Table of Contents

Advertisement

Quick Links

Topaz 85s
Use and maintenance
Warning! Please read the instructions before use.
ADIATEK srl
Head Office:
Via Monte Pastello, 14
I-37057 San Giovanni Lupatoto (VR)
www.adiatek.com - info@adiatek.com
07 2020
Tel.
+39 045 877 9086
Fax.
+39 045 877 9195

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Topaz 85s and is the answer not in the manual?

Questions and answers

Summary of Contents for ADIATEK Topaz 85s

  • Page 1 Topaz 85s 07 2020 Use and maintenance Warning! Please read the instructions before use. ADIATEK srl Head Office: Via Monte Pastello, 14 Tel. +39 045 877 9086 I-37057 San Giovanni Lupatoto (VR) Fax. +39 045 877 9195 www.adiatek.com - info@adiatek.com...
  • Page 3: Table Of Contents

    INTRODUCTORY COMMENT Thank you for having chosen our machine. This floor cleaning machine is meant for a commercial use and is used for the industrial and civil cleaning for any type of floor application. During its advance movement, the combined action of the brushes and the detergent solution removes the dirt which is aspirated through the rear suction assembly, giving a perfectly dry surface.
  • Page 4: General Rules Of Safety

    GENERAL RULES OF SAFETY − Do not wash the machine with direct water jets or with high water pressure nor with corrosive material. − Every 200 working hours have a machine check by an authorized The rules below have to be followed carefully in order to avoid injury to the operator and damage to the machine.
  • Page 5: Technical Description

    TECHNICAL DESCRIPTION Cleaning width Squeegee width 1175 Working capacity, up to 6375 Brushes diameter 2 x 150 Brushes rpm Pressure on the brushes (max) Brushes motor 2 x 650 Traction motor 1200 Suction motor 2 x 570 Suction vacuum mbar Type of drive automatic Movement speed (max)
  • Page 6: Steering Wheel Panel

    STEERING WHEEL PANEL DISPLAY UP/DOWN BRUSHES BUTTON ON/OFF SUCTION MOTOR/ SILENCE MODE BUTTON UP/DOWN SQUEEGEE BUTTON MODE SELECTOR BUTTON • AUTOMATIC • MANUAL • BREAK WASHING MODE BUTTON (WATERWORKS SELECTION) DETERGENT SOLUTION LEVEL BUTTON MAXIMUM SPEED INCREASE BUTTON MAXIMUM SPEED DECREASE BUTTON CONTROLS BOARD LEGEND 10.
  • Page 7: Display Reading

    DISPLAY READING DISPLAY WHILE SWITCHING ON When the machine is switched on, the display shows the following screen. Next screen will be displayed as follows: BATTERY SETTINGS SOFTWARE RELEASE Gel batteries settings HOUR METER Display card software AGM batteries settings release Lead/acid batteries Chopper card software...
  • Page 8 After selecting the 3S or the 3SD mode (see the 3S/3SD mode paragraph), the display will show the following controls: 3S mode 3SD mode Solenoid valve Solenoid valve on Detergent percentage Solenoid valve Solenoid valve off Water flow Water flow level level After selecting the Ozone mode (see Ozone mode selection chapter), the If the machine is equipped with the Ozone system and an optional...
  • Page 9: Navigation Controls

    NAVIGATION CONTROLS Scroll UP Increase Enter Scroll Decrease DOWN GENERAL SETTINGS To enter the general settings menu, use the controls panel as follows: Keep the buttons (1) and (4) pressed simultaneously. Turn the key on. When "INSERT PASSWORD:0" is displayed, press the ENTER button (3).
  • Page 10: Manual Symbology

    MANUAL SYMBOLOGY Icon denoting the open book. Obligation symbol requiring the wear of Indicates that the operator has to read the protection glasses. manual before the use of the machine. Warning lcon. Read carefully the sections marked with this Obligation symbol requiring the wear of symbol, for the security of both the operator protection gloves.
  • Page 11: Optionals

    OPTIONALS Optionals support 3SD System (Solution Saving System Dispenser) Ozone system O3...
  • Page 12: Before Use

    BEFORE USE HANDLING OF THE PACKED MACHINE The machine is supplied with suitable packing foreseen for fork lift truck handling. For the package dimensions please look at the “TECHNICAL DESCRIPTION” table. Do not place more than 2 packagins on top of each other. UNPACKING THE MACHINE Remove the external packing.
  • Page 13: Batteries Charge Level Indicator

    SQUEEGEE ASSEMBLY 2. Connect the terminals, respecting the polarities, avoiding 1. Insert the two stud bolts (2) situated on the upper part of the contact with other parts that could create short circuit. squeegee (3) inside the slots present on the support (1). 2.
  • Page 14: Assembling And Disassembling The Splash Guards

    ASSEMBLING AND DISASSEMBLING THE SPLASH GUARDS Check that the machine is on manual mode, if not, press button (2) and on the display the according icon will be shown. For the splash guards cleaning, it is necessary to take off the two metal covers.
  • Page 15: Adjusting The Footboard

    To increase or decrease the lever locking strength, turn ferrule. ADJUSTING THE FOOTBOARD Using the knob (1) it is possible to adjust the height of the footboard. ADJUSTING THE SEAT Using the lever (1) it is possible to adjust the seat position.
  • Page 16: Floor Cleaning

    FLOOR CLEANING Screw the solution tank cap. CONNECTING THE BATTERY CONNECTOR AND SWITCHING ON THE MACHINE Once that the battery recharging has been completed: Disconnect the connector (2) of the battery recharger from the Use always low foam detergent. battery connector (1). Protect yourself from accidental contact or splashes with the Connect then the battery connector (1) to the machine protection devices provided by the detergent manufacturer.
  • Page 17: Brushes Pressure Adjustment

    SPEED ADJUSTMENT, FORWARD AND BACKWARD Before running the machine select the maximum speed level during work. Press buttons (+) and (-) to see the speed level on the display. Adjust the detergent solution flow rate by using the selector (3). Lower the brushes base on the floor pressing button (4);...
  • Page 18: Standard Mode - 3S

    STANDARD MODE - 3S After a couple of seconds, the symbol will stop blinking and the mode The detergent solution flow rate is always adjusted using an 8-way will be selected. manipulator (see chapter “FLOW RATE SELECTION”). INSTALLATION DETERGENT TANK (MODE 3SD) When in standard mode the detergent solution flow is constant, related to the number selected with the manipulator.
  • Page 19: Combining The Ozone System With The 3S And 3Sd Systems

    HORN The machine is provided with a horn that can be activated pressing button (1). EMERGENCY BUTTON In case of emergency press When the O3 icon stops blinking button placed the system is being selected. dashboard. All the functions and movement will immediately disabled.
  • Page 20 When this happens, it is necessary to drain the recovery tank (see chapter “DRAINING AND CLEANING THE RECOVERY TANK”).
  • Page 21: Stop Of The Machine After Cleaning Operation

    STOP OF THE MACHINE AFTER CLEANING OPERATION BREAK WASHING MODE IN AUTOMATIC OR MANUAL WORKING MODE: At the end of the washing cycle, keeping the button (1) pressed, the functioning of BREAK WASHING is activated. When the signal lamp (2) is on, then the machine BREAK WASHING mode.
  • Page 22: Cleaning The Brushes

    Lower the brushes base by pressing button (3). Turn the key switch counterclockwise to turn off the machine. Unlock the side rubber bar after having removed the knob (4). Open the side rubber bar (5) as per figure. CLEANING THE BRUSHES Take off the brushes to clean them with a water jet (to read how to do it see chapter “ASSEMBLING AND DISASSEMBLIMG THE BRUSHES”).
  • Page 23: Weekly Maintenance

    WEEKLY MAINTENANCE REAR SQUEEGEE RUBBER CHECK Close detergent solution flow valve (1) Check the squeegee rubber wearing and eventually turn it or replace To replace the rubber, it is necessary to: Lift up the squeegee (see under “STOP OF THE MACHINE AFTER Unscrew the filter (2) cap.
  • Page 24: Six-Monthly Maintenance

    SIX-MONTHLY MAINTENANCE THE TRACTION MOTOR DOES NOT WORK Properly sit on the driving seat. SPLASH GUARD RUBBER CHECK Check that the emergency system (1) is not activated. With the brushes assembled, the splash guards must slightly touch the floor. If they are worn, they have to be replaced. To do the replacement contact the licensed technical assistance center.
  • Page 25: The Squeegee Does Not Dry Perfectly

    To replace the brushes, see instructions under paragraph “ASSEMBLING AND DISASSEMBLING THE BRUSHES” The detergent solution is not sufficient: increase the water carriage valve (see under paragraph “FLOW RATE SELECTION”). Check that the liquid detergent is in the recommended percentage. Increase the brushes base pressure (see under paragraph "ADJUSTMENT OF THE BRUSHES PRESSURE").
  • Page 26: Programmed Maintenance

    PROGRAMMED MAINTENANCE PERIODIC ORDINARY MAINTENANCE CHART DAILY PERIODIC INTERVENTION • RECOVERY TANK CLEANING • SUCTION FILTER CLEANING • SOLUTION TANK FILTER CLEANING • BRUSHES CLEANING • BRUSHES DISASSEMBLY AND CLEANING • SQUEEGEE CLEANING • FRONT SQUEEGEE RUBBER CHECK • REAR SQUEEGEE RUBBER CHECK •...

Table of Contents