Philips M32 107E4 GS 3 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. Monitor
  5. M32 107E4 GS 3
  6. Service manual
Philips M32 107E4 GS 3 Service Manual

Philips M32 107E4 GS 3 Service Manual

17" auto scan colour monitor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
17" Auto scan Colour Monitor
DDC/Power saving/MPR II/TCO
Description
Important Safety Notice ------------------------------- 2
Technical Data ------------------------------------------ 3
Front control & OSD------------------------------------ 4
OSD menu tree------------------------------------------ 5
OSD Adjustments-----------------------------------6~12
Troubleshooting----------------------------------------12
Service mode--------------------------------------------13
Warning and Notes ------------------------------------ 14
Mechanical Instructions ------------------------- 15~17
Wiring Diagram------------------------------------------18
Hex Data of DDC2B--------------------------------19 ~21
DDC Instructions -----------------------------------22~26
Electrical Adjustments --------------------------- 27~ 29
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitors
Printed in Taiwan

TABLE OF CONTENTS

Description
Page
Block Diagram ------------------------------------------31
Video Panel C.B.A.(A) --------------------------------33
Main Panel-Deflection (B) Schematic Diagram --34
Main Panel C.B.A.(B,C)-------------------------------35
Power Supply (C) Schematic Diagram-------------36
Key Control Panel (D) Schematic Diagram -------37
Key ControlPanel C.B.A. (D) ------------------------38
Repair Tips ----------------------------------------------39
Exploded View------------------------------------------40
Recommended parts list------------------------------41
Spare parts list------------------------------------- 42~44
Repair flow chart----------------------------------- 45~52
General Product Specification-------------------53~81
General Troubleshooting Guide----------------82~104
SAFETY NOTICE
Copyright reserved
Subject to modification
Chassis :M32
M32 107E4 GS_3
107E41/00C
Horizontal frequencies
30 - 70 kHz
Jul 15 2002
Page
3138 106 10214

Advertisement

Table of Contents
loading

Related Manuals for Philips M32 107E4 GS 3

Summary of Contents for Philips M32 107E4 GS 3

  • Page 1: Table Of Contents

    17" Auto scan Colour Monitor Chassis :M32 M32 107E4 GS_3 DDC/Power saving/MPR II/TCO 107E41/00C Horizontal frequencies 30 - 70 kHz TABLE OF CONTENTS Description Page Description Page Block Diagram ------------------------------------------31 Important Safety Notice ------------------------------- 2 Video Panel (A) Schematic Diagram ---------------32 Technical Data ------------------------------------------ 3 Video Panel C.B.A.(A) --------------------------------33 Front control &...

  • Page 2: Important Safety Notice

    REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR evaluation. Accordingly, a servicer who uses a service PART NUMBERS IN THE PARTS LIST SECTION OF THIS procedure or tool which is not recommended by PHILIPS SERVICE MANUAL. must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

  • Page 3: Technical Data

    <2 w Relative Humidity : 5 % - 95 % (W/O condensation) This monitor is ENERGY STAR compliant. As an ENERGY STAR Partner, PHILIPS has determined that Pin assignment : this product meets the ENERGY STAR guidelines for energy efficiency ENERGY STAR is a U.S.

  • Page 4: Front Control & Osd

    Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor.

  • Page 5: Osd Menu Tree

    OSD menu tree M32 107E4 GS_3 Go to cover page The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments.

  • Page 6: Osd Adjustments

    OSD Adjustments M32 107E4 GS_3 Go to cover page The OSD Controls LANGUAGE The ON SCREEN DISPLAY shows its settings in one of five languages. The default is English, but you can select French, Spanish, German, or Italian. BRIGHTNESS To adjust your screen's brightness, follow the steps below. Brightness is 1) Press the button on the monitor.
  • Page 7 OSD Adjustments (Continued) M32 107E4 GS_3 Go to cover page ZOOM 3) Press the button. The ADJUST HORIZONTAL window appears. ADJUST POSITION should be highlighted. ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below. 1) Press the button on the monitor.
  • Page 8 OSD Adjustments (Continued) M32 107E4 GS_3 Go to cover page 2) Press the button until ADJUST SHAPE is highlighted. 2) Press the button until ADJUST VERTICAL is highlighted. 3) Press the button. The ADJUST SHAPE window appears. 3) Press the button.
  • Page 9 OSD Adjustments (Continued) M32 107E4 GS_3 Go to cover page Smart Help After returning to MAIN CONTROLS . . . 7) When the trapezoid is adjusted, press the button to highlight ...to continue to ADJUST SIDE ANGLES, start with step 5 under PARALLELOGRAM or press the button to return to the ADJUST ADJUST SIDE ANGLES and follow the directions.
  • Page 10 OSD Adjustments (Continued) M32 107E4 GS_3 Go to cover page 4) Press the button to highlight 9300K for GENERAL USE, 5) Press the button. The ROTATE IMAGE window appears. ROTATE 6500K for GAMES, or USER PRESET. should be highlighted. 5) Once you have highlighted GENERAL USE or GAMES, press the button to confirm you selection and return to the MAIN CONTROLS window.
  • Page 11 OSD Adjustments (Continued) M32 107E4 GS_3 Go to cover page 4) Press the button to select YES or NO. NO is the default. 4) Press the button. The ADJUST MOIRE window appears. YES returns all settings to their original factory adjustments. HORIZONTAL will be highlighted.

  • Page 12: Troubleshooting

    M32 107E4 GS_3 OSD Adjustments (Continued), Troubleshooting Go to cover page DEGAUSS Monitor Specific Troubleshooting EXTRA CONTROLS is a set of three features, including DEGAUSS. Self-Test Feature Check (STFC) Degaussing removes electromagnetic build up that may distort the color Your monitor provides a self-test feature that allows you to check on your screen.

  • Page 13: Lock/Unlock, Factory Mode, Burn In

    Lock/Unlock, Factory Mode, Burn In, Service Mode M32 107E4 GS_3 Go to cover page To access factory mode Front Control 1. Turn off monitor (don't turn off PC) 2. Press " " and " " simultaneously on the front control panel,then press "...

  • Page 14: Warning And Notes

    Warning and Notes M32 107E4 GS_3 Go to cover page Warnings Notes 1. Safety regulations require that the unit should be returned 1. The direct voltages and waveforms are average voltages. in its original condition and that components identical to They have been measured using the Service test software the original components are used.

  • Page 15: Mechanical Instructions

    Mechanical Instructions M32 107E4 GS_3 Go to cover page 0. General To be able to perform measurements and repairs on the "circuit boards", these unit should placed in the service position first. 1.Remove the rear cover lids (screw cover) -Remove right and left lib (screw cover) on the back cover as shown in Fig.
  • Page 16 M32 107E4 GS_3 Mechanical Instructions Go to cover page 4. Main panel with Bottom Tray - Disconnect the degaussing coil (1113)from Main panel as shown in Fig. 6. - Remove the video panel from CRT neck. - Remove the "screw" of I/F cable from Main panel, grounding screw , wire as shown in Fig.
  • Page 17 Mechanical Instructions M32 107E4 GS_3 Go to cover page 5. How to remove Main Panel (Chassis) After remove "Main panel with bottom tray": Fig. 18 - Remove a screw from back of bottom tray as shown in Fig. 15. - Remove Interface cable from bottom tray as shown in Fig. 16. - Remove a screw from Main panel as shown in Fig.

  • Page 18: Wiring Diagram

    Wiring Diagram M32 107E4 GS_3 Go to cover page...

  • Page 19: Hex Data Of Ddc2B

    : TY 123456 White Y coordinate : 0.297 Monitor Descriptor #3 Established Timings Monitor Name : PHILIPS 107E4 Established Timings I : 720 x 400 @70Hz (IBM,VGA) 640 x 480 @60Hz (IBM,VGA) Monitor Descriptor #4 640 x 480 @72Hz (VESA)
  • Page 20 Established Timings Monitor Descriptor #3 Established Timings I : 720 x 400 @70Hz (IBM,VGA) Monitor Name : PHILIPS 107E4 640 x 480 @60Hz (IBM,VGA) Monitor Descriptor #4 640 x 480 @72Hz (VESA) Monitor Range Limits 640 x 480 @75Hz (VESA) Min.
  • Page 21 Hex Data of DDC2B (Continued) M32 107E4 GS_3 Go to cover page ********************************************************************** Standard Timing Identification #6 M32 107E4 70K Philips Tube EDID log file Horizontal active pixels : 800 ********************************************************************** Aspect Ratio : 4:3 Vendor/Product Identification Refresh Rate : 100...

  • Page 22: Ddc Instructions

    DDC Instructions M32 107E4 GS_3 Go to cover page 1. General 3. Pin assignment DDC Data Re-programming A. 15-pin D-Sub Connector In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect,repaired monitor the serial numbers have to be re-programmed.
  • Page 23 DDC Instructions (Continued) M32 107E4 GS_3 Go to cover page 4. Configuration and procedure 3. At the submenu, type the letter of your computer's floppy disk drive followed by :EDID301 (for example, A:\EDID301, as shown in Fig. 5). There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores all factory settings and DDC data (EDID code) which is so called Software DDC.
  • Page 24 DDC Instructions (Continued) M32 107E4 GS_3 Go to cover page Re-programming EEPROM (Software DDC) 4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 13. Step 1: After initialize alignment box, connecting all cables and box as shown in Fig.
  • Page 25 DDC Instructions (Continued) M32 107E4 GS_3 Go to cover page Step 5: **Configuration Setup & Enter Factory Mode ** Step 6: Write DDC data for "write EDID data" Click (Write EDID) icon from the tool bar to write DDC data. Bring up "Writing 0%~100%, ready"...
  • Page 26 DDC Instructions (Continued) M32 107E4 GS_3 Go to cover page Step 9: Load DDC data Note 2 : In Factory Mode: Read/Write DDC data Before Read/Write EDID code, please confirm that the Click from the tool bar. Software DDC only was enabled as shown in Fig. 23. Select the file you want to open as shown in Fig.

  • Page 27: Electrical Adjustments

    Electrical Adjustments M32 107E4 GS_3 Go to cover page 5. To access factory mode 0. General 5.1 Turn off monitor (don't turn off PC) 5.2 Press " " and " " simultaneously on the front control When carry-out the electrical settings in many cases a video signal panel,then press "...
  • Page 28 ( for ref. 4,4) gain. LF (BRIGH SHARP) (for ref. 230) 48K SUB OSD R/G/B cut-off and R/G/B gain can be accessed (for Philips EXIT CRT), with initial data: Fig. 2.2 9300 K (for example: 152 is value of "BIAS R")
  • Page 29 Electrical Adjustments (Continued) M32 107E4 GS_3 Go to cover page 8. Focus adjustment Apply a signal of " @ " character. at 68.7 kHz/85 Hz mode set the brightness to mid-position , contrast to max - position and adjust the focus for optimal sharpness in the area within 2/3 from the screen center.

  • Page 30: Safety Test Requirements (Hipot & Ground)

    Safety test requirements M32 107E4 GS_3 Go to cover page All units that are returned for service or repair must pass the 3. Equipments and Connection original manufactures safety tests. Safety testing requires both Hipot and Ground Continuity testing. 3.1. Equipments For example : HI-POT TEST INSTRUCTION - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY...

  • Page 31: Block Diagram

    M32 107E4 GS_3 Block diagram Go to cover page FUNCTION BLOCK OF COCA+ M32 107E4 GS_3 VIDEO VIDEO LIGHT & OUTPUT AMPLIFIER RESTOR. FRAME DEFLECTION UNIT STAGE STV9211 BF422 x 6 TDA4822 STV9556 ROTATION LM358N OSD IC WT62P2 Self- test S-CAP H-OUTPUT/ LOT VIDEO...

  • Page 32: Video Panel (A) Schematic Diagram

    Video Panel Schematic diagram M32 107E4 GS_3 Go to cover page A1 7302-2 A4 1713-8 2 V/div AC 1 V/div AC 5 mS/div 5 mS/div 4.2V 1.6V A1 7302-4 A5 1713-7 4.2V 1.6V 4.2V 1.6V 62.3V 1 V/div AC 2 V/div AC 62.8V 5 mS/div 5 uS/div...
  • Page 34 M32 107E4 GS_3 Go to cover page 54662SMC 54662HMC (SMD) (POSITION) 2301 A4 1301 B1 3738 D3 3350 A2 2302 A5 1703 D2 3751 B4 3355 A3 2304 A1 1711 C3 3752 B4 3361 A2 2305 A1 1712 C2 3753 E5 3362 A2 2306 A1 1713 C1...
  • Page 36 diagram B1 7503-C B8 7501-6 7610-D B22 7685-C B29 7801-18 50 V/div AC 5 V/div AC 100 V/div AC 0.5 V/div AC 50 V/div AC 5 mS/div 10 uS/div 10 uS/div 5 mS/div 10 uS/div B2 7501-14 B23 5612-6 7501-4 B16 7612-B B30 7801-8 2 V/div AC...

  • Page 38: Main Panel C.b.a.(B

    Main Panel C.B.A.(B,C) - copper track side view M32 107E4 GS_3 Go to cover page 3126 G5 2615 A3 3622 C4 3849 F7 9126 D4 6609 B1 3127 G5 2616 B4 3623 B4 3851 F7 9127 D4 GRID BOARD 6612 A4 3128 F5 2617 A4 3624 B5...
  • Page 40 5113-1 100 V/div AC 5 uS/div 5113-4 5 V/div AC 5 uS/div 5113-8 10 V/div AC 5 uS/div 5113-13 100 V/div AC 5 uS/div 5113-10 10 V/div AC 5 uS/div 7101-G 5 V/div AC 5 uS/div 7111-4 10 V/div AC 5 uS/div...
  • Page 41 F891 C1 F892 C1 F893 C1 F894 C1 8891 JFE3309H F891 F892 F893 F894 ENTER DOWN RIGHT LEFT TYT12- -------- CLASS NO. KEY CONTROL 3138 178 62711 M32 107E41/00C(MPR2) 02-04-26 TM Hsiao NAME SUPERS 02-04-26 Philips Electronics N.V. CHECK DATE...

  • Page 42: Key Controlpanel C.b.a

    Key Control Panel C.B.A.(D) M32 107E4 GS_3 Go to cover page 1891 A2 1892 A2 1893 A2 1894 A3 1895 A4 3891 A2 3892 A3 3893 A2 3894 A3 3895 A3 6891 A1 8891 A4 53022cus 53022hmc...

  • Page 43: Repair Tips

    Repair Tips M32 107E4 GS_3 Go to cover page preferably be equipped with a thermal control (soldering 0. Warning temperature: 225 to 250 C). - The chip, once removed, must never be reused. All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD).

  • Page 44: Exploded View

    Exploded view M32 107E4 GS_3 Go to cover page 3138 127 52891 FRONT CABINET ASSY 9322 171 29682 17"CRT M41AGE83X46C(CPT) 1050 9301 907 40323 17"CRT M41LFQ903x39(LA)(LGPD) 9301 869 30323 17"CRT M41EHN323x160/G372BA(PH) 1053 3138 178 62711 KEY CNTR PCB ASSY 5007 3138 168 79991 DEGAUSSING COIL 3138 178 63011...

  • Page 45: Recommended Parts List

    Recommended Parts List M32 107E4 GS_3 Go to cover page Recommended parts list of 107E41/00C 0001 313812752891 FRONT CABINET ASSY 0002 313812750081 BACK COVER ASSY 0003 313810798401 PEDESTAL ASSY 0047 313810454651 BUTTON-POWER 0049 313810454661 BUTTON-FUNCTION 0051 313810454081 SCREW COVER 0178 313810540481 SETTING UP GUIDE 0450 313810667131 CARTON 0451 313810656344 CUSHION - RIGHT 0452 313810656353 CUSHION - LEFT...

  • Page 46: Spare Parts List

    Spare Parts List M32 107E4 GS_3 Go to cover page Parts List 2401 225261508411 CER2 DC Y5P 50V S 470P PM10 A 2402 203803511222 ELCAP REA 16V S 470U PM20 A CTV : 107E41/00C 2403 222236525473 CAP MPOL 1V S 47N PM10 A 3101 232224213105 RST MGL VR37 A 1M PM5 A 2405 203803511507 ELCAP REA 50V S 47U PM20 A 3102 213866000027 NTC DC SCK-104 S 10R PM15 B...
  • Page 47 Spare Parts List (Continued) M32 107E4 GS_3 Go to cover page 3612 232220733228 RST FUSE NFR25H A 2R2 PM5 A 3613 213810113103 RST CRB CFR-12 A 10K PM5 A 3614 213810113223 RST CRB CFR-12 A 22K PM5 A 3616 213810113124 RST CRB CFR-12 A 120K PM5 A 3617 213810113223 RST CRB CFR-12 A 22K PM5 A 3618 212211000427 RST MFLM MF1/2WS A 470K PM1 7101 932215891687 FET POW STP6NC60...
  • Page 48 Spare Parts List (Continued) M32 107E4 GS_3 Go to cover page 1052 Video PCB ASSY(313817863001)(PHL) 1053 CONTROL PCB ASSY 1052 313817863011 VIDEO PCB ASSY(CPT) 1053 313817862711 CONTROL PCB ASSY 1052 313817863021 VIDEO PCB ASSY(LG) 5721 242253597725 IND FXD SP0305 A 0U22 PM20 B 5732 242253597725 IND FXD SP0305 A 0U22 PM20 B 5752 242253597725 IND FXD SP0305 A 0U22 PM20 B 5761 243853598025 IND FXD BEAD EMI 1MHZ 60R R...

  • Page 49: Repair Flow Chart

    Repair Flow Chart M32 107E4 GS_3 Go to cover page A. Power Supply Failure 1. Sympton : check 7102 pin8 check 7102 check 7102 check 7102 no startup sound 100V<pin8<380V pin1 > 2V pin 5=2.4V pin6 output ? LED light off check check check...
  • Page 50 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page rough check for R,G, B B.Video 1. video input= 0.7V check blanking Repair Flow 2. 7301video output =2.5V 7501 pin16 3. 7701 video output > 35Vpp check 1.Sympton : R,G,B output (with wite pattern) check heater...
  • Page 51 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page C. Horizontal deflection output repair flow : 1. Sympton : check Hsync check Hsync check Hsync without 7606 base 7605 base 7501 pin8 H-deflection. check check Hsync check Hsync replace 5612 180V 7603 drain...
  • Page 52 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page basic check D. Vertical Deflection Failure +12/-12V Sympton : check check one horizontal line 3401,3403 6401 V_size is abnormal 3404 good? too large/small good check check 7401 7401 check 7501 check pin12,pin13 ramp 3412,3411...
  • Page 53 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page check cpu pin6= 5V E. CPU Basic Check pin9/pin8=12MhZ check list pin7=gnd H size compensation for 70K S-CAPACITOR SWITCH TABLE 31. H-EHT the load variance Hor. Freq.(KHz) < 27.00 27.50-33.24 33.24-36.51 36.51-42.38...
  • Page 54 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page check 38. Rotation output from 0V to 5V check 3. ABL-CON output from 0V to 5V check key check 3836, 2822 23. Keypad Enter,Up,Down,Left,Right keys 3871~3875 check pin24 1.no H/V sync & IF cable pin5 floating - show msg.
  • Page 55 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page Basic check F. TDA4841 Vcc=pin9=pin10=12V Vcc > 9V Check List gnd =pin7=pin25=0v during startup 1. HFLB pin16 if no exist (from H.defl) CLBL=hi pin17 = Hunlock = floating pin30 = Hpll2 = 0V pin6 = HDRV = floating 2.
  • Page 56 Repair Flow Chart (Continued) M32 107E4 GS_3 Go to cover page Hunlock pin is floating while pll1(pin26) is 17. Hunlock unlock in searching mode 18. IIC scl = hi the initial sequence of IIC IC 19 IIC sda = hi 7501,7301,7304 compensate for the V_size 21 EHT_compen.

  • Page 57: General Product Specification

    . REAL MULTI-FREQ. - POWER SAVING MANAGEMENT SYSTEM - MAXIMIZED CONTAINER LOADING - VESA DDC2B - LOW EMISSION MPRII / TCO99/TCO95 (Optional) 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 58 Focus check 4.10 Luminance uniformity 4.11 White color adjustment 4.12 Color tracking on full white pattern 4.13 Purity 4.14 Moir 4.15 Blemish 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 59 Leakage current Grounding Certifications Safety Fulfil approbation requirements Reliability Mean time between failures 10.0 Quality assurance requirements 10.1 Acceptance test 11.0 Service ability 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 60 (between 0 and 0.6 V to be considered as low level ,between 2.3 and 5.0 V as high level) C. Impedance Video : Terminated with 75 ohms Sync : Terminated with 4.7K ohms pull down resistors. 17" M32 GS3 107E4-70K CMTR TYPE : 107E41/00C 8639 000 12205 BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 61 6. 1024 x 768 60.0 KHz 75Hz (VESA) 7. 1024 x 768 68.7 KHz 85Hz (VESA) 8. 1280 x 1024 64.0 KHz 60Hz (VESA) 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 62 The AUTOSCAN color monitor must be capable of displaying standard resolutions within the vertical(refresh) frequency range of 50 to 160 Hz and horizontal scan range of 30 - 70 KHz. 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 63 Rear porch = 3.232 us Rear porch 0.448 ms Sync width = 1.616 us Sync width 0.064 ms Sync.polarity = Sync.polarity = 17" M32 GS3 107E4-70K CMTR TYPE : 107E41/00C 8639 000 12205 BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 64 = 11.183 ms Rear porch = 2.201 us Rear porch 0.524 ms Sync width 1.016 us Sync width 0.044 ms Sync.polarity = Sync.polarity 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 65 Rear porch = 4.064 us Rear porch 0.739 ms Sync width = 1.270 us Sync width 0.079 ms Sync.polarity = Sync.polarity = 17" M32 GS3 107E4-70K CMTR TYPE : 107E41/00C 8639 000 12205 BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 66 = 12.480 ms Rear porch = 1.280 us Rear porch 0.478 ms Sync width = 2.400 us Sync width 0.125 ms Sync.polarity = Sync.polarity 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 67 = 13.599 ms Rear porch = 1.920 us Rear porch 0.513 ms Sync width 1.813 us Sync width 0.106 ms Sync.polarity = Sync.polarity 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 68 = 16.000 ms Rear porch = 2.889 us Rear porch 0.600 ms Sync width 1.037 us Sync width 0.050 ms Sync.polarity = Sync.polarity 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 69 Implosion protection : By P-Mini-rim-band. : 25.0 1 KV (Ib=0) Visible screen area : 327.2 mm x 245.44mm CRT Source : PHILIPS tube, CPT tube, LG tube,SDI 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS...
  • Page 70 The display device is sufficiently protected against the burning of phosphors in case of repetitive power cycling or absence of horizontal deflection. 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 71 The dimensions of guaranteed display area to be measured along the picture center of horizontal and vertical axis of the screen as listed below: (preset modes only, refer to fig. 1) 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 72 X. Max. - X. min. H. non-linearity = x 100% X. Max. Y. Max. - Y. min. V. non-linearity = x 100% Y. Max. 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 73 (brightness control at center click position), the color co-ordinates should not deviate more than the following tolerance when compare to display center: X= X (center) 0.015 Y= Y (center) 0.015 17" M32 GS3 107E4-70K CMTR TYPE : 107E41/00C 8639 000 12205 BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 74 SEMKO SEMKO Finland Norway NEMKO NEMKO -- Denmark DEMKO DEMKO DEMKO Italy Netherlands KEMA KEMA KEMA U.K. ASTA ASTA U.S.A. Canada Australia 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 75 Container size Q'ty W/ pallet W/ pallet Layers Sets per layer Sets per block Blocks per container 24 Total sets B-2 Transportation standards 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 76 Display disturbances to external environment The disturbances induced by the display and tolerated by the environment are defined as follows : 6.3.1 Ionizetic radiation 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 77 SEMKO ---- Norway NEMKO ---- Denmark DEMKO ---- Finland FIMKO ---- Spain HOMOLOGATION BEAB U.S.A. UL , DHHS Canada Japan ---- VCCI 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 78 The service ability of this monitor should fulfil the requirements which are prescribed in UAW-0346 and must be checked with the check list UAT - 0361 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 79 GENERAL PRODUCT SPECIFICATION M32 107E4 GS_3 Go to cover page 303 mm 306 mm 309 mm FIG-1 IM AGE D IMEN SION 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 80 M32 107E4 GS_3 GENERAL PRODUCT SPECIFICATION Go to cover page 306 mm |A-B| AND |C-D| < 5 mm FIG-2 IMAGE CENTERING 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 81 GENERAL PRODUCT SPECIFICATION M32 107E4 GS_3 Go to cover page 306 mm < 2 mm FIG-3 IMAGE ROTATION 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 82 M32 107E4 GS_3 GENERAL PRODUCT SPECIFICATION Go to cover page 306 mm A=B=C=D < 2.0 mm FIG-4 IMAGE GEOMETRY 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 83 GENERAL PRODUCT SPECIFICATION M32 107E4 GS_3 Go to cover page 100 mm ZONE B ZONE A 306 mm FIG-5 CONTRAST AND BRIGHTNESS MEASUREMENT AREA 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 84 M32 107E4 GS_3 GENERAL PRODUCT SPECIFICATION Go to cover page ZONE B ZONE A ZONE C 306 mm FIG-6 MISCONVERGENCE 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...
  • Page 85 GENERAL PRODUCT SPECIFICATION M32 107E4 GS_3 Go to cover page Figure 7 Focus check character 17" M32 GS3 107E4-70K CMTR 8639 000 12205 TYPE : 107E41/00C BRAND : PHILIPS 2002-04-26 JIM LIN 2002-04-26...

  • Page 86: General Troubleshooting Guide

    General Troubleshooting Guide M32 107E4 GS_3 Go to cover page General Troubleshooting Guide No Display, Unstable Picture/ but LED is ON Picture Flickers or LED is amber (yellow) H/V Rolling, Monitor drivers H/V Sync. (inf file) Picture too bright Focus Picture too dim Degaussing Picture distortion...
  • Page 87 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page NO DISPLAY, but LED is ON or LED is amber(yellow) Green Amber Amber? or Green? Make sure the correct signal is input. Is the ATTENTION Make sure of the state of the computer CHECK SIGNAL CABLE picture displayed? (Turn on).
  • Page 88 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Picture is too bright or dark Press the OK button Bring up "MAIN CONTROLS" window Select "RESET TO FACTORY SETTINGS" Make sure of the signal cable connection. Make sure of the state of the computer (Turn on).
  • Page 89 Philips' monitors build in VESA DDC2B feature to support Plug & Play requirement for Windows 95/98/2000/Me . You can install the information file ( .inf) in order to select your Philips monitor from "Monitor" dialog box in Windows 95/98/2000/Me to activate Plug & Play application. The installation procedure...
  • Page 90 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Power management function is not active Verify the PC is compliant wit h VESA. In case all of the video signals of PC are not off, power management function is not active normally.
  • Page 91 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page A buzzing sound when powering on This sound is caused when the auto degaussi ng circuit is active. This buzzing sound is normal when the monit or is first turned on. This sound may be louder during the winter months and during initial power on.
  • Page 92 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page NO POWER / LED is off Is cabinet of monitor damaged being dropped? The monitor may have become 1. Is the correct AC power cord faulty due to excessive shock. connected? 2.
  • Page 93 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Color has irregularity Have you changed the Did you adjust the red, tilt or swivel angle green, and blue colors? of the monitor? Press OK " " button Select "EXTRA CONTROLS" Are there any stray fields such as magnetic and Select "RESET TO FACTORY speaker near the monitor?
  • Page 94 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Picture distortion is not adjusted normally. Is it possible to make adjustment by using the On Screen Display ? Press "OK" button, then bring up "MAIN CONTROLS" window. Adjust Horizontal, Vertical or Shape. Is picture Press the OK button...
  • Page 95 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Picture is not stable 1. No picture is displayed for a few s econds in changing resolution (in changing display pixels ) such as picture disappearing in a moment, etc.. Thi s is normal function to mask unstability in c hanging picture.
  • Page 96 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Need to change display size and adjust distortion Adjust each resolution according to user's guide.
  • Page 97 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Color Patterns visible on the screen Are Moire color fringes visible wit h some images? (e.g. Windows shutdown screen) Moire is the phenomenon interference fringes are visible on the screen. It oc curs due to the interference between the regular pattern of vi deo and phosphors layout pattern of CRT, and it i s not a fault but fringe of light and darkness (or colored fringe).
  • Page 98 : Moir is a natural effect or phenomenon of CRT that has the appearance of a wavy pattern é which is repetitive and superimposed on the screen as ripple images. , not just Philips monitor had. These are a few suggestions to help for reducing or minimizing the effect.
  • Page 99 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page OSD MAIN MENU LOCKED Press and hold the OSD menu key for about 10 seconds , until picture displays "OSD MAIN MENU UNLOCKED" Please contact your dealer/reseller for more information.
  • Page 100 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Shimmering/ Jitter/Video Noise Turn on monitor with a display or image for 30 minutes (due to drift). Jitter or Noise still present ? Try moving the monitor to another location to see if problem goes away. Jitter or Noise disappear.
  • Page 101 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Missing Color There are 2 easy ways to determine the Missing color problem. 1. View an image that is supposed to be "White". If one of the colors (RGB) is not functioning. White can not be produced.
  • Page 102 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Color Purity Turn on monitor with a full image for 30 minutes (due to drift). Color Purity or Blotchy or Streaky Press Degauss button (or via the OSD manipulation) or Turn unit "OFF" then "ON" to degauss. Does degaussing resolve ? Note the location of "problem area"...
  • Page 103 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Power management function is not active Verify the PC is compliant with VESA. In case all of the video signals of PC are not off, power management function is not active normally. [Repeat to power on and off (power management).] There are accelerator boards not complied with VESA.
  • Page 104 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page A buzzing sound when powering on This sound is caused when the auto degaussing circuit is active. This buzzing sound is normal when the monitor is first turned on. This sound may be louder during the winter months and during initial power on.
  • Page 105 M32 107E4 GS_3 Go to cover page CustoMax CustoMax is proprietary Philips software that allows user to control parameter (e.g. Size , Color , Geometry ) in place of the buttons on the front of the monitor. To install and run the CustoMax., you must have a USB compatible system and have a USB connection on the rear of your monitor.
  • Page 106 WYSIWYG (what you see is what you get ) . The Colorific software is the property of Sonnetech ,Ltd. Only certain Philips monitor Models are equiped with the software. If you have special interesting , please hit the web site "http:\www.colorific.com".
  • Page 107 PC OEMs. USB 2.0 : Drafted by Compaq, Hewlett Packard, Intel, Lucent, Microsoft, NEC and Philips, USB Specification version 2.0 will increase device data throughout up to 480Mbps, 40 times faster than USB 1.1 devices.
  • Page 108 General Troubleshooting Guide M32 107E4 GS_3 Go to cover page Picture too Large or Small : Reset monitor via OSD menu maniputlation : Adjust the Horz(width) and.or Vert size (height) in the On Screen Display. : Change monitor timing to work at the recommended resolution. Please contact your dealer/reseller for more information.

Table of Contents