Taurus GEYSER ECO EASY 2800 Manual page 7

Downloaded by: pd-oliana on 29-08-2022 11:31 CEST
- Do not use temperatures higher than those
indicated on the garments to be ironed.
● Temperature for synthetic fi bres (Polyester,
Nylon...).
●● Temperature for silk, wool.
●●● Temperature for cotton.
Max Temperature for linen.
- If garment has various kinds of fi bres, select the
temperature for the fi bre that requires the lowest
temperature. (For example, select the tempera-
ture for polyester for a fabric made out of 60%
polyester and 40% cotton).
- Wait until the pilot light (F) has gone out, indica-
ting that the appliance has reached an adequate
temperature.
- During use the pilot light (F) will automatically
fl ash on and off, indicating that the heating
elements are operating in order to maintain the
desired temperature.
DRY IRONING:
- The appliance has a steam fl ow regulator
which, when set to 1, allows dry ironing (without
steam).
STEAM IRONING:
- It is possible to iron with steam whenever the
tank has water and the adequate temperature
is selected.
STEAM FLOW CONTROL:
- The appliance has a (C) control knob for adjus-
ting the steam fl ow.
SPRAY:
- The spray can be used in both steam and dry
ironing.
- Press the spray button ( A ) to use this opera-
tion.
- The spray button has to be pressed repeatedly
to release the fi rst spray.
STEAM BLAST:
- This function provides extra steam for removing
creases.
- Press the steam blast button ( B ). Wait a few
seconds until the steam penetrates the fi bres of
the garment before pushing the button again.
For optimum steam quality, do not apply more
than three successive blasts.
- The spray button has to be pressed repeatedly
to release the fi rst spray.
Manual Geysers Eco.indb 7 Manual Geysers Eco.indb 7
VERTICAL IRONING:
- It is possible to iron hanging curtains, items
of clothing on their own hanger, etc. To do so,
follow these instructions:
- Select the iron's maximum temperature by tur-
ning the iron's temperature regulator clockwise.
(Fig 2)
- Iron from top to bottom while pressing the steam
control ( B ). Important: for cotton and linen, it is
recommended to put the base of the iron in con-
tact with the material. For other more delicate
fabrics, it is recommended to keep the base of
the iron a few centimetres away.
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Select the minimum position (MIN) using the
thermostat control.
- Unplug the appliance from the mains.
- Remove the water from the water tank.
- Clean the appliance.
CLEANING
- Unplug the appliance from the mains and let it
cool down before performing any cleaning task.
- Clean the appliance using a damp cloth with a
few drops of detergent and then dry it.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
- Do not immerse the appliance in water or any
other liquid, or place it under a running tap.
SELF-CLEANING FUNCTION:
- It is important to self-clean the appliance at least
once a month to remove calcium and any other
built-up minerals inside the iron.
- Fill the water tank to its maximum level, as indi-
cated in the "fi lling with water" section.
- Place the iron in an upright position, plug in to
the mains and select maximum temperature.
- Leave the appliance to heat up until the pilot
light indicates that it has reached its consigned
temperature.
- Unplug the appliance and place it in the sink.
- Press and hold the self-clean button.
- Let the water fl ow out through the steam vents
in the base, while lightly shaking the appliance.
- Release the button after a minute or when the
tank becomes empty.
- Leave the iron in the upright position until it has
cooled.
13/07/2022 16:37:43 13/07/2022 16:37:43