Table of Contents
Advertisement
Quick Links
Ea
southbend
A MIDDLEBY COMPANY
IMPORTANT
FOR FUTURE REFERENCE
Please complete this information
and retain this manual for the life
of the equipment.
MODEL #
SERIAL #
DATE PURCHASED
i
OWNER'S MANUAL
INSTALLATION
USER'S GUIDE
SERVICE
PARTS
INFRA-RED
CHEESE MELTERS
MODELS:
CM-3lC; CIU-36; CM-32; CM-S-60
CM-mPC, cNl=3lw, CMal, CM-3lP
CMeoc, cM-64,cM-60=60
CNMOPC,
CM4OW, CM-60, CM-6OP
These instructions should be read
thoroughly before atterrpting instaMion. in&Won
and Start Up should be petformd by a qualified service techridan. The Mariutacturer,
Southbend (1100 Old HoneyaRt FM., Fuquay-Varina, hbrih Camfina 2Z26), infomrs you
~atunlessthe.~ninstnrctionsfortheabove~SwthbendFHodud~
~andperformedbyaquatifisd~technician,(apelsan~encedinand
krmhdgeable
aweming
the instalWon of cofnmefcial gas.aWof ektrkal
oook@
equipment) then the terms and conditions of the Manufachner's Limited warranty will be
rendefedvoidandnowanantyofanykindshaUapply.
If the equipment has been changed, attered, modified or repaired by other than a
quaiified sewice technician during or after the 12~mordh limited warranty period, then
themanufadurershan~beCaMefotanyindde~orconsequentiald;unagestoany
person or to any property which may result from the use of the equipment thereafter.
Some States do not allow the exclusion or limitation of incidental or consequential
~~,so~e~~li~orexdusiontheretomaynot~toyou.
Intheeve~~youhaveanypuestionsconcemingtheinstal(ation,use,care,orsenriceof
the pfocm, write Customer Service Department, Southbend, 1100 Old Honeycult Rd,
Fuquay-Vartna, North Camha 27526.
MFRAIRED
CHEESE MELTERS
(Manual Section BR)
Advertisement
Table of Contents
Related Manuals for Southbend CM-31
Summary of Contents for Southbend CM-31
- Page 1 OWNER’S MANUAL CHEESE MELTERS MODELS: These instructions should be read and Start Up should be petformd by a qualified service techridan. The Mariutacturer, Southbend (1100 Old HoneyaRt FM., Fuquay-Varina, hbrih Camfina 2Z26), infomrs you ~atunlessthe.~ninstnrctionsfortheabove~SwthbendFHodud~ ~andperformedbyaquatifisd~technician,(apelsan~encedinand krmhdgeable aweming equipment) then the terms and conditions of the Manufachner’s Limited warranty will be rendefedvoidandnowanantyofanykindshaUapply.
- Page 2 Z!EIS RWO2’Ui@l7ON FoRYouRsAEETY TEE LOCAL wIuBEvoIDIR souTHBENDBlEPLA~ equipment mefiial e00king Cqmration. Each piece of Southbend through laboratory end field With proper ca,m and field equipment. Schwank cfmmictilehumm To BE FOLLOWED m S&ALL GAS COMPANY OR GAS PAaTs 1lOOOklHOMyCiJItROild Fquay.NC27526...
- Page 3 INSTALLATION FRONT VEW END VIEW ClFn&CS3lP (Upper gas connection I”i--l RLiJ COUNTER UNITS CM-3lC&CM-3lPC (Upper gas comeion DIMENSIONS: CM-31 ?4’/$ CMMP CMCMC SPECIFICATIONS mj END VIEW cNbOacN-6w not mfaitablc on W-31P tk chbmop~ not mdable on C%3lPC & YooEL9 CM6OP...
-
Page 4: Installation
INSTALLATION WARNING: THESE PERSONNEL OR WARRANTY WILL BE VOIDED. THE UNiT, WHEN INS’T%LLXD, MUSI’ CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL MS CODE, ANSI 2!2!23.1-Latest Edition. CANADIAN INSTALLATION INSTALLATION CODE, CODE CAN/CGA-B149.2 PROPANE INSTALLATION Serial plate located on the top of the unit at the hnt towards the right, indicates the type of gas your unit is equipped to burn, Do Not connect to any other gas type. - Page 5 NOTE: No additional clearance from the sides and back is required for service, as the units are serviceable from the front. E2iHAUST FANSAND CANOPIES: Canopies are set over ranges, ovens, etc., for ventilation purposes. It is recommended that a canopy extend 6”...
- Page 6 INSTALLBTION A I” NPT line is provided at the rear for the connection. Each unit is equipped with an internal pressure regulator which is set propane gas. Use 1/8” pipe tap on the burner manifold for checking pressure. An adequate gas supply is imperative. Undersized or low pressure lines will restrict the vohrme of gas requked for satisfactory perhonnauce.
- Page 7 Never attach the pass thru unit, Model CM3lP, INSTALLATION MUST BE FOLLOWED WILL BE VOIDED. All Cheese Melters are shipped with rack guide assemblies packaged in the crate. They are easily assembled to each side as shown above. Rack guides should be removed periodically for cleaning.
- Page 8 B should be positioned so that the bottom flange is flush with the unit bottom when lllOunted. Mount wall mount assembly securely to the wall in the desired location. Liftunit andplace~eonTiato~partafrearmountingpocket.Positionunit fromrighttoleftalld Rocf3ed with gas connections as discus& INFRARED CHEESE MELTERS SECIION ONE - INsTc\LLATIoN MODEL NO. CM31W FOR MOUNTING CHEESE USING CM-W-31 WALL MOUNT l/4”...
-
Page 9: Installed Position
WARNING: FOR AN APPLIANCE SHALL BE MADE WITB A CONNECTOR TEIAT COMPLIES WITH TEE STANDARD FOR CONNECTORS FOR MOVABLE GAS APPLIANCES, QUlCX-DISCONNECT MS7 AND A QUICK-DISCONNECT DEVICES FOR USE ADDENDA, Z21.41a-1981, ZZ1.41b-1983 MUST BE PROVIDED TO IJMXT THE DEPENDING ON THE CONNECTOR ASSOCIATEDPIPlNGTOIJMITTFIEAPPLL4NCEMOVEMENT. - Page 10 INSTALLATION DIAGRAM 32 IN. SECTIONAL 1. Determine method of gas piping and remove pipe plug fkom unit. 2. Hanger bracket “B” is attached to unit sA” at the &tory unless ordered otherwise. 3. Lift unit with hanger bracket attached and place banger over riser support “c” and fasten with (3) slotted hex head sheet metal screws.
- Page 11 WARNING FORANAPPUANCE SHALLBEMADEWITHACONNECTORTHATCOMPIJES CONNECTORS FOR MOVABLE GAS APPIJANCES, MI37 AND A QUICK-DISCONNECI’ FOR QUICK-DISCONNECT DEVICES FOR USE WIl’!E GAS FUEL, ANSI 221.41-1978, AND ADDEND& 221Ala-1981,221.41b-1983 MUST BE PROVIDED TO LIMIT THE MOVEMENT DEPENDING ON TBE CO~CTOR ASSOCIATEDPIPINGTOLIMITTEIEAPPLLWcEMOVEMENT. IJ? DISCONNECTION WARNING: THE APPIJANCE FOR CLEANING,EI’C,RECONNECT~WHENTBEAPPIJANCEIS MOVEDTOITSORIGINAU,YINSTALLEDPOSITION.
- Page 12 INSTALLATION DIAGRAM Determine method of gas piping and remove pipe plug from unit. Hanger bracket “B” is attached to unit at the factory unless ordered otherwise. Lift unit with hanger bracket attached and place hanger over riser support “C and fasten with (3) slotted hex head sheet metal screws. Unit should be centered on riser. FastenbottombaclrofunittotheFiserwiththetwosheet holesintheb~oftheunitthroughrearofriser.
- Page 13 INSTALLATION MODEL NO. CM36 DIAGRAM FOR INSTALUl4G REAR PANEL AND ANGLES AFlXR CHEESE METLER IS MOUNTED TO 36 IN. CAFE RANGE RISER. 1. Install rear panel “A” and an&s ‘T” to rear ofriser assembly with screw locations shown. Match drill 9164 dia. holes where needed in riser and range body. 2.
- Page 14 CAUTION: ONLYNON~OMBU lIlM!ls.. ~~~OMooMBUslzBLE~U~ONsHow1vONPAGE2. NEVER attach the pass tbru unit, Model CM-GOP, directly to a wall. WFRA-RED CHEESE MELTERS SECTIONONE-lNSTALUllON PAGE 12 AND DIAGRAMS ....SECTION I,...
- Page 15 DIAGRAM FOR MOUNTING USING CMWa Wall mount consists of the following A. (1) Top Bracket - T B. (1) Bottom Bracket - B C. (1) Right Side Bracket - B D. (1) Left Side Bracket - L E. (1) Right Filler - FR F.WLeft.Filler-FL G.
- Page 16 INSTALLATION WARNING FOR AN APPIlLGNcE SHALT., BE MADE WITH A CONNECTOR FOR CONNECTORS 6.16-MS7 AND A QUICK-DISCONNECT STANDARD FOR QUICK-DI!XONNECT 221.41-1978, AND ADDENDA, ADEQUATE MEANS APPLIANCE WITHOUT DISCONNECT DEVICE MOVEMENT. WAR&IN& IF DISCONNECTION TBE APPLTANCE FOR tXZANlNG, MOVED TO ITS ORIGINALLY cMs-64sEcTIoNAL64lN.RI8ERToTwoRANGEs 1.
- Page 17 DIAGRAM 64 IN. SECTIONAL 1. Determine method of gas piping and remove pipe plug from unit. Hanger brackets “B” are attached to unit ‘A” at the factoq unless ordered otherwise. 3. LiR unit witi banger brackets attached and place hangers over riser support “Cy line up holes and fasten with (6) slotted hex head sheet metal screws.
- Page 18 INSTALLATION WARNING FORANAPPLIANCE SHALL BE MADE WITH A CONNECTOR FOR CONNECTORS FOR MOVABLE 6.16-MS7 AND A QUICK-DISCONNECT STANDABD FOR QUICK-DISCONNECT 221.41-1978, AND ADDENDA, ADEQUATE MEANS MUST BE PROVIDED APPLIANCE WITHOUT DISCONNECT DEVICE OR ITS ASSOCLATED MOVEMENT. WARNING IF DISCONNECTION THEAPPLk3NCEFOR MOVED To ITS OBIGINALLY YNSTATXXD POSITION.
- Page 19 DIAGRAM FOR MOUNTING 60-314 IN. CAFE RANGE RISER NO. CMCXo. NOTE: Most 60-314 * riser assemblies are shipped &om the factory preassembled to the range. If not however, follow the mounting method depicted in the diagram The following in&n&ions be followed to mount a Cheese Melter to a CMG60,60-3/4 ” riser assembly. 1.
- Page 20 DEPENDING ON THE CONNECTOR PIPING OF T[lBIs ZtEsTRAINT ETC., RECONNECT POSITION. MODEL NO. CM-31.60 DIAGRAB5FORMOUNTINGCEERSEMELTERTO 6@3/4 IN. CAFE RANGE RISER NO. MRK-30. unit “A” at the factory unless ordered otherwise. as shown on range serial plate, supersede WITH THE STANDARD...
-
Page 21: Limited Warranty
Should any part thereof become defective as a result of nomral use within the period and limits defined below, then at the option of Southbend such parts will be repaired or replaced by Southbend or its Autho- rized Service Agency. -
Page 22: Operation
All Cheese Melters are shipped with xack guide assemblies packaged in the crate. They are easily assembled to each side as shown above. Rack guides should be removed periodically for cleaning. PRODUCTS... -
Page 23: Burner Removal
BURNERREMOVAL: 1. Remove 12 slotted hex head screws fi-om top panel. Remove top panel. 3. Disconuect gas supply tube to burner. Remove tube. 5. Remove screws from small filler panel at left end of burner. 6. Remove panel and insulatior~ 7. -
Page 24: Maintenance
)) MAINTENANCE WARNING: AJMUSTMEN’B T33cHNIcIANwHoIsExPERIENcEDINANDENo-LE THE OPERATION OF COMMERCIAL A!3SUREYOURCONFIDENCE,CON’IACI’YOURAUTHORIzED RELIABLE SERVICE, DEPENDABLE GENUINE FACTORY PARTS. WARNING DIscoNNEcrpowEBERoM~P~~EQuLppED~COrvvEcrrON TYPE OVEN HAVING A CHEESE MELTER CLEANINGORSERS’ICING,IFAPPLICABI3. MAl[NTENANcE: l.Kaepbottomofunitcleanatalltimes. Daily A Remove rack and wash daily. B. Remove entire side liuings, to which the rack slides are fastened, by lifting up and inward. - Page 25 INFRA-RED CHEESE MELTERS GENERAL: When any difficulty arises it is always a good idea to check that the unit has been connected to the gas supply type and voltage for which it was supplied. This can be done by examining the serial plate located on the top of the unit at the front towards the right.
- Page 26 VOID THE wARR4NTY The serial plate is located on the top of the unit at the front on the right. Replacement parts may be ordered either through a Southbend Authorized Parks Distributor or a Southbend Authorized Service Agency. When ordering parts, please supply the Model Number, Serial Number, Part Number, Description, plus Finish, Type of Gas and Electrical Characteristics, as applicable.
- Page 27 PARTS LIST FOE CM=6OPC, CM-6OW, CM-60, CM-cioP Gas (1163675) @To. 53) Distributor please consult Southbend Parts Department for a&stance. Stainless Right Side Black LetI Side Black Right Side Black Right Body Side (Pass Thru) Black Left Body Side (Pass Thru)
- Page 28 CHEESE MELTERS A product with the Southbend name incorporates the best in durability and low maintenance. We all recognize however, that replacement parts and occasional professional service may be necessary to extend the useful life of this unit. When service is needed, contact a Southbend Authorized Service Agency, or your dealer.
Need help?
Do you have a question about the CM-31 and is the answer not in the manual?
Questions and answers