Advertisement
Available languages
Available languages
EXAMPLE: PROGRAMMING A LINEAR RUNNING LIGHT EFFECT
1) Switch the programming mode on (press RECORD/SHIFT and buttons 1, 5, 6 and 8).
2) Set both MASTER slider controls to the maximum (A upwards, B downwards).
3) Select mode 1-24 single via the MODE SELECT button (the green LED lights up).
4) Push the control 1 to 10 (maximum) and press the RECORD/SHIFT button once.
5) Push the controls 1 to zero and 2 to maximum and press RECORD/SHIFT again
6) Push controls 2 to zero and 3 to maximum and press RECORD/SHIFT again.
7) Repeat these steps up to control 24.
8) Select a memory page (1 to 4) via the PAGE/REC CLEAR button.
9) Save the running light effect in this page by pressing one of the flash buttons in section PRESET B (1 to 12). Use e.g.
button number 1.
10) Leave the programming mode by pressing simultaneously the RECORD/SHIFT and REC EXIT buttons.
PLAYING A RUNNING LIGHT PATTERN
1) Select the mode CHASE/SCENES via the MODE SELECT button. The red LED lights up.
2) Push the control of the appropriate channel (memory) from section PRESET B to the top. In our example it was flash
button 1. This triggers the steps which are stored in that memory. If the appropriate slider control was already in the
upper position, it is necessary to pull it down first and push it up again to trigger the pattern.
ERASING A RUNNING LIGHT PATTERN
1) Activate the programming mode (press RECORD/SHIFT and buttons 1, 5, 6 and 8 –the top row).
2) Select the required page (1 to 4) via the PAGE/REC CLEAR button.
3) Hold the RECORD/SHIFT button down and press quickly TWICE the appropriate flash button from section PRESET B
in which the pattern to be erased is stored.
4) Release the RECORD/SHIFT. All indicator LEDs light up to confirm.
CHANGING A RUNNING LIGHT PATTERN
A running light pattern (scene) can contain up to 99 steps. These steps can be changed or erased later. You can also add
steps later. Each 'step' is a determined setting of the variable light intensity (0-100%) of 24 lamps or groups of lamps.
Erasing a particular step:
1)
Activate the programming mode (press RECORD/SHIFT and simultaneously 1, 5, 6, and 8).
2)
Select the required page via the PAGE button.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern (flash
buttons in the lower row of the section PRESET B).
5) Release the EDIT button and select via the STEP button the step to be erased.
6) Press the DELETE button and the selected step will be erased from the memory.
7) Leave the programming mode by holding the RECORD/SHIFT button down while pressing twice the REC/EXIT
button.
Adding steps:
1)
Activate the programming mode (press RECORD/SHIFT and simultaneously in sequence 1, 5, 6, and 8).
2)
Select the required page via the PAGE button.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern (flash
buttons in the lower row of the section PRESET B).
5)
Release the EDIT button and select via the STEP button the step just after the step to be added.
6)
Set the required light position via the slider controls, press the RECORD/SHIFT button and then the INSERT button.
7)
If required, repeat steps 5 and 6 to add more steps.
8)
Hold the RECORD/SHIFT button down and press twice the REC/EXIT button to leave the programming mode.
Changing steps:
1)
Activate the programming mode (press RECORD/SHIFT and simultaneously in sequence 1, 5, 6, and 8).
2)
Select the required page via the PAGE button.
3)
Press the MODE SELECT button until the red LED lights up (CHASE-SCENES).
4)
Hold the EDIT button down and press at the same time the flash button of the appropriate running light pattern (flash
buttons in the lower row of the section PRESET B).
5)
Select the required step via the STEP button.
6)
Now you can change the light intensity of the lamps as follows: hold the DOWN button pressed while pressing the flash
button of the channel that you want to change. The display shows which setting has been selected. (0 – 255 is
equivalent to 0 – 100%)
7)
Hold the RECORD/SHIFT button down and press twice the REC/EXIT button to leave the programming mode.
Advertisement
