Graco QuickShot Quick Manual

Graco QuickShot Quick Manual

Advertisement

QUICK GUIDE
WARNING
Read Owner's Manual (3A9301) for complete instructions and warnings.
This quick guide is not a substitute for reading and understanding all
instruction manuals and warning labels supplied with the equipment.
Manuals are available at
graco.com
Follow pressure relief procedure and wear protective equipment including
but not limited to protective eye wear.
SKIN INJECTION HAZARD: Keep clear of spray tip and leaks. Engage trigger
lock when not spraying.
FIRE AND EXPLOSION HAZARD: Use only non-flammable or water-based
materials. Follow fire and explosion warnings as listed in your manual.
FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY,
AMPUTATION, OR DEATH.
Instructions in Quick Guide are for water-based paints only. See Owner's
Manual for instructions for use with Oil-Based or Flammable materials.

KNOW YOUR SPRAYER

Spray
Spray Tip
Spray Tip Guard
Gun
Belt Clip
Trigger
Flow
Control
Trigger
Lock
Battery
Holster
Release Clip
Belt
Holster
Prime Knob
PRIME
Turn Prime knob up
to PRIME position to
relieve system pressure.
Turn Prime Knob
forward to SPRAY
position to spray fluid.
1
Engage Trigger lock.
• No visible red showing on
trigger lock is the locked
position.
• Always engage trigger lock
when not spraying.
2
Turn Prime Knob up to PRIME
position.
3
Remove the cup lid from the
cup.
4
Verify a clean pump filter is
installed in the bottom of the
Storage Plug
cup at the pump inlet.
• A dirty or plugged pump filter
Cup Lid
will result in poor sprayer
operation or loss of prime.
Cup
Cup Release
Lever
5
Fill cup with paint and
Cup Support
reinstall Cup Lid.
• Instructions in Quick Guide are
for water-based paints only.
Pump Filter
• See owners manual for
instructions for use of Oil-Based
or Flammable materials.
Prime Knob
1
Belt Latch
SPRAY
3 3

SPRAYER SETUP

ti42428a

BELT SETUP

2 2
4

START UP

1
Disengage Trigger Lock and
verify Prime Valve Knob is in
the PRIME position.
2
Turn the Spray Tip to the
UNCLOG position and Install
a fully charged battery.
3
Verify Storage Plug is OPEN.
• Storage plug must be open
during spraying to avoid an
air lock in the cup and loss of
prime.
4
To prime the pump, point
the gun into a waste pail
and pull the trigger for 10
seconds.
• This will purge air from the
pump.
• The electronic gun is always
open when the trigger is
pulled, so a small amount
of fluid may spray out while
priming.
5
Turn the Prime Valve knob
forward to the SPRAY
position.
6
To prime the hose and gun,
point the gun into a waste
pail and pull the trigger for
10 seconds or until there is a
steady stream of paint.
• This will purge all air (and
storage fluid) from the hose
and gun.of fluid may spray out
while priming.
7
Turn the Spray Tip forward to
the SPRAY position.
NOTE: To avoid pump damage, if gun does not spray after
10 seconds STOP and repeat STARTUP.
You are now ready to spray!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QuickShot and is the answer not in the manual?

Questions and answers

Summary of Contents for Graco QuickShot

  • Page 1 Manuals are available at graco.com Follow pressure relief procedure and wear protective equipment including but not limited to protective eye wear. SKIN INJECTION HAZARD: Keep clear of spray tip and leaks. Engage trigger Verify Storage Plug is OPEN.
  • Page 2 Turn Spray Tip 90 degrees to seal orifice from drying out. Remove Pump Filter from cup and set Close Storage Plug in Cup Lid to seal aside for cleaning. material in Cup. ©2022 Graco Distribution BV 3A9323ENEU-A 06/23. Printed in Europe. Source Manual: 3A9301, MM 3A9323.

Table of Contents