Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for djm direct 01985-V2
Summary of Contents for djm direct 01985-V2
-
Page 2: Device Description
1.Introduction 2.Device Description 1. Saw table MANUFACTURER: 2. Table insert DJM Direct.com 3. Saw blade Unit 43 Churchill Way, 4. Blade guard Lomeshaye Industrial Estate, 5. Suction hose Nelson, Lancashire BB9 6RT UK 6. Riving knife 7. Mitre gauge 8. Table extension DEAR CUSTOMER 9. -
Page 3: Intended Use
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. -
Page 4: Safety Instructions For Table Saws
f) Dress properly. Do not wear loose clothing or jewellery. Keep 6 Safety instructions for table saws your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 6.1 Guarding related Warnings g) If devices are provided for the connection of dust extraction and a) Keep guards in place. - Page 5 aids will help ensure that your hands remain a safe distance from the b) Never reach over or behind the saw blade to pull or support the saw blade. workpiece. This can result in accidental contact with the saw blade, e) Only use the push stick provided by the manufacturer, or a push or kickback can lead to your fingers being drawn into the saw blade.
-
Page 6: Residual Risks
your workpieces. Cramped, dark working areas, and uneven, l) Use only saw blades that are marked with an equal or higher slippery floors may lead to accidents. rotation speed than that marked on the saw. d) Regularly clean and remove sawdust from beneath the saw table m) Use only saw blades recommended by the manufacturer which and/or from the dust extraction system.Accumulated sawdust is conform to EN 847-1, if intended for cutting wood or similar... -
Page 7: Technical Data
Attach the Table Extensions 9. Technical Data 1. Make sure that the saw blade is at its lowest setting. Turn the saw upside down and place it on the floor with the table facing down. Specifications: 2.Line the table extension (8) up with the edge of the saw table (1). Mains Voltage - 220-240V / 50Hz 3. - Page 8 Attaching the Sub-Frame Riving knife and saw blade 1.Attach the legs(17) as shown in the picture. The ends of the Riving knife support struts are fastened using the same screws as the legs, as Remove the saw table insert by undoing the screw (see picture) and shown in the picture.
- Page 9 Adjusting the riving knife Ensure that the mounting blocks projecting lugs engage with the slot in the riving knife. Adjust the riving knife so that it is between 3-5mm from the saw blade. The blade guard mounting hole on the riving knife should be at least 10 mm higher than the tooth peak.
-
Page 10: Operation
3. Fit the outer flange washer and screw in the lock nut. Hold the Unplug the mains lead and let the saw cool down for at least 10 drive shaft with one of the spanners on the outer flange washer minutes. -
Page 11: Maintenance And Cleaning
Mitre gauge 12. Maintenance and Cleaning Slide the mitre gauge into one of the slots on the table. Undo the locking knob (c) and set the desired angle. Tighten the Before any work on the machine itself, pull the mains plug. locking knob again. -
Page 12: Parts List And Parts Diagram
14.Parts List and Parts Diagram Description Description Description Description Spring Carbon brush Washer Bushing - driving rod Rear clamping Brush holder Blade guard plate Self tapping screws plate Extraction hose Actuating arm Spring holder Cross head screws Bearing sleeve Spring pin Block Motor house Bearing... - Page 13 Description Description Miter gauge Self tapping screws indicator 124 Switch Self tapping screws 125 Switch box Miter gauge 126 Switch box cover Knob 127 Screws End cap Miter gauge stop Gear rack rail 129 Hex nut Carriage bolt 130 Hex screws Rod - rip fence Left table support Washer...
-
Page 15: Low Voltage Directive
Table SAW – Part. No. DJM01985-V2 2014/35/EU Low Voltage Directive 2014/30/EU EMC D irective EN IEC 62841-1:2014+C1:2014 EN 55014-1:2017 EN 55014-2:2015 EN IEC 61000-3-2:2019 EN 61000-3-11:2000 EN 61000-3-2:2014 Data: 18/11/2020...
Need help?
Do you have a question about the 01985-V2 and is the answer not in the manual?
Questions and answers