Related Manuals for Hamplus AS-603HR
Summary of Contents for Hamplus AS-603HR
- Page 1 AS-603HR AS-61HR / RC-603HR / RPS-1 Set 6x3 Automatic Wireless Antenna Switch with Rotator Controller Commands over RF Cable Operation from 1.8 MHz to 54 MHz Operation Manual V. 1.1 http://www.hamplus.com - 1 - AS-603HR Operation Manual...
- Page 2 AS-61RL / RC-603RL / RPS-1 Set 6x3 Automatic Wireless Antenna Switch with Rotor Controller The AS-603HR / RPS-1 set is an automatic antenna switch for three Radios, six Antennas and control for two Rotors. There are three independent boxes, the AS-61RL...
- Page 3 RC-603RL with a cable, such as Hamplus ERC-6, IRC-6, KRC-6, YRC-6, FRC-6 or YRC-61, and the radio set to the correct baud rate (19,200 baud CI-V or 4800 baud CAT and COM) and set up as described in the previous section.
- Page 4 RC-603RL automatically change to the correct antenna. Correct any wrong Ant # on any band by manual selection. - 4 - AS-603HR Operation Manual...
- Page 5 Rotor clockwise (cw) in one complete revolution (360 degrees) using the Ant6 (cw) button and Ant4 (ccw) button until it reaches exactly the point where the Rotor started the turn. This is the end point of the Rotor stroke. - 5 - AS-603HR Operation Manual...
- Page 6 Antenna. 3- Choice of Rotor for the antenna: The AS-603HR can control up to two Rotors. This procedure is for associating an antenna to a Rotor. So, when you select the antenna the controller will be connected to the Rotor of this antenna, the LED indicator of the Rotor in use will be illuminated and the Display will indicate the position of the antenna.
- Page 7 5- Rotor stroke limit: In some installations, such as on the side of a tower, the antenna cannot rotate 360 degrees because it encounters obstacles. For these cases, the AS-603HR Rotor controller has the Stroke Limit function. Counterclockwise limit (CCW) a- First step- Position the antenna at the limit of the counterclockwise (CCW) direction.
- Page 8 2- Radio selection buttons 3- Azimuth indicator display 4- Power On LED indicator 5- Split Antenna LED indicator 6- Send indicator LED 7- Rotor 1 indicator LED 8- Encoder button 9- Rotor 2 indicator LED - 8 - AS-603HR Operation Manual...
- Page 9 6- RF from Radio 2 14- RF from Radio 3 7- RF Out to Amp. In 15- RF In from Linear Amp. Out 8- RF + DC + Com, Out to AS-61RL 16- GND - 9 - AS-603HR Operation Manual...
- Page 10 - 10 - AS-603HR Operation Manual...
- Page 11 Diagram of blocks and connections of the antenna switch AS-603HR without the rotator power supply module, mounted in two cabinets Cabinet 1 contains the RC-603RL controller Cabinet 2 contains the AS-61RL antenna switch - 11 - AS-603HR Operation Manual...
- Page 12 Diagram of the blocks and connections of the antenna switch AS-603HR with the rotator power supply module, mounted in three cabinets Cabinet 1 contains the RC-603RL controller Cabinet 2 contains the AS-61RL antenna switch Cabinet 3 contains the RPS-1 rotor power supply...
- Page 13 Diagram of blocks and connections of the antenna switch AS-603HR with the rotor power supply module, mounted in two cabinets Cabinet 1 contains the RC-603RL controller Cabinet 2 contains the antenna switch and the rotator power supply AS-61RLP - 13 -...
- Page 14 - 14 - AS-603HR Operation Manual...
- Page 15 - 15 - AS-603HR Operation Manual...
- Page 16 - 16 - AS-603HR Operation Manual...
- Page 17 - 17 - AS-603HR Operation Manual...
- Page 18 - 18 - AS-603HR Operation Manual...
- Page 19 - 19 - AS-603HR Operation Manual...
- Page 20 - 20 - AS-603HR Operation Manual...
- Page 21 - 21 - AS-603HR Operation Manual...
- Page 22 - 22 - AS-603HR Operation Manual...
- Page 23 ----------O---------- - 23 - AS-603HR Operation Manual...
Need help?
Do you have a question about the AS-603HR and is the answer not in the manual?
Questions and answers