Radio Shack 1201682 - Radio Alarm Clock With Bluetooth Speaker Manual

Introduction

We hope you enjoy your Radio Alarm Clock with Bluetooth^® Speaker from RadioShack. This radio features a 1.2" blue LED display, dual alarm clock, built-in USB charging port, and auxiliary input jack. Bluetooth connectivity enables you to wirelessly stream music from your Bluetoothenabled device. Please read this user's guide before using your new radio alarm clock.

Package Contents

• Radio Alarm Clock
• AC Adapter
• User's Guide

Specifications

Specifications are subject to change and improvement without notice. Actual product may vary from the images found in this document.

Power Your Radio

Install Backup Batteries

Batteries provide backup power during power outages. Settings and data memory will be lost if both AC power and batteries are removed.

1. Open the battery cover.
2. Install two AAA batteries (not included) as indicated by the polarity symbols (+ and –) marked inside.
   
3. Replace the battery cover.

Battery Notes

• Replace the batteries when the LED display dims or the sound becomes weak or distorted.
• Dispose of batteries promptly and properly. Do not burn or bury them.
• Use only fresh batteries of the required size and type.
• Do not mix old and new batteries, different types of batteries (alkaline or rechargeable), or rechargeable batteries of different capacities.
• If you do not plan to use the radio for a long time, remove the batteries. Batteries can leak chemicals that can damage electronic parts.

Plug the AC Adapter

Connect the supplied AC adapter barrel plug into the DC IN jack on the back of the radio, and plug the adapter into a standard AC outlet. The LED displays the time.

USB Charging Port
Connect a portable device for charging using an USB charging cable (not included).

+ / –

• Volume control.
• Set the time.

FM

• Press and hold to turn the radio or Bluetooth mode on/off.
• Press to switch between radio and Bluetooth mode.

AL1 / AL2
Turn the alarm on /off or set the alarm.

/

• Tune radio stations.
• Previous/next track (Bluetooth only).

TIME
Enter time-setting mode.

/snooze_dimmer/

• Answer/reject a call or play/pause playback (Bluetooth only).
• Turn the alarm snooze on.
• Toggle LED display brightness to high or low (selection disabled in Bluetooth or snooze mode, or when the alarm sounds).

Listen to Your Radio

Listen to FM Radio

1. Press and hold FM for 2 seconds to turn on the radio. The red FM indicator lights.
2. Press or to tune a station, or press and hold or to scan available stations.
3. Press + or – to increase or decrease the volume.

Listen to a Bluetooth Device

1. Press FM to switch to Bluetooth mode. The blue Bluetooth indicator flashes.
2. Activate your device's Bluetooth function (refer to your device's user's guide).
3. When your device locates RS1201682, select it. When paired, the blue indicator lights steadily.
4. Turn on the audio source. You can control your radio through your device or with the radio's / , /snooze_dimmer/ , and + / – buttons.
   • If you receive a call, you can answer the call by pressing /snooze_dimmer/ and speaking into the microphone.
   • Press and hold /snooze_dimmer/ for 2 seconds to reject the call.
   • When your device receives an incoming call, the Bluetooth connection is suspended and playback will pause.

Note: If the connected device moves too far from the radio, you will lose the Bluetooth connection.

Device Not Pairing

Many Bluetooth-enabled devices, such as speakers, remember the most recently paired source (music, smartphone, etc.) and automatically reconnect when turned on. This is convenient, but can prevent you from connecting to a new source.
If you can't pair your radio, you may need to disconnect it from its previous source.

Disconnect Your Device

To disconnect the paired device, press and hold the radio's /snooze_dimmer/ seconds. The radio starts searching for another Bluetooth device.

Listen to an AUX Device

For an audio device without Bluetooth technology, use an ⅛ in. audio cable (not included) to connect it to the radio's AUX IN jack. AUX appears on the display.

Notes:

• Bluetooth or FM radio mode is automatically deactivated when AUX IN is connected.
• Use the controls on your connected device to control playback.

Set the Clock

In standby mode, the time is shown using a 12hour clock with green PM indicator.

1. Press and hold TIME for 2 seconds to enter time-setting mode. The hour digits flash.
2. Press + or – to set the hour.
3. Press TIME. The minute digits flash.
4. Press + or – to set the minute.
5. Press TIME to confirm and exit.

Set the Alarm

You can set one or two alarms.

1. Press and hold AL1 (or AL2) for 2 seconds to enter alarm-setting mode. The hour digits flash.
2. Press + or – to set the hour.
3. Press AL1 (or AL2). The minute digits flash.
4. Press + or – to set the minute.
5. Press AL1 (or AL2), then press + or – to set the alarm source: b (Beep) or F (Radio).
6. Press AL1 (or AL2) to confirm and exit. The amber AL indicator lights.
7. Press AL1 (or AL2) once to review the alarm time, press it again to turn the alarm on/off.

When the Alarm Sounds

• The respective Alarm 1 or Alarm 2 indicator flashes. The alarm will sound for 1 hour at the set time, and the volume increases gradually to the maximum level.
• When the alarm time expires, the alarm will sound again the next day at the same time.
• To temporarily pause (snooze) the alarm for 9 minutes, press /snooze_dimmer/. The alarm indicator continues flashing. You can repeat snooze up to 7 times from when the alarm first sounds.
• To stop the alarm, press the respective alarm button (AL1 or AL2)