Related Manuals for HAMPTON BAY Milton 458 412
Summary of Contents for HAMPTON BAY Milton 458 412
- Page 1 458 412 Milton Ceiling Fan Owner’s Manual Milton Ventilador de Techo de 1,32 Manual del Propietario...
- Page 2 Milton by Hampton Bay ®...
-
Page 3: Table Of Contents
Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. The finish of this fan is weather resistant, but over time will Ceiling Fan by Hampton Bay naturally weather and fade. Date Purchased... -
Page 4: Safety Rules
Safety Rules - Read and Save These Instructions To reduce the risk of electric shock, insure electricity has been turned off After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning. upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding All wiring must be in accordance with the National Electrical Code conductor on one side of the outlet box and ungrounded conductor on the... -
Page 5: Unpacking Your Fan
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: LIGHT BAT. Set of blades (5) (wood blades) Fan motor assembly Blade Attachment Hardware (16 Screws, 16 Rubber Washers) Set of blades (5) (Plastic blades) Set of blade bracket (5) Canopy assembly Light kit... -
Page 6: Installing Your Fan
Installing Your Fan Provide Strong Support Figures 1~3 are examples of different ways to Tools Required mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Ceiling Outlet Box Mounting Plate Figure 3 Mounting Options Outlet Box Note: You may need a longer downrod to If there isn't an existing UL listed mounting box,... - Page 7 Hanging the Fan the clevis pin until it snaps into its locked Motor Wires position, as noted in the circle inset of Fig. 6. REMEMBER to turn off the power. Follow the Pin in Locked WARNING Ceiling Canopy Positioon steps below to hang your fan properly. FAILURE TO PROPERLY INSTALL COTTER PIN AS NOTED IN STEP 5 COULD RESULT IN FAN Remove the decorative canopy bottom cover...
- Page 8 Changing the Downrod Installing Fan to UL Listed Outlet Box the Electrical Box (Optional) NOTE: Your fan comes with a 4" downrod WARNING 120V attached to the hanger ball. In addition you have TO REDUCE THE RISK OF FIRE, ELECTRIC Wires been provided with a 6"...
- Page 9 Making the Electrical (Fig. 11) Motor to receiver electrical connec- tions: Connect the black wire from the fan to Code Switch Connections black wire marked "TO MOTOR L". Connect the white wire from the fan to the white wire WARNING Rubber marked "TO MOTOR N"...
- Page 10 Installing the Wall SUPPLY CIRCUIT Outlet Box Switch Wall Plate Transmtter Screws Screws Remember to shut the power off at the circuit Ground breaker or fuse box. Conductor BLACK Disconnect the power and remove the existing Outlet Box wall plate and switch from the wall junction box.
- Page 11 Finishing the Fan WARNING MAKE SURE THE TAB ON THE MOUNTING Installation BRACKET PROPERLY SITS IN THE GROOVE IN THE HANGER BALL BEFORE ATTACHING THE CANOPY TO THE BRACKET BY TURNING THE Tuck connections neatly into ceiling outlet HOUSING UNTIL IT DROPS INTO PLACE. box.
- Page 12 Attaching the Fan Blades Blade Screws with CAUTION Rubber Washers REMOVE THE 5 SCREWS FROM THE MOTOR SUPPORT PLATE, DISCARD THE 5 SCREWS AND MOTOR SUPPORT PLATE. Attach blades to blade arm using the screws and rubber washers provided. (Fig. 15) Start a screw into the blade arm, do not tighten.
- Page 13 Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling Check that all blade and blade arm screws are secure. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades.
-
Page 14: Installing The Light Kit
Installing the Light Kit 6. Restore power and your light kit is ready for CAUTION operations. BEFORE STARTING INSTALLATION, DISCON- NECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. -
Page 15: Operating Your Transmitter
Operating Your Transmitter LIGHT Installing the Battery: Restore power to the ceiling fan and test for proper operation. Install 9 volt battery (not included), to prevent "HI, MED, LOW" buttons: damage to transmitter, remove the battery if not These three buttons are used to set the fan used for long periods. - Page 16 Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc. The Reverse switch is located on the top of motor housing. Slide the switch to the Left for warm weather operation.
-
Page 17: Care Of Your Fan
Care of Your Fan Troubleshooting PROBLEM SOLUTION Here are some suggestions to help you maintain your fan. Fan will not start Check main and branch circuit fuses or breakers. Because of the fan's natural movement, some Check line wire connections to the fan and switch wire connections in connections may become loose. -
Page 18: Specifications
Specifications FAN SIZE SPEED VOLTS AMPS WATTS N.W. G.W. C.F. 0.36 1200 14.35 kgs 16.39 kgs 52” MED. 0.48 3850 2.59’ (31.57 lbs) (36.06 lbs) 0.56 6500 HIGH These are approximate measures. They do not include Amps and Wattage used by the light kit. -
Page 19: Warranty Information
Hampton Bay Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time You must present a copy of the original purchase receipt to obtain warranty of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.