Table of Contents
Advertisement
Quick Links
Slim Multisensor PST02-A/B/C
The slim multisensor PST02 has PIR, door/window, temperature and
illumination, 4 sensors function in one, based on Z-Wave
It is the Z-Wave
TM
plus product, it support the security, OTA... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
TM
technology.
TM
technology. Z-Wave
TM
is a wireless
TM
500 series chip, when your Z-Wave
TM
500 series devices. The
Concurrent multi-channel support reduces external interference.
•
Better RF range, improve about 10 meters in indoor.
•
Support 100 Kbps transmit speed, speed up communication.
•
Function Compare A/B/C
PST02-A
PST02-B
PST02-C
Add to/Remove from Z-Wave
There are two tamper keys in the device, one is in the back side,
another is in the front side. Both of them can add, remove, reset or
association from Z-Wave
In the first time, add the device into the Z-Wave
sure the primary controller is in the add mode. And then power on the
device, just take out the insulation Mylar in the back side of the device.
The device will auto start the NWI (Network Wide Inclusion) mode. And
it should be included in 5 seconds. You will see the LED light ON one
second.
TM
network
Notice: Including a node ID allocated by Z-Wave
"Add" or "Inclusion". Excluding a node ID allocated by Z-Wave
Controller means "Remove" or "Exclusion".
TM
1
PIR
Temperature Illumination
Door/Window
V
V
V
V
TM
Network
TM
network.
TM
V
V
V
V
V
V
network. First, make
TM
Controller means
TM
Advertisement
Table of Contents
Related Manuals for Z-Wave PST02-A
Summary of Contents for Z-Wave PST02-A
- Page 1 Z-Wave is a wireless communication protocol designed for home automation, specifically to In the first time, add the device into the Z-Wave network. First, make remotely control applications in residential and light commercial sure the primary controller is in the add mode. And then power on the environments.
-
Page 2: Function Description
Function from Z-Wave Controller. 1. Have Z-Wave Controller entered inclusion mode. Notice 1: Always RESET a Z-Wave device before trying to add it to a 2. Pressing tamper key three times within 1.5 seconds Z-Wave network to enter the inclusion mode. - Page 3 device will unsolicited to send the “Sensor Multilevel Report” to the Notification Type: Home Security (0x07) nodes in the group 1. Event: Motion Detection, Unknown Location (0x08) Sensor Type: Temperature (0x01) Sensor Binary Report (V2) Note: To disable this functionality by setting the configuration N0.5 bit5 Sensor Type: Motion (0x0C) to 1.
-
Page 4: Power Up Procedure
It could be changed by setting the configuration NO. 13. Notice: The configuration NO. 10, 11, 12 and 13 could be setting to The device support the Z-Wave firmware update via OTA. zero to disable the auto report. And the configuration NO. 20 could... -
Page 5: Security Network
Security Network When the event triggered, normally the LED won't indicated, unless the battery is in the low level, the LED will flash once. But in the “Test The device support the security function. When the device included Mode” the LED also will light ON one second. with a security controller, the device will auto switch to the security mode. -
Page 7: Battery Installation
Battery Installation When the device report the low battery message. The user should replace the battery to new one. The battery type is CR123A, 3.0V. The way to open the front cover please follow below steps. 1. Using a tool to press the 1-1 position, to release the cover. 2. -
Page 8: Installation
After finish the test and decide to fix, then you can remove tape A, and mounting the sensor by using tape B. The tamper key will pressed and 1. In the first time, add the device into the Z-Wave network. First, let the sensor enter normal mode. - Page 9 Name Description Name Description Def. A B C Def. A B C Valid Valid Setting the BASIC command value to Operation mode. Using bit to control. turn on the light. The 0xFF(-1) means Caution: The value is unsigned byte, the range is from 0x00 ~ 0xFF. turn on the light.
- Page 10 Name Description Name Description Def. A B C Def. A B C Valid Valid Mult- Multisensor function switch. Using bit Notice: If bit2 is zero, this setting is Sensor to control. useless. Function Caution: The value is unsigned byte, Notice: If the configuration No.9 is Switch the range is from 0x00 ~ 0xFF.
- Page 11 Name Description Name Description Def. A B C Def. A B C Valid Valid Bit6: Disable to report battery state door/window state. when the device triggered. (1:Disable, Time The default value is 12. The tick time 0:Enable) can setting by the configuration No.20.
-
Page 12: Z-Wave Supported Command Class
“Illumination Report” section. Minimum 40 meters indoor, 100 meters outdoor line of sight. Operating Temperature: -10 C ~ 40 Z-Wave Supported Command Class For indoor use only. COMMAND_CLASS_ZWAVEPLUS_INFO_V2 Specifications subject to change without notice due to continuing COMMAND_CLASS_BATTERY product improvement. -
Page 13: Fcc Interference Statement
FCC Caution: Any changes or modifications not expressly approved by resources. To return your used device, please use the the party responsible for compliance could void the user's authority to return and collection systems or contact the retailer where operate this equipment. the product was purchased.