Stihl FCS-KM Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Lawn Mower
  5. FCS-KM
  6. Instruction manual

Stihl FCS-KM Instruction Manual

Hide thumbs Also See for FCS-KM:
Table of Contents

Advertisement

Quick Links

Download this manual
STIHL FCS-KM
Instruction Manual

Advertisement

Table of Contents
loading

Related Manuals for Stihl FCS-KM

Summary of Contents for Stihl FCS-KM

  • Page 1 STIHL FCS-KM Instruction Manual...

  • Page 3: Table Of Contents

    English Contents Dear Customer, KombiSystem Guide to Using this Manual Thank you for choosing a quality engineered STIHL product. Safety Precautions and Working Techniques It has been built using modern Using the Unit production techniques and comprehensive quality assurance. Approved KombiEngines...

  • Page 4: Kombisystem

    English KombiSystem Guide to Using this Manual Safety Precautions and Working Techniques In the STIHL KombiSystem a number of Special safety precau- Pictograms different KombiEngines and KombiTools tions must be observed can be combined to produce a power when working with this tool.
  • Page 5 English STIHL recommends the use of genuine Transporting the Power Tool Wear steel-toed safety STIHL tools and accessories. They are boots with non-slip soles. specifically designed to match the product and meet your performance requirements. The deflector on this power edger...
  • Page 6 Make sure you always have good gear housing. 15m (50ft) balance and secure footing. Take special care in slippery conditions Always hold the power tool firmly with (ice, wet ground, snow) – on slopes or both hands on the handles. uneven ground. FCS-KM...
  • Page 7 Shut off the good. Stay alert so as not to endanger engine. others. After finishing work, clean dirt, soil and plant residue off the cutting attachment – wear gloves to reduce the risk of injury. FCS-KM...

  • Page 8: Using The Unit

    STIHL recommends you use only and damage to the machine. If you have around lawns and flower beds. It will cut original STIHL cutting blades – see any questions in this respect, consult a almost all types of grass, weeds and soft "Special Accessories".
  • Page 9 (B) by no more than 5 mm (0.2 in). WARNING Do not adjust the deflector. The deflector has been set at the factory so that the arrow on the deflector and the open side point away from the FCS-KM...

  • Page 10: Approved Kombiengines

    This KombiTool may be operated only in combination with the following KombiEngines: STIHL KM 55 R, KM 56 R, KM 85 R, KM 90, KM 90 R, KM 94 R , KM 100, KM 100 R, KM 110, KM 110 R, KM 130,...

  • Page 11: Assembling The Unit

    Push the flexible shaft into the drive tube. The drive shaft must not project from the If the FCS-KM KombiTool is used with a Pull the protective caps off the ends tube more than 22 mm (L). KM 94 R KombiMotor, its rigid shaft...

  • Page 12: Mounting The Kombitool

    Tighten down the star knob (4) firmly. Removing the KombiTool Reverse the above sequence to Insert the stop pin (2) into the remove the drive tube. hole (3) as far as stop – apply slight pressure and turn back and forth FCS-KM...

  • Page 13: Starting / Stopping The Engine

    (11) and block the shaft. not touch the control elements on Fit the screw (6) in the shaft the control handle while doing so – counterclockwise and tighten it see instruction manual for the down firmly. KombiEngine or basic power tool FCS-KM...

  • Page 14: Storing The Machine

    Replacing the Skirt For periods of 3 months or longer Have a worn depth wheel replaced by a Removing the skirt servicing dealer. STIHL recommends Remove, clean and inspect the that you have servicing and repair work cutting blade. carried out exclusively by an authorized If the KombiTool is removed from STIHL servicing dealer.

  • Page 15: Replacing The Cutting Blade

    – it may break – it must be replaced – see "Mounting the Cutting Blade". Check the wear guard (1) for damage before starting the power STIHL recommends you use only the tool. following original STIHL cutting blades: The wear guard must be replaced Length...

  • Page 16: Maintenance And Care

    Replace if damaged – see "Replacing the Skirt" Blade Visual inspection before starting work Check tightness before starting work Have checked for out-of-balance if necessary, replace if out-of-balance – see "Replacing the Cutting Blade" Replace if damaged – see "Replacing the Cutting Blade" FCS-KM...

  • Page 17: Minimize Wear And Avoid Damage

    English servicing dealer. STIHL dealers are Minimize Wear and Avoid regularly given the opportunity to attend Damage training courses and are supplied with the necessary technical information. Observing the instructions in this manual and the KombiEngine manual helps If these maintenance operations are not...

  • Page 18: Main Parts

    English Main Parts Blade Deflector Drive tube Depth wheel Wingnut Gearbox Wear guard Skirt FCS-KM...

  • Page 19: Specifications

    KM 90 R with loop handle: 101 dB(A) FR 130 T: 1.3 m/s 1.7 m/s Noise and vibration data measurements KM 100 R with loop on power tools with the FCS-KM Vibration level a to ISO 22867 hv,eq handle: 101 dB(A)

  • Page 20: Maintenance And Repairs

    K-factor in accordance approved by STIHL for this power tool or approved disposal site for environment- with Directive 2006/42/EC is 2.0 m/s are technically identical. Only use high- friendly recycling.

  • Page 21: Ec Declaration Of Conformity

    English Waiblingen, 15.07.2021 EC Declaration of Conformity UKCA Declaration of ANDREAS STIHL AG & Co. KG Conformity ANDREAS STIHL AG & Co. KG ANDREAS STIHL AG & Co. KG Badstr. 115 Badstr. 115 D-71336 Waiblingen D-71336 Waiblingen Germany Germany declare under our sole responsibility that...
  • Page 22 English Waiblingen, 15.07.2021 ANDREAS STIHL AG & Co. KG Dr. Jürgen Hoffmann Director Product Certification & Regulatory Affairs FCS-KM...
  • Page 24 0458-472-0121-D englisch www.stihl.com *04584720121D* 0458-472-0121-D...

Table of Contents