Advertisement
1st MENU
Displayed
(
Ù
Ú
scrolling with the
and the
buttons)
1st MENU
Displayed
(scrolling with the Ù and the Ú
buttons)
This Manual is applicable to Soft LED1 XL
ILT ITALY srl
Via Cancelliera, 10/a
00041 Albano Laziale (Rome) Italy
tel. +39 06-902901 fax +39 06-90231051
www.desisti.it
2nd MENU
Displayed
X
(after pressing the
that stands for ENTER )
2nd MENU
Displayed
(after pressing the X that stands for
ENTER)
Explanation of Each MENU FUNCTION
DMX ADDRESS
This Function is to SET the DMX address from 1 to 512 (Product is delivered with default settingof the DMX
address at 1)
Ù
Once the C001 is displayed, act on the
button to increase the address to the desired value.
Temporary push will increment the value by 1, if the button is kept pushed the increment on numbers is
getting fast.
Once the desired Address number is accomplished press X ("ENTER") to make it active
LOCAL DIMMING CONTROL
This Function is to LOCALLY DIM the LED INTENSITY from 0 to 100% (Product is delivered with default setting
of the DIMMER at 0).
The intensity goes in increments of 1/100% so the display will show 000% with the dimmer at 0% and FULL
with the dimmer at 100%.
Temporary push will increment the value by 1/100, if the button is kept pushed the increment on numbers is
getting fast.
Once the desired Lighting Level is accomplished and it is wanted to leave that level and go to other functions
of the MENU, press "ENTER".
LOCAL OR REMOTE CONTROL SETTINGS
The LED Fresnel has the facility to block the LOCAL DIMMING SETTING and maintain it when the POWER is
turned first OFF and than ON again.
This allows for the LIGHT to be TUNED and FOCUSED locally and its dimming level can be blocked, so that for
instance a system lighting a SET can be operated by a remote switch or simple brakers by TURNING POWER
ON.
The relevant menu to access this function is CTRL, to enter in this menu press X ("ENTER"), it is than possible
Ù
to select either DMX or AUTO by acting on the
or
machine is set to DMX as default.
•
In DMX mode: the Fixture accepts DMX control....if in this mode the local DIMMING CONTROL is SET
to a level the Light behaviour will follow the HTP (Highest Takes Precedence) modality, in other words
it will keep the local DIMMING setting until the DMX level of the specific channel will be higher, from
that level onwards the DMX level will take precedence. In this condition if the DMX connection is
removed, the light will keep the last level....until power is ON. It will reset and Start at 0after Power
OFF and ON again.
In AUTO mode: the light will ignore any DMX control. In this mode any local dimming setting will be
maintained and will be automatically recalled after power off, when turning the power on again.
Explanation of Each MENU FUNCTION
TEMPERATURE
This function Displays in real time the LED BAR Case temperature in °C.
When pressing Enter again you exit from the temperature display.
The steady state TEMPERATURE of the LED BAR reaches approx. 55°C after many hours of continuous
operation with an ambient temperature of 25-30°C.
The Thermal Handling of the LED is Automatically handled by the local electronics and the LED will operate
until the LED BAR temperature reaches 80°C, that anyway is still way within the prescribed maximum
nominal prescribed by the LED BAR manufacturer that is 105°C.
In case the LED BAR temperature reaches 80°C the unit will automatically turn off.
Even in extreme Ambient temperature conditions the LED BAR shall never reach the 80°C limit.
The above protection threshold is there to protect the LED BAR from stressed working conditions in case some
other failures or specially critical working conditions are causing an over-temperature.
CHANNEL SETTING (RESOLUTION & FUNCTION)
This Function is to set the DIMMING RESOLUTION either at 8 bits or at 16 bits.
Once CHAN is displayed, act on the Ù or Ú buttons to scroll through the following choises:
•
8D: 8 bits resolution (the display will show 8D and this is the default setting).
The Fixture utilises 1 DMX Circuit for the Light Dimming, which is the
BASE CIRCUIT set in the ADDRESS.
•
8DS: NOT ACTIVE (for future use):
The foreseen function for this setting is: 8 bits resolution and STROBE (the display will show 8DS).
The Fixture will utilise 2 DMX Circuits,
the BASE CIRCUIT set in the ADDRESS will be the LIGHT DIMMING
and the second circuit (BASE +1) will be the STROBE
Ú
button and than press X ("ENTER") again. The
Revised on June 2020
Advertisement
