Page 2
Para prevenir cualquier mal funcionamiento y evitar daños, por favor, lea detalladamente este manual de instrucciones antes de conectar y operar este equipo. If you have any questions about this product, you may call; Sony Customer Information Services Center 1-800-222-7669 or http://www.sony.com/ Declaration of Conformity Trade Name:...
If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards. For the customers in the UK If you use the monitor in the UK, be sure to use the appropriate UK power cord. Example of plug types...
(pages 8, 17, 22) This switch turns the monitor on when the 1 (power) indicator lights up in red. To turn the monitor off, press this switch again. If the 1 (power) indicator does not light up, press the MAIN POWER switch (7).
The security lock hole should be used with the Kensington Micro Saver Security System. Micro Saver Security System is a trademark of Kensigton. Setup Before using your monitor, check that the following items are included in your carton: • LCD display • Power cord •...
Connect a computer equipped with an HD15 output connector (analog RGB) Using the supplied HD15-HD15 video signal cable (analog RGB), connect the computer to the monitor’s HD 15 input connector (analog RGB). Connect the computer according to the following illustrations.
Setup 4: Turn on the monitor and 1 Press the MAIN POWER switch located on the right side of the monitor in the direction of the [, if it is not already pressed. Make sure the 1 (power) indicator is lit in red.
The vertical frequency is set to 60 Hz. Since flickers are unobtrusive on the monitor, you can use it as it is. You do not need to set the vertical frequency to any particular high value.
Selecting the input signal (INPUT button) Press the INPUT button. The input signal change each time you press this button. INPUT On-screen message Input signal configuration (Appears about 5 seconds on the upper left corner.) INPUT1 : HD15 HD15 input connector (analog RGB) for INPUT1 INPUT2 : HD15 HD15 input connector...
Customizing Your Monitor Before making adjustments Connect the monitor and the computer, and turn them on. For the best results, wait for at least 30 minutes before making adjustments. You can make numerous adjustments to your monitor using the on-screen menu.
When you select “USER,” the screen brightness turns to the level you adjusted with the ECO button on the front of the monitor. For more information, see “Reducing the power consumption (ECO mode)” on page 17. x Adjusting the BACKLIGHT If the screen is too bright, adjust the backlight to make the screen easier to see.
When receiving digital RGB signals from the DVI-D input connector, adjustment is unnecessary. x Automatic picture quality adjustment function When the monitor receives an input signal, it automatically adjusts the picture’s position and sharpness (phase/pitch), and ensures that a clear picture appears on the screen (page 18). Note While the automatic picture quality adjustment function is activated, only the 1 (power) switch will operate.
9 Press the m/M buttons to select “PITCH” and press the OK button. The “PITCH” adjustment menu appears on the screen. 10 Press the m/M buttons until the vertical stripes disappear. Adjust so that the vertical stripes disappear. 11 Click [END] on the screen to turn off the test pattern. x Adjust the picture’s position manually (H CENTER /V CENTER) If the picture is not in the center of the screen, adjust the picture’s...
3 Press the m/M buttons to select the desired mode and press the OK button. ZOOM menu The monitor is set to display the picture on the screen in full, irrespective of the picture’s mode or resolution in the default setting (FULL2).
** The maximum power consumption is 2.0 W in 100-120 V AC areas. Reducing the power consumption (ECO mode) If you press the ECO button on the front of the monitor repeatedly, you can select the screen brightness. (power) indicator...
This adjustment data is automatically stored in memory so that next time, the monitor will function in the same way as when the monitor receives the signals that match one of the factory preset modes.
GO TO POWER SAVE The monitor will enter the power saving mode after about 5 seconds from the time the message is displayed. If “CABLE DISCONNECTED” appears on the screen This indicates that the video signal cable has been disconnected from the currently selected connector.
If a problem occurs as a result of a connected computer or other equipment, refer to the connected computer/equipment’s instruction manual. Use the self-diagnosis function (page 22) if the following recommendations do not resolve the problem. For further information and troubleshooting assistance, please visit Sony support website at: Symptom...
Page 21
• Depending on the graphics board setting, the resolution displayed on the menu screen may screen is incorrect. After turning off the main power, • When the main power is on but the 1 (power) switch is not pressed, or when the monitor the 1 (power) indicator stays bright for a while.
Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the model name and specifications of your computer and graphics board.
TCO’99 Eco-document (for the black model) x Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Page 25
TCO’03 Eco-document (for the gray model) x Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.