All the pictograms attached to the machine are Only use blades or accessories which have been shown and explained in this manual. approved by STIHL for this machine or which are technically equivalent. If you have any questions about this, consult your dealer.
Page 3
Never attempt to modify your power tool in any way since this may increase the risk of personal injury. STIHL excludes all liability for personal injury and damage to property caused while using unauthorized attachments. Do not use a high-pressure washer to clean the power tool.
Page 4
English 3 Safety Precautions and Working Techniques The power tool must only be operated when it is in good operating condition – Risk of accident! 15m (50ft) To prepare for emergencies when using a har‐ ness: Practice setting down the machine quickly. To avoid damage, do not throw the unit to the ground when practicing.
Page 5
Have all other work performed by a doubt, contact a dealer. servicing dealer. Examine the blade periodically at short intervals STIHL recommends that you have servicing and and as soon as you note any noticeable repair work carried out exclusively by an author‐ changes: ized STIHL servicing dealer.
STIHL recommends you use only original STIHL cutting blades – see "Special Accessories". Only use deflectors or accessories that are explicity approved for this power tool by STIHL or are technically identical. Using the Unit ► Shut down the engine.
Page 7
4 Using the Unit English 4.2.1 Adjust correctly WARNING The depth of cut depends on the unevenness of the ground, your height and the way you hold the Do not adjust the deflector. edger. Use the following procedure: ► Adjust the depth wheel (2) so that the The deflector has been set at the factory so that blade (3) just touches the ground or breaks the arrow on the deflector and the open side...
The KombiTool can also be mounted on STIHL brushcutters with a split shaft (T-models) (basic power tools). When using the FCS-KM together with the KM 94 R, the rigid shaft in the FCS-KM must be replaced by a flexible shaft. 0458-472-0121-E...
6 Assembling the Unit English This KombiTool can therefore also be used on If the FCS-KM KombiTool is used with a KM 94 the following machine: R KombiMotor, its rigid shaft must be removed and the flexible shaft installed in its place. The STIHL FR 130 T flexible shaft is not included with the machine.
English 7 Mounting the KombiTool Removing the KombiTool ► Push the drive tube (3) through the clamp and into the gearbox – turn the gearbox back and ► Reverse the above sequence to remove the forth as necessary. drive tube. ►...
9 Starting / Stopping the Engine English ► Place the machine on the ground in a secure position The blade must not touch the ground or any other objects – risk of accident! ► Assume a firm stance – possibilities: standing, bending or kneeling ►...
► Pull the skirt (3) out of the segment (6) and out Have a worn depth wheel replaced by a servicing of the gap (5) in the deflector dealer. STIHL recommends that you have servic‐ 12.2 Fitting the skirt ing and repair work carried out exclusively by an authorized STIHL servicing dealer.
14 Checking and Replacing the Wear Guard English STIHL recommends you use only the following NOTICE original STIHL cutting blades: Length Thickness Marking The gearbox may be seriously damaged if you 200 mm 2.4 mm 4133 / 01 do not replace the wear guard in good time.
1 Blade be performed by a servicing dealer. 2 Deflector STIHL recommends that you have servicing and 3 Drive tube repair work carried out exclusively by an author‐ ized STIHL servicing dealer. STIHL dealers are...
KM 56 R with loop 5.0 m/s 6.4 m/s Max. output shaft speed (cutting attachment) on handle: STIHL brushcutters with split shaft (T models): KM 85 R with loop 3.0 m/s 4.9 m/s handle: FR 130 T: 4900 rpm KM 90 R with loop 3.4 m/s...
EN ISO 12100 (in conjunction with the listed KM‑ When repairing the machine, only use replace‐ and FR‑ tools) ment parts which have been approved by STIHL EN ISO 12100, EN 60335-1, EN 50636-2-92 (in for this power tool or are technically identical.
Page 17
FR‑ tools) EN ISO 12100, EN 60335-1, EN 50636-2-92 (in conjunction with the specified KMA tools). Technical documents deposited at: ANDREAS STIHL AG & Co. KG The year of manufacture is indicated on the power tool. Waiblingen, 2022-08-01 ANDREAS STIHL AG & Co. KG Robert Olma, Vice President, Regulatory Affairs &...
Page 18
English 22 UKCA Declaration of Conformity 0458-472-0121-E...
Page 19
22 UKCA Declaration of Conformity English 0458-472-0121-E...
Need help?
Do you have a question about the FCS-KM and is the answer not in the manual?
Questions and answers