Operating The Remote Control - Trane ProSpace PTEG0701GAA Installation, Operation And Maintenance Manual

R R e e s s t t o o r r e e F F a a c c t t o o r r y y S S e e t t t t i i n n g g s s
When pressing the Low button and p for 3 seconds, the
digital display shows 00 for 3 seconds in standby and
OFF status. This indicates that the factory settings have
been restored. The configuration information defaults
to display:
• Fahrenheit.
• Heating compensation temperature of 0.
• Cooling compensation of 0.
• Set temperature.
The T-value is 0, the Fan Speed is set to High, and the
set temperature is 71°F (22°C).

Operating the Remote Control

The optional ProSpace remote control has many of the
features that are accessible through the ProSpace front
panel. Ensure that there are no obstructions between
the receiver and the remote controller.
I I m m p p o o r r t t a a n n t t : : Do not drop or throw the remote control.
Do not spill any liquids in the remote
control. Do not put the remote control
directly into the sunlight or near hot
surfaces.
AUTO
COOL
DRY
FAN
HEAT
ON / OFF
FAN
SLEEP
• O O N N / / O O F F F F ; press to turn O O N N the unit and press again
to turn O O F F F F the unit. When turning ON / OFF the
unit, the T T i i m m e e r r and S S l l e e e e p p functions are cancelled,
but the pre-setting time is retained.
PTAC-SVX004A-EN
ON OFF
SWING
F OPER SLEEP
C LOCK
AUTO
H
SPEED
MODE
SWING
TIMER
• M M O O D D E E ; press to cycle through the mode selections
in the following order: Cool to Dry to Fan to Heat. In
Heat mode, the initial value is 82°F (28°C) and in
other modes, the initial value is 77°F (25°C).
N N o o t t e e : : Heat Mode is only for cooling/heating units. If
in Cooling Mode, there is no action taken
when the unit receives a call for heating.
B B l l o o w w - - o o v v e e r r h h e e a a t t : : when the unit is running in
Heat Mode or Auto Heat Mode, the
compressor and indoor fan running, to turn
the unit off, the compressor, outdoor fan will
stop running. The upper and lower guide
boards rotate to a horizontal position, the
indoor fan run at LOW FAN speed, and the 10
seconds later, the unit turns OFF.
• F F A A N N ; press to cycle through the fan speed selection
in the following order: AUTO to FAN 1 to FAN 2.
The speeds are represented on the remote as
vertical bars increasing in size for each speed.
When initializing the fan, the AUTO setting is
default.
N N o o t t e e : : Only LOW Fan Mode can be selected in DRY
mode. Pressing this key can not adjust the
fan speed, but can send message to the unit.
• S S L L E E E E P P ; Press to select SLEEP ON/OFF. When
powering the unit, the SLEEP OFF setting is default.
After setup is complete, the signal for SLEEP Mode
displays on the unit. While in SLEEP Mode, the
TIMER setting can be adjusted. SLEEP Mode is not
available in FAN and AUTO Modes. Once the unit is
turned OFF, the SLEEP Mode is cancelled.
• S S W W I I N N G G ; not used.
• T T I I M M E E R R ; in SWITCH OFF state, press this key to set
the time for AUTO SWITCH ON state. The range of
setting is between O.5 hours to 24 hours. The
characters T-ON and H flash for 5 seconds and
within this 5–second flash, press this key once to
complete the setting and send the message to the
unit. If this setting is valid, the set time displays for
2 seconds before displaying the temperature
message. During the 5–second flash, press + + key to
increase the time value and - - to decrease the value.
The values increase/decrease in increments of 0.5
hours with each press of the key. Pressing this key
in rapid successions to increase/decrease the
values will advance the increments quickly. The
remote controller can increase the set time by 0.5
hours every 0.25 seconds. After energizing the unit,
the default is NO TIMER setting and the T-ON or H
characters do not display. When the temperature
display becomes constant, press this key again to
display the remaining set time. The time values, T-
ON and H, display constantly for 2 seconds. After 2
seconds, the preset temperature displays. Within
these 2 seconds, press this key again to CANCEL
the AUTO SWITCH ON and send the message.
Pressing this key in SWITCH ON state allows the
time to be set to AUTO SWITCH OFF. Press ON/OFF
O O p p e e r r a a t t i i o o n n
23