Owners 00000 Garage Door Opener Model 139.53315SR ", Model 139.53415SR- Model 139.53615SR Model 139.53625SR Model 139.53699SR FASTEN THIS MANUAL NEAR THE INSTALLATION, PERIODIC CHECKS REQUIRED TO INSURE SATISFACTORY FOR RESIDENTIAL USE ONLY, ,,NIU = , I ... anual 1/3HP CONTENTS 1/2HP Safety Rules ...
Page 2
To avoid serious personal injury from entangle- ment, REMOVE ALL ROPES CONNECTED GARAGE DOOR before garage door opener. DISENGAGE ALL EXISTING LOCKS to avoid damage to garage door. Installation and wiring must be in compliance with your local building and electrical...
Step 5 page 9, DO NOT make ANY further adjustmants_ TRANSMITTER: The 3-function transmitter willoperate more than one garage door opener, if desired. The push buttons may also be used to operate other 53000 and/or53000SR Series devices. The standardtransmitter may be secured to car sun visor with clip provided.
4¥2 6. 3-Function Transmitter: button can activate one or more Light Control and,or down force garage door opener. The opener receiver when preset to activate with LARGE transmitter push button, 7. Emergency Disconnect: manual door operation.
Otherwise, the trolley will hit against the nut when installed (Pg. 7). Tea P_t (End Section) FRONT (TO DOOR) DO NOT RUN THE GARAGE DOOR OPENER UNTIL INSTRUCTED Tee Rail & Attach Cable Pulley Bracket , ,, ,,,,, ='== =,= =,,,,,,,, ,i ,,,= _14"...
Page 7
Assembly iiii AS A TEMPORARY STOP, INSERT A SCREWDRIVER INTO HOLE IN FRONT END OF TEE RAiL AS SHOWN. as s hown 1, At_ch threaded shaft to trolley with tockw_her 2. Slide trolley assembly along rail to screwdriver NOTE: If trolley hits against the nut on Tee rail, center section was attached from wrong side and must be re_sitioned.
Page 8
Assembly iii, ,JIJ,,llJ,lL,II I,,,,,,',, STEP 4 iiii i111 DO NOT REMOVE CHAIN AND CABLE FROM CARTON. Detach cable from side of carton and fasten to trolley with a master link from coin envelope, MASTER LINK PROCEDURE: Push pins of master link bar through loop of cable and hole in front end of trolley (A) as shown°...
Page 9
Chin Sprocket noise can result or too tight, .,-.--- 1/2 Inch CAUTION: OF YOUR GARAGE DOOR OPENER OF YOUR GARAGE DOOR OPENER, STICKING OR BINDING DOORS MUST BE REPAIRED. THE GARAGE DOOR, BRACKETS AND THEIR HARDWARE PERSONAL INJURY. DO NOT ATTEMPT...
installation i,! ,i iiii i, ,i,,i i, iiii1,11 Position STEP 1 installation procedures vary according tions which apply to your door as tllustratedo THE HEADER BRACKET MUST BE RIGIDLY FASTENED TO THE HEADER WALL. REINFORCE THE WALL WiTH 2x4 IF NECESSARY. FAILURE TO COMPLY MAY RESULT IN IMPROPER OPERATION OF SAFETY REVERSE SYSTEM (SEE PAGE 18)+ 1o With the door closed, locate and mark the vertical centerline of garage door.
Page 11
|n3tallation ii H i ml STEP 2 " IIIIIII IIIII ,IlL STEP 3 Position Follow instructions which apply to your door type as illustrated. iiiH lille TO PREVENT DAMAGE TO ALL LIGHTWEIGHT THE OPENER ON THE DOOR_ INSTALLATION SECTIONAL & ONE-PIECE DOOR WITH TRACK NOTE: A 2x4 is convenient for setting an ideal door- to-Tee rail distance, tt is not necessery where headroom...
Page 12
In.otallation .,,,,,,, STEP 4 THE OPENER CHASSIS MUST BE SECURELY FASTENED Three representative installations or crossed (Fig.2) to provide rigid support, On finished ceilings (Fig.3), attach a sturdy metal bracket (not supplied) ceiling joists before installing opener. PROCEDURE: On EACH side of the opener measure the distance from chassis to the structural supports, Ratten one end of each bracket and bend or twist to fit the fastening angles, Do not bend at the bracket holes.
Page 13
installation u,,,, i,,,. STEP 6 LOCATE WALL PUSH BUTTON (OR ANY ADDITIONAL IS VISIBLE, AWAY FROM DOOR AND DOOR HARDWARE AND OUT OF THE REACH OF CHILDREN, SERIOUS PERSONAL INJURY FROM A MOVING GARAGE DOOR MAY RESULT FROM MISUSE OF THE OPENER.
Page 14
]nstaliation ILLII STEP 7 ...ii INSTALLING LIGHT: Install a 75 watt maximun light bulb in socket as shown° The light will turn on and remafn lit for 4-1/2 minutes when power is connected,, After 4d12 minutes it will turn off_ If light bulb burns out prematurely replace with s bulb specifically packaged for "Garage Door Openers".
Page 15
Installation i,ill STEP 9 TO PREVENT DAMAGE TO LIGHTWEIGHT PANELS), ALWAYS REINFORCE BOARDS OR ANGLE The horizontal brace should be at least 6 feet long. The vertical brace should cover height of top panel. Check with your garage door manufacturer Sectional Header Bracket...
Page 16
nstallation STEP 10 Connect Follow SECTIONAL Make sure garage door is closed tighL outer trolley back to the center of inner FIG A: Fasten straight door arm section to outer trolley with a clevis pin. Secure the connection with a ring fastener. Fasten curved section to door bracket in the same way_ --h.._'.F m_et...
Adjustment ,u.,imu. ,,,,,1 STEP 1 LIMIT ADJUSTMENT settings regulate the points at which the door will stop when mowng up or down. NOTE: Door STOPS in the UP direction if anything interferes with door travel. Door REVERSES DOWN direction if anything interferes with the door travel (including binding or unbalanced PROCEDURE: To operate opener, press wall push button or transmitter, Run the opener through a COMPLETE...
INJURY FROM A CLOSING GARAGE DOOR. REPEAT TEST AT LEAST do not force the STEP 3 AFTER: OF DOOR ARM LENGTH, CLOSE FORCE OR DOWN LIMIT, OF GARAGE DOOR (INCLUDING OF THE GARAGE FLOOR. OF THE GARAGE DOOR OPENER. i,iii iiii ,lllll,lllllt iii STEP 4 instafl...
Manufactured under Your 53000SR SERIES garage door opener (with RECEIVER 'SR' CODE BUTTON) has been factory set to operate with the LARGE push button on the transmitter, door openers and/or light controls. Instructions...
Antenna extender Service Cente[ Check to be sure antenna on the back panel of opener extends fully downward_ 1 is there a neighbor with a garage door opener using the same frequency Change your code Review page 19 2. Check to be sure that none of the transmitter ptJsh buttons is stuck in the 'down' position 3.
Having a Problem? SITUATION I,H,m DOOR REVERSES NO APPARENT REASON OPENER LIGHT OPENER STRAINS OR MAXIMUM FORCE IS NEEDED TO OPERATE DOOR OPENER MOTOR HUMS BRIEFLY, THEN WON'T WORK OPENER WON'T OPERATE DUE TO POWER FAILURE CHAIN DROOPS OR SAGS i,,ll i ,,, i OPENER NOISE IS DISTURBING...