TABLE OF CONTENTS About This Manual ........................3 Warranty Statement ......................4 Safety Information .........................5 Operation of Equipment ......................6 Assembly Attaching The Handle ....................7 Fill Engine With Oil ......................7 Installing The Throttle Wire ................... 8 Fuel Specification ......................8 Operating Your Edger/Trimmer Correct Engine Operation .....................
About This Manual This owner’s manual is considered a permanent part of the edger. It must be available to all of the operators and/or person(s) servicing the edger. Should the unit be resold, this manual must remain with the unit. All information, illustrations, and specifications contained in this manual were in effect at the time of publication.
Warranty Statement This edger/trimmer is warranted for one (1) year from the original date of purchase against defects in material or workmanship, when operated and maintained in accordance with the Owner’s Manual. The Manufacturer will replace or repair, free of charge, any part of the original equipment returned to us or our authorized servicing representative with transportation or postage prepaid and which upon examination shall be defective.
Safety Information Read This Manual Carefully And Thoroughly Before Operating The Edger! Training Carefully and thoroughly read the owner's manual. Allow adequate time to fully understand the controls and operation of the equipment. Never allow anyone to operate the edger that has not read and fully understood the owner's manual.
Operation of Equipment DANGER: GASOLINE IS HIGHLY FLAMMABLE AND EXPLOSIVE. DO NOT ADD FUEL WHILE THE ENGINE IS RUNNING OR IS HOT. KEEP OPEN FLAMES, SPARKS, AND HEAT AWAY FROM THE FUEL AND STORE FUEL IN CONTAINERS SPECIFICALLY DESIGNED FOR THAT PURPOSE. ADD FUEL OUTDOORS ONLY AND IF THE FUEL IS SPILLED, DO NOT START THE ENGINE.
Assembly NOTE: Reference to Left or Right side of the machine is from the operator's position at the handle, facing for-ward. The edger, except the handle and throttle control is fully assembled, packed and shipped in one carton. Attaching The Handle 1.
Installing The Throttle Wire 1. If the throttle cable is not attached tot he engine carburetor, follow the instructions in the engine operating manual. Some throttle cables can not be attached before shipping. Fuel Specification 1. Follow fueling instructions in the engine manual. DANGER: GASOLINE IS HIGHLY FLAMMABLE AND EXPLOSIVE.
Clutch And Depth Lever Settings The clutch and depth lever is used to engage and disengage the drive belt which operates the blade. It is also used to regulate the depth of edging and height of trimming. Starting The Engine 1.
Wheel Positioning The wheel adjusting spacer should be centered between the wheels when edging in the vertical position. Wheels must be in the dual position to the right when edging with cutterhead in an angle position or trimming (horizontal position). DANGER: DO NOT CHANGE THE WHEEL POSITION WHEN THE ENGINE IS RUNNING.
Correct Edger/Trimmer Usage Operation of the Trimmer/Edger DANGER: KEEP ALL SHIELDS IN PLACE. NEVER ATTEMPT TO CLEAR DISCHARGE AREAS OR EDGER/TRIMMER BLADE WITHOUT DISENGAGING THE EDGER/TRIMMER AND STOPPING THE ENGINE. For best results when edging, adjust blade to 20° angle cut and adjust the cutting depth of the blade to within 1/2"...
Blade Maintenance CAUTION: Beware of the cutting edges on the blades. Always wear work gloves when handling blades. Changing Blades 1. Place wrench on the inside of the cutterhead shaft. and a wrench on the blade nut. Turn to loosen nut. Remove outer washer and old blade. 2.
Page 19
TROUBLE SHOOTING Problem Possible Cause Solution Fuel tank empty Fill fuel tank Throttle control not in the choke Move throttle control to choke position Remove spark plug, dry the plug Crank engine with plus Carburetor improperly adjusted removed and throttle in OFF position.
Page 20
TROUBLE SHOOTING Dirt or water in the fuel tank Drain and clean fuel tank Irregular Dirty air filter Replace Running Vent in gas cap and/or Clear carburetor plugged Carburetor idle speed too slow Check and adjust Idles Poorly Spark plug gap too close Check and adjust Dirty air filter Replace...
Warranties should be performed by an authorized Bradley Mowers dealer. All other warranty service requires prior approval. Your product warranty is only valid if this file is completed signed, and returned to Havener Enterprises, Inc. within two weeks of product purchase. See the warranty statement for more details.