JVC KW-X850BT Instruction Manual page 28

Audio Settings
[PRO EQ] Adjusts your own sound settings for each source.
• The settings are stored to [USER] in [PRESET EQ].
• The settings made may affect the current settings of [EASY EQ].
[62.5HZ]
[LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
[ON]: Turns on the extended bass. ; [OFF]: Cancels.
[100HZ]/[160HZ]/[250HZ]/[400HZ]/[630HZ]/[1KHZ]/[1.6KHZ]/[2.5KHZ]/[4KHZ]/
[6.3KHZ]/[10KHZ]/[16KHZ]
[LEVEL –09] to [LEVEL +09] ([LEVEL 00]): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
[Q FACTOR] [1.35]/[1.50]/[2.00]: Adjust the quality factor.
[AUDIO CONTROL]
[BASS BOOST] [LEVEL +01] to [LEVEL +05]: Selects your preferred bass boost level. ;
[OFF]: Cancels.
[LOUDNESS] [LEVEL 01]/[LEVEL 02]: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; [OFF]: Cancels.
[SUB.W [SPK-OUT]*2
LEVEL]*1
[PRE-OUT]
20
ENGLISH
(Not applicable when 3-way crossover is selected.)
[SUB.W 00] to [SUB.W +06] ([SUB.W +03]): Adjusts
the output level of the subwoofer connected via speaker
lead. (Page 33)
[SUB.W –50] to [SUB.W +10] ([SUB.W 00]): Adjusts
the output level of the subwoofer connected to the
lineout terminals (SW) through an external amplifier.
(Page 33)
[SUBWOOFER [ON]: Turns on the subwoofer output. ; [OFF]: Cancels.
SET]
[FADER] (Not applicable when 3-way crossover is selected.)
[POSITION R15] to [POSITION F15] ([POSITION 00]): Adjusts the front
and rear speaker output balance.
[BALANCE]*3 [POSITION L15] to [POSITION R15] ([POSITION 00]): Adjusts the left and
right speaker output balance.
[VOLUME [LEVEL –15] to [LEVEL +06] ([LEVEL 00]): Presets the initial volume level
ADJUST] of each source by comparing to the FM volume levels. (Before adjustment,
select the source you want to adjust.)
[AMP GAIN] [LOW POWER]: Limits the maximum volume level to 25. (Select if the
maximum power of each speaker is less than 50 W to prevent damaging
the speakers.) ; [HIGH POWER]: The maximum volume level is 35.
[SPK/PRE OUT] (Not applicable when 3-way crossover is selected.)
Depending on the speaker connection method, select the appropriate
setting for the desired output. (See "Speaker output settings" on
page 21.)
[SPEAKER SIZE] Depending on the crossover type you have selected (see [X ' OVER TYPE]
on page 21), 2-way crossover or 3-way crossover setting items will be
shown. (See "Crossover settings" on page 22.)
[X ' OVER]
By default, 2-way crossover type is selected.
[DTA SETTINGS]
For settings, see "Digital Time Alignment settings" on page 24.
[CAR SETTINGS]
*1 Displayed only when [SUBWOOFER SET] is set to [ON].
*2 For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W].
(Page 21)
*3 This adjustment will not affect the subwoofer output.