C Group: Intelligent Terminal Functions - Hitachi SJ700 Series Manual

Variable frequency drive

Hide thumbs Also See for SJ700 Series:

Instruction manual (46 pages)

Manual (41 pages)

Software manual (15 pages)

Table Of Contents

Table of Contents

Code

Function Name

b112

Free-setting V/f frequency (7)

b113

Free-setting V/f voltage (7)

b120

Brake control enable

b121

Brake wait time for release

b122

Brake wait time for acceleration

b123

Brake wait time for stopping

b124

Brake wait time for confirmation

b125

Brake release frequency setting

b126

Brake release current setting

b127

Braking frequency

b130

Overvoltage suppression enable

b131

Overvoltage suppression level

Acceleration and deceleration rate

b132

at overvoltage suppression

b133

Overvoltage suppression propotional gain

b134

Overvoltage suppression Integral time

(*1) 4000HF:0.0 to 120.0(Hz) (*2)4000HF:0.00 to 99.99, 100.0 to 120.0(Hz)

●C GROUP: INTELLIGENT TERMINAL FUNCTIONS

Code

Function Name

C001

Terminal [1] function (*1)

C002

Terminal [2] function

C003

Terminal [3] function (*1)

C004

Terminal [4] function

C005

Terminal [5] function

C006

Terminal [6] function

C007

Terminal [7] function

C008

Terminal [8] function

C011

Terminal (1) active state

C012

Terminal (2) active state

C013

Terminal (3) active state

C014

Terminal (4) active state

C015

Terminal (5) active state

C016

Terminal (6) active state

C017

Terminal (7) active state

C018

Terminal (8) active state

C019

Terminal FW active state

Terminal (11) function

C021

C022

Terminal (12) function

Terminal (13) function

C023

C024

Terminal (14) function

Terminal (15) function

C025

C026

Alarm relay terminal function

C027

FM signal selection

C028

AM signal selection

C029

AMI signal selection

(*1) When the emergency stop function is enabled (SW1 = ON), "18" (RS) and "64" (EMR) are forcibly written to parameters "C001" and "C003",

respectively. (You cannot arbitrarily write "64" to "C001".) If the SW1 signal is turned off and then turned on, "no" (no assignment) is set in parameter "C003".

(*2) L700 series: The function is not provided. (*3)1850HF,2200HF,3150HF and 4000HF:The function is not provided.

Monitored data or setting

0.0 to 400.0 (Hz) (*1)

0.0 to 800.0 (V)

00 (disabling), 01 (enabling)

0.00 to 5.00 (s)

0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)

0.0 to 2.00 x "rated current"

0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)

00 (disabling the restraint), 01 (decelerating and stagnating), 02 (enabling acceleration)

330 to 390 (V) (200 V class model), 660 to 780 (V) (400 V class model)

0.10 to 30.00 (s)

0.00 to 2.55

0.000 to 9.999 / 10.00 to 63.53 (s)

Monitored data or setting

01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting), 03 (CF2: Multispeed 2 setting),

04 (CF3: Multispeed 3 setting), 05 (CF4: Multispeed 4 setting), 06 (JG: Jogging), 07 (DB:

external DC braking), 08 (SET: Set 2nd motor data), 09 (2CH: 2-stage

acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT: external trip), 13 (USP:

unattended start protection), 14: (CS: commercial power source enable), 15 (SFT: software

lock), 16 (AT: analog input voltage/current select), 17 (SET3: 3rd motor control), 18 (RS:

reset), 20 (STA: starting by 3-wire input), 21 (STP: stopping by 3-wire input), 22 (F/R:

forward/reverse switching by 3-wire input), 23 (PID: PID disable), 24 (PIDC: PID reset),

26 (CAS: control gain setting), 27 (UP: remote control UP function), 28 (DWN: remote

control DOWN function), 29 (DWN: remote control data clearing), 31 (OPE: forcible

operation), 32 (SF1: multispeed bit 1), 33 (SF2: multispeed bit 2), 34 (SF3: multispeed bit

3), 35 (SF4: multispeed bit 4), 36 (SF5: multispeed bit 5), 37 (SF6: multispeed bit 6),

38 (SF7: multispeed bit 7), 39 (OLR: overload restriction selection), 40 (TL: torque limit

enable), 41 (TRQ1: torque limit selection bit 1), 42 (TRQ2: torque limit selection bit 2),

43 (PPI: P/PI mode selection), 44 (BOK: braking confirmation)(*2), 45 (ORT:

orientation)(*2), 46 (LAC: LAD cancellation), 47 (PCLR: clearance of position deviation)(*2),

48 (STAT: pulse train position command input enable)(*2), 50 (ADD: trigger for frequency

addition [A145]), 51 (F-TM: forcible-terminal operation), 52 (ATR: permission of torque

command input)(*2), 53 (KHC: cumulative power clearance), 54 (SON: servo-on)(*2),

55 (FOC: pre-excitation)(*2), 56 (MI1: general-purpose input 1), 57 (MI2: general-purpose

input 2), 58 (MI3: general-purpose input 3), 59 (MI4: general-purpose input 4), 60 (MI5:

general-purpose input 5), 61 (MI6: general-purpose input 6), 62 (MI7: general-purpose input 7),

63 (MI8: general-purpose input 8), 64 (EMR: Emergency stop)(*1), 65 (AHD: analog command

holding), 66 (CP1: multistage position settings selection 1 )(*2), 67 (CP2: multistage position

settings selection 2)(*2), 68 (CP3: multistage position settings selection 3)(*2), 69 (ORL:

Zero-return limit function)(*2), 70 (ORG: Zero-return trigger function)(*2), 71 (FOT: forward drive

stop)(*2), 72 (ROT: reverse drive stop)(*2), 73 (SPD: speed / position switching)(*2), 74 (PCNT:

pulse counter), 75 (PCC: pulse counter clear), no (NO: no assignment)

00(NO) / 01(NC)

00 (RUN: running), 01 (FA1: constant-speed reached), 02 (FA2: set frequency overreached), 03 (OL:

overload notice advance signal (1)), 04 (OD: output deviation for PID control), 05 (AL: alarm signal),

06 (FA3: set frequency reached), 07 (OTQ: over-torque), 08 (IP: instantaneous power failure), 09 (UV:

undervoltage), 10 (TRQ: torque limited), 11 (RNT: operation time over), 12 (ONT: plug-in time over),

13 (THM: thermal alarm signal), 19 (BRK: brake release)(*2), 20 (BER: braking error)(*2), 21 (ZS: 0

Hz detection signal), 22 (DSE: speed deviation maximum)(*2), 23 (POK: positioning completed)(*2),

24 (FA4: set frequency overreached 2), 25 (FA5: set frequency reached 2), 26 (OL2: overload notice

advance signal (2)), 27 (Odc: Analog O disconnection detection), 28 (OIDc: Analog OI disconnection

detection), 29 (O2Dc: Analog O2 disconnection detection), 31 (FBV: PID feedback comparison),

32 (NDc: communication line disconnection), 33 (LOG1: logical operation result 1), 34 (LOG2: logical

operation result 2), 35 (LOG3: logical operation result 3), 36 (LOG4: logical operation result 4),

37 (LOG5: logical operation result 5), 38 (LOG6: logical operation result 6), 39 (WAC: capacitor life

warning)(*3), 40 (WAF: cooling-fan speed drop), 41 (FR: starting contact signal), 42 (OHF: heat sink

overheat warning), 43 (LOC: low-current indication signal), 44 (M01: general-purpose output 1),

45 (M02: general-purpose output 2), 46 (M03: general-purpose output 3), 47 (M04: general-purpose

output 4), 48 (M05: general-purpose output 5), 49 (M06: general-purpose output 6), 50 (IRDY: inverter

ready), 51 (FWR: forward rotation), 52 (RVR: reverse rotation), 53 (MJA: major failure), 54(WCO:

window comparator O), 55(WCOI: window comparator OI), 56 (WCO2: window comparator O2)

(When alarm code output is selected for "C062", functions "AC0" to "AC2" or "AC0" to "AC3" [ACn:

alarm code output] are forcibly assigned to intelligent output terminals 11 to 13 or 11 to 14,

respectively.)

00 (output frequency), 01 (output current), 02 (output torque), 03 (digital output frequency), 04 (output

voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 08 (digital current

monitoring), 09 (motor temperature), 10 (heat sink temperature), 12 (general-purpose output YA0)

00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06

(electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 11

(output torque [signed value]), 13 (general-purpose output YA1)

00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06

(electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 14

(general-purpose output YA2)

［◯= Allowed

= Not permitted］

Default Setting

Setting

SJ700

during operation

L700

(allowed or not)

-FE(CE) -FU(UL)

-F(JP)

0.0

0.00

Rated current x 1.00

0.00

380/760

1.00

0.50

○

0.060

［◯= Allowed

= Not permitted］

Default Setting

Setting

SJ700

during operation

L700

(allowed or not)

-FE(CE) -FU(UL)

-F(JP)

18(RS)

16(AT)

06(JG)

03(CF2)

11(FRS)

02(CF1)

09(2CH)

01(RV)

03(CF2)

13(USP)

03(CF2)

06(JG)

02(CF1)

11(FRS)

01(RV)

13(USP)

01(FA1)

00(RUN)

03(OL)

07(OTO)

40(WAF)

05(AL)

Change

during operation

(allowed or not)

○

Change

during operation

(allowed or not)

○

Table of Contents

This manual is also suitable for:

L700 series

C Group: Intelligent Terminal Functions - Hitachi SJ700 Series Manual

Related Manuals for Hitachi SJ700 Series

Related Content for Hitachi SJ700 Series

This manual is also suitable for:

Table of Contents