Advertisement
WARNING
For your own safety, read all of the rules and precautions before
operating tool.
WARNING
• This product was designed to be used as a Planer Stand
for planers. Do not overload. The maximum capacity for the
Planer Stand is 300 lbs (136 kg).
• Do not use for scaffolding or as ladder. Do not stand or climb
on the Planer Stand; it could tip over, causing serious injury.
• Do not apply an unbalanced load. This could cause the Planer
Stand to tip over.
• Store the Planer Stand properly. Do not store the Planer
Stand outdoor or in a damp location.
• Keep the work area clean, uncluttered, and well lit. Do not
work on or place the Planer Stand legs on oor surfaces that
are slippery from sawdust, oil, water or wax.
• Keep children and bystanders away while operating a power
tool. Distractions may cause you to lose control. Visitors
should wear the same safety equipment as the operator.
• Properly secure the planer to the Planer Stand before
operation. Follow the mounting instructions carefully. Fasten
the tool to the MDF top securely as instructed.
• Place the Planer Stand on a at level surface to prevent
rocking or tipping.
• Make sure the Planer Stand is rmly on the oor, the foot
pedal is down and the wheel is raised before use.
• Always wear safety glasses or eye shields when operating
power tools.
• Dress properly. Do not wear loose clothing or jewelry. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught in moving parts.
Always wear non-slip footwear. Tie back long hair. Roll long
sleeves above the elbow.
• Always use clamps or other practical ways to support the
workpiece and secure it to a stable platform. Holding the
workpiece by hand or against your body is unstable and may
lead to loss of control.
• Check all hardware prior to mounting any bench top tools.
• Inspect all hardware periodically; tighten anything loose.
• Be sure to use the proper mounting bolts for the unit being
attached to the Planer Stand.
WARNING
Do not modify this Planer Stand and/or use it for any application
other than that for which it was designed.
WARNING
Always follow proper operating procedures as de ned in this
manual even if you are familiar with use of this Planer Stand
or any tool used with this Planer Stand. Remember that being
careless for even a fraction of a second can result in severe
personal injury.
You must be familiar with the use of any tool or accessory used
with this Planer Stand. The supplier cannot be held responsible
for any accident, injury or damage incurred while using this
Planer Stand with any tool.
SAFETY RULES
FOLLOW ALL STANDARD SHOP SAFETY
PRECAUTIONS, INCLUDING:
• Keep children and visitors at a safe distance from work area.
• Keep work area clean. Cluttered work areas invite accidents.
Work area should be properly lit.
• Do not use power tools in dangerous environments. Do not
use power tools in damp or wet locations. Do not expose
power tools to rain.
• Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of the tool.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant lenses.
They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
• A guard or any other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs.
• Use the right tool for your job. Do not force your tool to do a
job for which it was not designed.
• Use safety equipment such as featherboards, push sticks and
push blocks, etc., when appropriate.
• Maintain proper footing at all times and do not overreach.
• Do not use this Planer Stand as a step or seat.
WARNING
• To avoid serious injury, turn off and unplug the planer before
attaching or changing accessories or adjusting the cutter
height position.
CAUTION
Think safety! Safety is a combination of operator common sense
and alertness at all times when tool is being used.
WARNING
Do not use the Planer Stand until it is completely assembled
and you have read and understood this entire operating
manual and the operating manual of the tool being used with
this Planer Stand.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
1
1
Advertisement
