts Preamp Gain Wiring Diagram RFI Filtering... -
Page 3: Mx200 Seriesoverhead Microphones
General Description ® Shure Microflex MX200 Series microphones are miniature electret condenser microphones designed for miking choirs and performance groups. They are typically suspended over the heads of the performers. Their high sensitivity and wide frequency range make them suitable for recording, as well as sound reinforcement applications. An attached 101 mm (4 in.) gooseneck allows them to be easily aimed at the sound source. -
Page 4: Snap-Fit Windscreen
Provides 30 dB of "pop" protection. Preamp Gain If necessary, the preamplifier gain can be reduced by 12 dB. Contact an authorized Shure service center for information. RFI Filtering Important: Microphones must be used with the RK100PK or RK202PK plate-mounted preamp to optimize RF immunity. - Page 5 Shure Incorporated • If four or more microphones will be open at once, an automatic mixer, such as the Shure SCM810 or SCM410, is recom mended. Set up the automatic mixer so that all overhead microphones gate on simultaneously. 5/16...
-
Page 6: Permanent Installation
Shure Incorporated Permanent Installation Installing the In-Line Preamp Use the two supplied mounting clamps to hold the preamp in place on a wall or ceiling. 6/16... -
Page 7: Ceiling Tile Installation
Shure Incorporated Ceiling Tile Installation Drill a 1/2 in. hole into the ceiling tile. CAUTION: To avoid tile damage, use a 1/2 in. augur bit and drill very slowly. Unplug the mini 4-pin connector from the preamp and feed the cable through the hole. - Page 8 Shure Incorporated 8/16...
-
Page 9: Plate Mount Preamp Installation
Shure Incorporated Plate Mount Preamp Installation The plate-mounted preamp allows you to mount the preamp in an electical box and use conduit to run cable through ceilings and walls. Remove preamp housing by removing two phillips head screws. Remove knock-out from the hole in the center of the cover plate (if present). -
Page 10: Specifications
Shure Incorporated Specifications Type Electret Condenser Frequency Response 50–17000 Hz 10/16... - Page 11 Shure Incorporated Polar Pattern MX202B/C Cardioid MX202B/S Supercardioid MX202B/MS Mini-shotgun Output Impedance 180 Ω Output Configuration Active Balanced Sensitivity @ 1 kHz, open circuit voltage Cardioid −35 dBV/Pa (18 mV) Supercardioid −34 dBV/Pa (21 mV) Mini-shotgun -33 dBV/Pa (22 mV)
-
Page 12: Furnished Accessories
Shure Incorporated 45 dB, minimum Clipping Level at 1% THD −6 dBV (0.5 V) Polarity Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector Environmental Conditions Operating Temperature –18–57°C (0–135°F) Storage Temperature –29–74°C (–20–165°F) -
Page 13: Wiring Diagram
Shure Incorporated Wiring Diagram 13/16... - Page 14 Shure Incorporated 14/16...
- Page 15 Shure Incorporated 15/16...
-
Page 16: Certifications
Shure Incorporated 16/16...