Summary of Contents for Advantech LEO-S552-THG0
- Page 1 Temperature / Humidity Sensor ® Featuring LoRaWAN LEO-S552-THG0 / LEO-S552-THC0 User Guide...
- Page 2 In order to protect the security of the device, please change device password when first c onfiguration. The default password is 123456. ❖ The device is not intended to be used as a reference sensor, and Advantech will not should responsibility for any damage which may result from inaccurate readings. ❖...
-
Page 3: Table Of Contents
3.5.1 Calibration Settings .................... 12 3.5.2 Threshold Settings ....................12 3.5.3 Alarm Settings ...................... 12 3.5.4 Data Retransmission ..................15 3.5.5 Advantech D2D Settings..................16 3.6 Maintenance ........................17 3.6.1 Upgrade ......................... 17 3.6.2 Backup ........................18 3.6.3 Reset to Factory Default ..................19 4. -
Page 4: Product Introduction
Sensor data are transmitted in real-time using standard LoRaWAN protocol. LoRaWAN enables encrypted radio transmissions over long distance while consuming very little power.The user can obtain sensor data and view the trend of data change through Advantech IoT Cloud or through the user's own Network Server. 1.2 Features ⚫... -
Page 5: Hardware Overview
If any of the above items is missing or damaged, please contact your sales representative. 2.2 Hardware Overview Front View: ① NFC Area Top View: ② Vent 2.3 Dimensions(mm) www.advantech.com... -
Page 6: Power Button
Light Off: Device is off. 3. Operation Guide 3.1 NFC Configuration LEO-S552-THG0 can be monitored and configured via NFC. Please refer the following steps to complete configuration. 1. Download and install “Advantech ToolBox” App from Advantech website. 2. Enable NFC on the smartphone and launch Advantech ToolBox. -
Page 7: Lorawan Settings
3) LEO-S552-THG0 can also be configured by dedicated NFC reader provided by Advantech or you can configure it via TTL interface inside the device. 3.2 LoRaWAN Settings ® LoRaWAN settings is used for configuring the transmission parameters in LoRaWAN network. - Page 8 LoRaWAN Version V1.0.2, V1.0.3, V1.1 are available. Work Mode It’s fixed as Class A. RX2 Data Rate RX2 data rate to receive downlinks or send D2D commands. RX2 Frequency RX2 frequency to receive downlinks or send D2D commands. Unit: Hz www.advantech.com...
- Page 9 Examples: 1, 40: Enabling Channel 1 and Channel 40 1-40: Enabling Channel 1 to Channel 40 1-40, 60: Enabling Channel 1 to Channel 40 and Channel 60 www.advantech.com...
-
Page 10: Time Synchronization
1) This function is only applicable to network server using LoRaWAN 1.0.3 or 1.1 version. 2) Network server will sync the time which time zone is UTC+0 by default. It's suggested to s ync the time via ToolBox App to change the time zone. www.advantech.com... -
Page 11: Basic Settings & Interface Settings
2) Please modify the threshold settings if the unit is changed. Change the password for ToolBox App or software to read/write this Change Password device. For LEO-S552-THG0-DI, go to Device > Settings > Interface Settings to modify configurations. Parameters Description Change the interface type of GPIO interface. -
Page 12: Advanced Settings
Go to Device > Setting > Threshold Settings to enable the threshold settings and input the threshold. LEO-S552-THG0 will upload the current data once instantly when the temperature threshold is triggered. Note that when you change the temperature unit, please re-configured the threshold. - Page 13 3.5.4 Data Storage LEO-S552-THG0 sensor supports storing more than 2000 data records locally and exports data via ToolBox App. The device will record the data according to reporting interval and even joining network. 1. Go to Device > Setting > General Settings to enable data storage feature.
- Page 14 3. Click Data Cleaning to clear all stored data inside the device. www.advantech.com...
-
Page 15: Data Retransmission
3.5.4 Data Retransmission LEO-S552-THG0 sensor supports data retransmission to ensure network server can get all data even if network is down for some times. There are two ways to get the lost data: ⚫ Network server sends downlink commands to to enquire the historical data for specifying time range, see section ⚫... -
Page 16: Advantech D2D Settings
2. Go to Device > Setting > D2D Settings to enable Advantech D2D feature. 3. Define an unique D2D key which is the same as Advantech D2D agent devices. (Default D2D key: 5572404C696E6B4C6F52613230313823) 4. Enable one of status mode and configure 2-byte hexadecimal Advantech D2D command. -
Page 17: Maintenance
1) If you enable LoRa Uplink, a LoRaWAN uplink packet that contains the sensor status or temperature threshold alarm will be sent to gateway after the Advantech D2D control ® command packet. Otherwise, sensor status or threshold alarm will not send to LoRaWAN gateway. -
Page 18: Backup
3.6.2 Backup LEO-S552-THG0 devices support configuration backup for easy and quick device ® configuration in bulk. Backup is allowed only for devices with the same model and LoRaWAN frequency band. 1. Go to Template page on the App and save current settings as a template. You can also edit the template file. -
Page 19: Reset To Factory Default
NFC area to device to complete reset. 4. Installation 1. Attach LEO-S552-THG0 to the wall and mark the two holes on the wall. The connecting line of two holes must be a horizontal line. 2. Drill the holes according to the marks and screw the wall plugs into the wall. -
Page 20: Device Payload
09 01 00 ff 0a 01 02 ff 0f 00 Channel Type Value Channel Type Value (Hardware 0100 (V1.0) (Software 0102(V1.2) version) version) Channel Type Value (Device Type) (Class A) 5.2 Sensor Data LEO-S552-THG0 sensors report sensor data according to reporting interval (10min by default). www.advantech.com... -
Page 21: Downlink Commands
10 01 => 01 10 = 272 64 => 100% (Battery) (Temperature) Temp=272*0.1=27.2°C 5.3 Downlink Commands LEO-S552-THG0 sensors support downlink commands to configure the device. The application port is 85 by default. Channe Type Description 03 (Set Reporting Interval) 2 Bytes, unit: s... - Page 22 Value 10 (Reboot) ff (Reserved) 3. Set a temperature threshold as below 15°C or above 30°C. ff 06 cc96002c0100000000 Channel Type Value CTRL:cc =>11001100 06 (Set Threshold 100 = below or above Alarm) Min:96 00=> 00 96 = 15°C www.advantech.com...
-
Page 23: Historical Data Enquiry
) D2D Command: 1001=>0110 5.4 Historical Data Enquiry LEO-S552-THG0 sensor supports sending downlink commands to enquire historical data for specified time point or time range. Before that, ensure the device time is correct and data storage feature was enabled to store the data. - Page 24 20ce 0d755b63 0f01 6a 02 06000000 00 Channel Type Time Stamp Value Temperature: 0f01=>010f=27.1°C Humidity: 6a=>106=53% 0d755b63 => ce (Historical Interface Type: 02=Counter; 2022/10/28 Data) (01=Digital) 14:22:05 Counter: 06 00 00 00=> 00 00 00 06 =6 Digital: 00=> low -END- www.advantech.com...