Subscribe to Our Youtube Channel
Related Manuals for ADIATEK Topaz 90
Summary of Contents for ADIATEK Topaz 90
- Page 1 Topaz 90 01 2019 Use and maintenance Warning! Please read the instructions before use.
-
Page 3: Table Of Contents
INTRODUCTORY COMMENT Thank you for having chosen our machine. This floor cleaning machine is used for the industrial and civil cleaning and is able to clean any type of floor. During its advance movement, the combined action of the brushes and the detergent solution removes the dirt which is aspirated through the rear suction assembly, giving a perfectly dry surface. -
Page 4: General Rules Of Safety
GENERAL RULES OF SAFETY − Before using the machine, check that all panels and coverings are in their position as indicated in this use and maintenance The rules below have to be followed carefully in order to avoid injury catalogue. to the operator and damage to the machine. -
Page 5: Technical Description
TECHNICAL DESCRIPTION Cleaning width Squeegee width 1175 Working capacity, up to 6750 Brushes diameter 2 x 460 Brushes rpm Pressure on the brushes Brushes motor 2 x 700 Traction motor 1200 Suction motor 2 x 570 Suction vacuum mbar Type of drive automatic Movement speed (max) km/h... -
Page 6: Steering Wheel Panel
STEERING WHEEL PANEL DISPLAY UP/DOWN BRUSHES BUTTON ON/OFF SUCTION MOTOR BUTTON UP/DOWN SQUEEGEE BUTTON MODE SELECTOR BUTTON • AUTOMATIC • MANUAL • BREAK WASHING MODE BUTTON (WATERWORKS SELECTION) DETERGENT SOLUTION LEVEL BUTTON MAXIMUM SPEED INCREASE BUTTON MAXIMUM SPEED DECREASE BUTTON CONTROLS BOARD LEGEND 10. -
Page 7: Display Reading
DISPLAY READING DISPLAY WHILE SWITCHING ON When the machine is switched on, the display shows the following screen. Next screen will be displayed as follows: BATTERY SETTINGS SOFTWARE RELEASE Gel batteries settings HOUR METER Display card software AGM batteries settings release Lead/acid batteries Chopper card software... -
Page 8: Manual Symbology
MANUAL SYMBOLOGY Icon denoting the open book. Obligation symbol requiring the wear of Indicates that the operator has to read the protection glasses. manual before the use of the machine. Icon denoting the open book. Obligation symbol requiring the wear of For the good functioning of the battery protection gloves. -
Page 9: Before Use
BEFORE USE HANDLING OF THE PACKED MACHINE The machine is supplied with suitable packing foreseen for fork lift truck handling. For the package dimensions please look at the “TECHNICAL DESCRIPTION” table. Do not place more than 2 packagins on top of each other. UNPACKING THE MACHINE Remove the external packing. -
Page 10: Batteries Charge Level Indicator
3. Insert the squeegee hose (4) into its coupling, respecting its 2. Connect the terminals, respecting the polarities, avoiding position as indicated in the figure. contact with other parts that could create short circuit. ADJUSTING THE SQUEEGEE In order to have a perfect drying result through the squeegee, the rear rubber must have the lower bending uniformly adjusted in all its length. -
Page 11: Adjusting The Splash Guards
To assemble the covers, it is necessary to proceed as follows: 1. Take off the clips (1) present on the pins (2) fixed to the brushes base. 2. Take off the cover from the brushes base. For the assembly it is necessary to proceed inversely with above- mentioned operation. -
Page 12: Adjusting The Seat
ADJUSTING THE SEAT Using the lever (1) it is possible to adjust the seat position. -
Page 13: Floor Cleaning
FLOOR CLEANING Screw the solution tank cap. CONNECTING THE BATTERY CONNECTOR AND SWITCHING ON THE MACHINE Once that the battery recharging has been completed: Disconnect the connector (2) of the battery recharger from the Use always low foam detergent. To avoid foam presence, before battery connector (1). -
Page 14: Brushes Pressure Adjustment
Adjust the detergent solution flow rate by using the selector (3). To move the machine, select the direction using the lever (1) placed on the dashboard. Lower the brushes base on the floor pressing button (4); the display will show first the lifting down symbol and then the brushes on symbol. -
Page 15: Selection Mode Standard - 3S
SELECTION MODE STANDARD - 3S To switch from a mode to Insert tank into another press the button (1) appropriate housing. once. On the display the related circuit symbol starts blinking (see chapter Remove the cap of the tank and “FLOW RATE SELECTION”). -
Page 16: Horn
the instrument board or press the drive pedal, the display will then turn on again and after a few seconds the machine returns operative. HORN The machine is provided with a horn that can be activated pressing button (1). EMERGENCY BUTTON When this happens, it is necessary to drain the recovery tank (see chapter “DRAINING AND CLEANING THE RECOVERY TANK”). -
Page 17: Stop Of The Machine After Cleaning Operation
STOP OF THE MACHINE AFTER CLEANING OPERATION BREAK WASHING MODE IN AUTOMATIC OR MANUAL WORKING MODE: At the end of the washing cycle, keeping the button (1) pressed, the functioning of BREAK WASHING is chosen. When the signal lamp (2) is on, then the machine BREAK WASHING mode. -
Page 18: Automatic Disassembly Of The Brushes
Unlock the hooks (1). Unscrew the wing nuts (2) to take off the outer rubber blades (3) and then the central one (4). Take off the rubber (5) to turn it or replace it. To reassemble the squeegee do these operations backwards. AUTOMATIC DISASSEMBLY OF THE BRUSHES With the brushes base lifted from... -
Page 19: Two-Monthly Maintenance
Never leave the batteries completely discharged for a long time. In case of alarm visualizations contact the technical assistance. Clean the solution tank with a water jet. If with the key switch positioned clockwise to switch on the machine the display and other functions are not activated, it is necessary to check the batteries' connection to the machine (see under paragraph Clean the filter components with a water jet “CONNECTION BATTERIES' CONNECTION AND SWITCHING ON OF THE... -
Page 20: The Traction Motor Does Not Work
If the problem persists, please contact the authorized technical Check that the liquid detergent is in the recommended assistance. percentage. Increase the brushes base pressure (see under paragraph THE TRACTION MOTOR DOES NOT WORK "ADJUSTMENT OF THE BRUSHES PRESSURE"). Step on the footboard. Contact the authorized technical assistance for advice. -
Page 21: Programmed Maintenance
PROGRAMMED MAINTENANCE PERIODIC ORDINARY MAINTENANCE CHART DAILY PERIODIC INTERVENTION • RECOVERY TANK CLEANING • SUCTION FILTER CLEANING • SOLUTION TANK FILTER CLEANING • BRUSHES CLEANING • BRUSHES DISASSEMBLY AND CLEANING • SQUEEGEE CLEANING • FRONT SQUEEGEE RUBBER CHECK • REAR SQUEEGEE RUBBER CHECK •...
Need help?
Do you have a question about the Topaz 90 and is the answer not in the manual?
Questions and answers