Advertisement
TOOLS NEEDED
• 5/8" and 1/2" open wrench or socket and socket wrench
• Hex head screw driver
• Square
WARNING
• Do not use the stand for scaffolding or as a ladder.
• Make sure to securely tighten all fasteners before using.
• Maximum capacity is 300 lbs (136 kg).
NOTE: Use a square to verify all of the components are
perpendicular before fully tightening hardware.
BASE AND CASTER ASSEMBLY
ITEM DESCRIPTION
A
Long Base Rails
B
Short Base Rails
C
Caster Assembly
D
Wheels
E
Wheel Brackets
F
Leveler Assemblies
N
5/16"-18 x 2" Hex Head Bolts
O
5/16"-18 x 2-1/2" Hex Head Half Thread Bolts
P
5/16"-18 Nylon Lock Nuts
Q
5/16"-18 x 5/8" Carriage Bolts
R
5/16" Lock Washers
S
5/16"-18 Nuts
1.
See Figure 2. Slide the Short Base Rails (B) into the Long
Base Rails (A) aligning corners. Pay attention to location of
the three holes in Long Base Rails (A) this will be the back.
From the bottom, slide one 5/16"-18 x 2" Hex Head Bolt (N)
through the corner holes on Long and Short rails. Repeat
on all four corner holes. Secure each Hex Head Bolt (N) with
one 5/16" Lock Washer (R) and one 5/16"-18 Nut (S). Tighten
the hardware. Repeat for remaining two holes on Short Base
Rail (B) in back location. This creates the frame base.
Figure 2
NOTE: The outside 5/16"-18 x 5/8" Carriage Bolts (Q) are used
to attach the leg and wheel bracket to the frame base. Do this
after the legs are attached.
ASSEMBLY
2.
See Figure 3. Center Wheel (D) inside Wheel Bracket (E).
Align to side-holes on the Long Base Rail (A). Insert 5/16"-
18 x 2-1/2" Hex Head Half Thread Bolt (O) through center
round hole in Bracket (E), through Wheel (D) and into center
round hole on Long Base Rail (A). Secure bolt with 5/16"-18
Nylon Lock Nut (P). Tighten the Lock Nut (P) until snug yet
allowing the wheel to turn freely.
NOTE: Leave the left square hole of Bracket (E) open at this time.
3.
Insert one 5/16"-18 x 5/8" Carriage Bolt (Q) through the
right square hole in Bracket (E) and Long Base (A). Secure
with Lock Washer (R) and Nut (S). Repeat for other side of
frame base.
Figure 3
Items Needed
QTY
2
2
1
2
2
2
6
2
2
4.
See Figure 4. Install the Leveler Assemblies (F) to the Short
2
Base Rail (B) front, opposite the wheels. Remove one of
8
the nuts from the threaded section of the leveler. Insert the
Leveler Assembly (F) through the bottom of Short Base
8
Rail (B) and secure with the removed nut. To adjust, see the
Adjust Leveler Assemblies section.
5.
The Caster Assembly (C) can be mounted inboard or
outboard to the frame base (shown as outboard installation).
a. Align the holes on the Caster Assembly (C) with the
b. Insert two Hex Head Bolts 5/16"-18 x 2" (N) through
c. Secure the pedal to Base Rail (B) by tightening with two
Figure 4
CAUTION
Tripping and/or other personal injury may result. Keep the planer
stand out of walkways when the caster assembly pedal is in the
outboard position on the stand.
holes on the Short Base Rail (B) frame.
frame base and holes of the pedal.
5/16" Lock Washers (R) and 5/16"-18 Nuts (S).
3
3
Advertisement
