Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Advantech LEO-S572-TPG0
Summary of Contents for Advantech LEO-S572-TPG0
- Page 1 Temperature Probe Sensor ® Featuring LoRaWAN LEO-S572-TPG0 / LEO-S572-TPC0 User Guide...
- Page 2 In order to protect the security of the device, please change device password when first c onfiguration. The default password is 123456. ❖ The device is not intended to be used as a reference sensor, and Advantech will not should responsibility for any damage which may result from inaccurate readings. ❖...
- Page 3 4.4 Advanced Settings ......................13 4.4.1 Threshold Settings ....................13 4.5 Maintenance ......................... 13 4.5.1 Upgrade ........................13 4.5.2 Backup ........................14 4.5.3 Reset to Factory Default ..................15 5. Installation ............................16 6. Device Payload ..........................17 6.1 Payload Definition ......................17 www.advantech.com...
- Page 4 Sensor data are transmitted in real-time using standard LoRaWAN protocol. LoRaWAN enables encrypted radio transmissions over long distance while consuming very little power.The user can obtain sensor data and view the trend of data change through Advantech IoT Cloud or through the user's own Network Server. 1.2 Features ⚫...
- Page 5 If any of the above items is missing or damaged, please contact your sales representative. 2.2 Hardware Overview LEO-S572-TPG0 sensors is made up of a LoRa transceiver and a sensor. Among them, ultrasonic sensors and gas sensors are combined with LoRa transceiver. Front View of LEO-S572-TPG0: ①LoRa Antenna (Internal)
- Page 6 Red/PT1 Red/PT2 3. Device Assembly For parts of models, you need to connect sensor to the LEO-S572-TPG0 transceiver to make the whole device work. 1. Take off the mounting bracket on the transceiver, remove the screws, rubber seal and cover on the bottom of the device.
- Page 7 3. Put the motherboard back and restore everything to its due position. When restoring the cover, ensure the arrow faces the front of the transceiver. Note: Rubber seal and rubber screw caps should be installed accordingly, or the water will come into the device. www.advantech.com...
- Page 8 1) Ensure the location of smartphone NFC area and it’s recommended to take off phone case. 2) If the smartphone fails to read/write configurations via NFC, keep the phone away and back to try again. 3) LEO-S572-TPG0 can also be configured by dedicated NFC reader, which can be purchased from Advantech. www.advantech.com...
- Page 9 4.1.2 USB Configuration 1. Download ToolBox software from www.Advantech-iot.com. 2. Release the enclosure of the LEO-S572-TPG0 transceiver, then connect the device to a computer via Type-C port. 3. Open the ToolBox and select type as “General”, then click password to log in ToolBox.
- Page 10 RX2 Frequency RX2 frequency to receive downlinks. Unit: Hz Spread Factor If ADR is disabled, the device will send data via this spread factor. Confirmed Mode If the device does not receive ACK packet from network server, it will resend www.advantech.com...
- Page 11 Examples: 1, 40: Enabling Channel 1 and Channel 40 1-40: Enabling Channel 1 to Channel 40 1-40, 60: Enabling Channel 1 to Channel 40 and Channel 60 All: Enabling all channels www.advantech.com 11 1 1...
- Page 12 Description Reporting interval of transmitting data to network server.Default: 10 mins, Reporting Interval Range: 1-1080 mins. For LEO-S572-TPG0 sensor, change the temperature unit displayed on the ToolBox. Temperature Unit Note: 1) The temperature unit in the reporting package is fixed as °C.
- Page 13 4.4.1 Threshold Settings Go to “Device Settings->Basic” of ToolBox software or “Device->Setting->Threshold Settings” of ToolBox App to enable the threshold settings and input the threshold. LEO-S572-TPG0 will upload the current data instantly after the threshold is triggered. 4.5 Maintenance 4.5.1 Upgrade ToolBox Software: 1.
- Page 14 4.5.2 Backup LEO-S572-TPG0 devices support configuration backup for easy and quick device configuration in bulk. Backup is allowed only for devices with the same model and LoRa frequency band. 1. Go to “Template” page on the App and save current settings as a template. You can also edit the template file.
- Page 15 Hold on power button (internal) for more than 10s. Go to “Maintenance->Backup and Reset” to click “Reset”. Via ToolBox Software: Go to “Device->Maintenance” to click “Reset”, then attach smart phone Via ToolBox App: with NFC area to device to complete reset. www.advantech.com...
- Page 16 5. Installation LEO-S572-TPG0 transceiver support wall, pole and DIN rail mounting. Before installation, ensure the mounting bracket has fixed to the device via screws. Wall Mounting: 1. Drill 2 holes on the wall according to the mounting bracket, then fix the wall plugs into the wall.
- Page 17 6.1 Payload Definition Channel Type Description 75(Battery Level) UINT8, Unit: % 67 (Temperature) INT16, Unit: °C Examples: LEO-S552-TPG0 01 75 64 03 67 19 01 Channel Type Value Channel Type Value 19 01 => 01 19 = 281 64 => 100% (Battery) (Temperature) Temp=281*0.1=28.1°C -END- www.advantech.com...
Need help?
Do you have a question about the LEO-S572-TPG0 and is the answer not in the manual?
Questions and answers