Advertisement
Quick Links
INDEX
Page
Contents
2
3
4
5
7
12
12
AXCOR BEAM 300
INSTRUCTION MANUAL
Congratulations on choosing a Claypaky product!
We thank you for your custom.
Please note that this product, as all the others in the rich
Claypaky range, has been designed and made with total quality
to ensure excellent performance and best meet your
expectations and requirements.
C61730
Advertisement
Related Manuals for ARRI Claypaky AXCOR BEAM 300
Summary of Contents for ARRI Claypaky AXCOR BEAM 300
-
Page 1: Table Of Contents
AXCOR BEAM 300 C61730 INSTRUCTION MANUAL INDEX Congratulations on choosing a Claypaky product! We thank you for your custom. Page Contents Please note that this product, as all the others in the rich Safety Information Claypaky range, has been designed and made with total quality to ensure excellent performance and best meet your Unpacking and preparation expectations and requirements. -
Page 2: Safety Information
SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Claypaky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: www.claypaky.com Ref: [FIS01A – Safety Information Axcor 300 series] INFORMAZIONI DI SICUREZZA IMPORTANTE: Claypaky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link: www.claypaky.com Rif: [FIS01A –... -
Page 3: Unpacking And Preparation
UNPACKING AND PREPARATION Packing contents - Fig. 1 LOCKED UNLOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 AXCOR BEAM 300... -
Page 4: Installation And Start-Up
INSTALLATION AND START-UP Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base. -
Page 5: Control Panel
CONTROL PANEL Mains NB: connecting one Axcor Beam 300 to the mains, it is possible to connect up to a maximum 11 @ 200-240Vac or 5 @ 100-120Vac Axcor Beam 300 in parallel at the same time. Max 2800VA. Connecting to the mains supply - Fig. 6 DMX 512 5 PIN DMX 512... - Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
-
Page 7: Maintenance
MAINTENANCE 1/4 Turn 1/4 Turn Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11. ‘ Continue AXCOR BEAM 300... - Page 8 Lower Side Upper Side Periodical cleaning - Fig. 12 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
- Page 9 Cleaning of the filters - Fig. 13 Upper Side Extraction of the effect modules - Fig. 14 IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 14 in reverse order. ‘...
- Page 10 Fuse 5x20mm T3.15A 250V Replacing fuse - Fig. 15 AXCOR BEAM 300...
- Page 11 Battery removal - Fig. 16 This product contains a rechargeable battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. AXCOR BEAM 300...
-
Page 12: Dimensions
DIMENSIONS (13.77") (12.48") (13.77") (19.29") (17.56") (13.77") (10.83") CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON ELECTRONICS NON-OPERATIONAL PROBLEMS DEFECTIVE PROJECTION REDUCED LUMINOSITY POSSIBLE CAUSES CHECKS AND REMEDIES No mains supply. Check the power supply voltage. LED engine defective. Replace LED engine.