Service And Support; Operation - Philips SRC2063WM User Manual

E
t
o
o a
t
o
:
o
4
Service and
support
4.1
Frequently asked
questions
ln
this chapter you
will find
answers
to the most
frequently asked
questions about
your
universal
remote controls.
SetUp
I
cannot enter setup mode.
Battery
level
too
low
or
battery lifetime came
to
an end.
.
Replace
the batteries. See
chapter 2.1.
After
repldcing
the
batteries,
test
if
the
remote control still operates
your
devices,
lf
it does not, you have
to
set uP
the remote
control
again.
For
this refer
to
chapter
2.2
The
brand code
for
my
deviceis missing in
the
'shortlist
of brands' in
the Quick Start Guide.
The'shortlist of brands'only mentions
the most
commonTV, DVD,
CBUSAI DVR andVCR
brands, .
.
You
will
flnd
a
complete brand list
on
Page
31-42 of this user manual.
.
Use'9999'
as
4-digit code in case
you cannot
{ind
your brand
rn
the complete brand
list.
Note that
using'9999' may result in
a
long
setup (up
to
1
5 minutes).
MyTV switches OFF in step
4 but does'not
switch
ON
again
in step
5.
'
TVs
of
some brands (e.g.
Panasonic) only
switch
ON
after a
long
press
on one
of
the
digit buttons.After a long
button press
in setup
mode
the remote control will start
trying
to
improve
the button (see
chapter 2.2.2) rnstead
of
switching
ON theTV
.
ln this
case,
switch
ON
thery
manually
or
use
the original
remote control for
this.
Continue
with
step
6.After
successfully
completing
setup,the remote control will
switch
ON theTV with
a
long
button
press
oh one of
the
digit buttons, just
as
your
'
original
remote
control,
After
setup,
not
all buttons
work al expected.
.
Try
improving
the button(s), See chapter
2.2.2.
How do
I
set
up
the
remote
control for combo
devices
(TV
/VCR,ry
/
DVD, DVD /'VCR, etc)?
Some
combo
deVices
require you
to
set up
two
different device selection buttons
to
control
both parts of
the combo
device,
For example,
if
you
have
aW /
DVD combo, you might
need
to
set
up
the remote control for
both TV
and
DVD
to
operate
yourTV
/
DVD
combo.
Operation
The remote
control
does
not
wake up
anymore.
Battery level
too
low
or
battery lifetime came
to
an end.
.
Replace
the
batteries, See
chapter
2.'1.
After
replacrng
the
batteries,
test
if
the
remote control still operates
your
devices,
lf
it
does not, you have
to
set uP
the remote
control
again.
For
this refer
to
chapter
2.2,
.
The device
I
want
to
operate
does
not
respond
at all
/
does
not
respond
to
all
of the button
commands.
.
Check if
the buttons you press are available
on
the
original
remote control of
the
device,
.
Try
improving buttons. See
chapter 2.2.2.
Wrong code seleded
during setup.
.
Set
up
the remote control
again
forthe
device.Always
test
if
the
device responds,
before
leaving
setup mode.
It may
be
that the
buttons
that you are
trying
to
use have a different naming
on
the
original
remote
control.
.
Try out
all buttons
to find the one(s) you
need.
13 EN