Related Manuals for KRESS KG367E Series
Summary of Contents for KRESS KG367E Series
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Cordless Chainsaw KG367E KG367E.X...
-
Page 2: Work Area Safety
ORIGINAL INSTRUCTIONS moment of inattention while operating power tools may result in serious personal injury. PRODUCT SAFETY b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust GENERAL POWER TOOL mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will SAFETY WARNINGS reduce personal injuries. -
Page 3: General Chain Saw Safety Warnings
g) Use the power tool, accessories and tool bits is not contacting anything. A moment of inattention etc. in accordance with these instructions, taking while operating chain saws may cause entanglement into account the working conditions and the of your clothing or body with the saw chain. work to be performed. -
Page 4: Causes And Operator Prevention Of Kickback
while clearing jammed material or servicing may Access to the rotating saw chain (cutting hazards) result in serious personal injury. Unforeseen, abrupt movement of the guide bar n) Recommendation that the first-time user should, (cutting hazards) as a minimum, practise cutting logs on a saw- Flung out of parts from the saw chain (Cutting / horse or cradle. - Page 5 high pressure. use the retreat path planned ( ). Be alert for overhead Warning! Do not use non-rechargeable batteries limbs falling and watch your footing. (See Figure 1) Fig.1 Fig.1 SAVE THESE INSTRUCTIONS Fig.1 Instructions concerning the proper techniques for basic felling, limbing, and cross-cutting 50mm 50mm...
- Page 6 underbuck) (1). Then make the finished cut by Fig.6 overbucking (2) to meet the first cut. Fig.4 Fig.4 When the log is supported on both ends, as illustrated in Figure 5, cut 1/3 the diameter from the top (overbuck) (1). Fig.5 SYMBOLS Then make the finished cut by underbucking (2) the lower...
- Page 7 ABN: Australian Business Number. By this number, Wear protective gloves business information such as entity type, status, business location etc. can be found at website http://abr.business.gov.au. ABN of Positec Australia Pty Limited is 14 101 682 Waste electrical products must not be 357.
- Page 9 Kink...
- Page 10 3-5mm...
- Page 11 Click! Click!
- Page 12 Injecting grease to lubricate...
-
Page 13: Component List
COMPONENT LIST Chain gauge 1.1 mm Adaptive Chain CHAIN Oregon/90PX052G type GUIDE BAR Adaptive Bar Oregon/144MLEA041 type CHAIN BRAKE LEVER (HAND GUARD) Machine Weight FRONT HANDLE 4.3 kg (bare tool) BATTERY PACK RELEASE BUTTON* **X=1-999, A-Z, M1-M9 there are only used for different LOCK-OUT BUTTON customers, there are no safe relevant changes between REAR HANDLE... -
Page 14: Intended Use
2. Place the Chainsaw on a solid, level surface. should be done by using one hand to raise the chain 3. Use only genuine Kress chains or those against the weight of the machine. (See Fig. G) recommended for Guide Bar. -
Page 15: Operation
If there around saw handles. (See Fig. N) is no oil pattern, despite a full oil reservoir, contact Kress (4) Make sure your footing is firm. Keep feet-shoulder customer service agent or Kress approved service agent. -
Page 16: Maintenance And Storage Of Chainsaw
injury or death. to avoid possible bouncing or skating (sideways movement) of saw. When sawing logs supported on both ends, start the (7) Guide the saw using light pressure and do not put cut from above(Y) about 1/3 of the diameter into the excessive force on the saw, letting the saw do its log (overbuck) and then finish the cut (Z) from below, in work. -
Page 17: Environmental Protection
To clean the Bar rails: when lubricating the guide bar sprocket. 1. Remove chain cover and bar and chain. (see section 1. Clean the bar and sprocket ASSEMBLY) 2. Using a grease gun, insert the tip of the gun into the 2. -
Page 18: Declaration Of Conformity
DECLARATION OF Chainsaw Over heating Place the operates Applying too machine in a CONFORMITY intermittently much pressure cool, ventilated while cutting. place to cool it Loose connection. down. Positec Germany GmbH Internal wiring Applying Postfach 32 02 16, 50796 Cologne, Germany defective. - Page 19 DECLARATION OF CONFORMITY Positec (UK & Ireland) Ltd, PO Box 6242, Newbury, RG14 9LT, UK On behalf of Positec declare that the product Description Battery-powered chainsaw Type KG367E KG367E.X (3 - designation of machinery, representative of Chainsaw) Function Cutting wood Complies with the following regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016...
- Page 20 Copyright © 2023 Positec. All Rights Reserved. AR01562603...
Need help?
Do you have a question about the KG367E Series and is the answer not in the manual?
Questions and answers