Metso Lokotrack ST2.8 Driving Instruction
  1. Manuals
  2. Brands
  3. Metso Manuals
  4. Industrial Equipment
  5. Lokotrack ST2.8
  6. Driving instruction
Metso Lokotrack ST2.8 Driving Instruction

Metso Lokotrack ST2.8 Driving Instruction

Hide thumbs
Table of Contents

Advertisement

Quick Links

Lokotrack ST2.8
Doc No. D100014842 Revision 0
Original instruction
DRIVING INSTRUCTIONS
For more information and
language versions, see:
metso.com/driving

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lokotrack ST2.8 and is the answer not in the manual?

Questions and answers

Related Manuals for Metso Lokotrack ST2.8

Summary of Contents for Metso Lokotrack ST2.8

  • Page 1 Lokotrack ST2.8 Doc No. D100014842 Revision 0 Original instruction DRIVING INSTRUCTIONS For more information and language versions, see: metso.com/driving...
  • Page 2 Metso's liability for any errors in the document is limited to the documentary correction of errors.

  • Page 3: Table Of Contents

    1.12.7    Charging the battery of radio control device............28 1.12.8    Jump starting the engine with another machine or vehicle........29 3 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
  • Page 4 1.12.17    Recovering from too high hydraulic oil temperature..........35 1.12.18    Checking if manual controls are active..............36 1.12.19    Checking if process in running................37 4 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 5: Driving Instructions

    1    Driving instructions 1    Driving instructions These driving instructions are valid for Lokotrack ST2.8. The purpose of these instructions is to enable safe moving of the machine during transportation. NOTE: Do not use the machine for screening or crushing solely based on these instructions. The actual instruction manual for the machine is delivered separately.

  • Page 6: Driving Directions

    • The driving surface is not icy or slippery. If needed, sprinkle sand on the surface. 1.2    Driving directions Callout Description Callout Description Forward Left Backward Right Figure 1. Lokotrack ST2.8 driving directions 6 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 7: Emergency Stop Locations

    (located on either the radio control box or the remote control box). Figure 2. Emergency stop button 7 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 8: Remote Stop Location

    On the left-hand side of the machine On the right-hand side of the machine On the left-hand side of the machine On the right-hand side of the machine Figure 3. Locations of the Lokotrack ST2.8 emergency stop buttons 1.4    Remote stop location DANGER GENERAL HAZARD Will cause death or serious injury.

  • Page 9: Drive Controls

    Only lift and hold the drive control device by its handles. Do not pull the drive control device from the cable. 9 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
  • Page 10 NOTE: Check that the connectors are clean and that there is no water in the plugs or connectors. NOTE: Make sure that the drive control device is stored properly to avoid damages, dirt, and water. 10 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 11: Radio Control Device (Optional)

    Grid lifting (UP) Remote stop (push and (optional) pull button) Grid lowering (DOWN) Crushing/screening, (optional) hydraulic operations, 11 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision: Metso Document ID: D100014842...

  • Page 12: Preparing For Driving

    2. Visually inspect that there are no loose parts, and everything is secured in place. 3. Check the inclinations, approach angle, and departure angle of the machine. 12 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
  • Page 13 4. Open the door of main control center. Figure 9. Main control panel location (on the right side of the machine) 13 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
  • Page 14 NOTE: You must start the engine before connecting the drive control device or radio control device. Otherwise, you must reconnect/reactivate the control device. 14 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 15: Starting The Engine

    2. Locate the main switch and turn it to ON position. Figure 11. Main switch 3. Locate the main control panel. 15 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
  • Page 16 Release the Engine start/stop button when the engine is running. Troubleshooting If the engine does not start, see Figure 14. Engine start/stop button 16 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision:...

  • Page 17: Connecting The Control Device

    • The drive control device cannot be used if the radio control mode is switched on. 4. On the main control panel, make sure that the radio control mode ON/OFF switch is in position 0 (OFF). 17 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 18: Connecting The Radio Control Device

    Driving Check the directions of drive control levers compared to the directions of the machine from directions 18 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision:...
  • Page 19 Driving speed range Engine speed Slow driving 850..1200 Normal driving 1200...max 19 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision: Metso Document ID: D100014842...

  • Page 20: Driving With Radio Control Device

    1. This step is only for machines with Constant Speed Engine (CSE): From the main control panel, make sure that the track speed selector switch is in the “Slow” (Turtle) position before driving the machine. 20 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
  • Page 21 NOTE: After driving with track drive continuously for 30 minutes: Stop and wait for 30 minutes, to allow the components to cool down before continuing the track drive. 21 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 22: Stopping The Engine

    NOTE: If the machine is to be shipped or stored, make sure that the main switch is left in OFF position. This is for preventing decrease in battery charge level. 22 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 23: Troubleshooting

    Lokotrack ST2.8 Driving Instructions Figure 23. Lokotrack ST2.8 main switch in OFF position 1.11    Troubleshooting 1.11.1    System display does not start Cause Battery is empty, the main switch is in OFF position, or battery clamps are not attached.

  • Page 24: Radio Control Device Is Not Working

    The machine cannot be driven to any direction. Checking if process in running Check if the process is running. See 24 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 25: Engine Is Not Running Properly Or It Suddenly Stopped

    Remote stop button is pressed down. Remedy Engine start is prevented. Handling the 'A17: Remote stop active' alarm 25 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision: Metso Document ID:...

  • Page 26: System Display Shows An Emergency Stop Alarm

    For the locations of emergency stop buttons, see Emergency stop locations 2. If an emergency stop button is pressed down, reactivate it by pulling the red knob. 26 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 27: Making Sure That Remote Stop Button Is Not Pressed Down

    1.12.5    Making sure that the battery clamps are attached 1. Locate the battery, and check if the battery clamps are attached properly. 27 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 28: Charging The Battery Of Lokotrack St Unit

    Lokotrack ST2.8 Driving Instructions Figure 27. Lokotrack ST2.8 battery location 2. If the battery clamps are loose, attach them. 1.12.6    Charging the battery of Lokotrack ST unit 1. If the batteries (24 V ) of the machine need to be charged, locate the battery and remove the + cable from the battery during charging to avoid damage to the electrical system.

  • Page 29: Jump Starting The Engine With Another Machine Or Vehicle

    1. Connect the jump cables to the portable jump starter while it is still in the off position. If the cables are permanently attached to the unit, you can ignore this step. 29 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 30: Checking The Fuel Level

    NOTE: Reading and understanding the alarm messages as well as the using the help information will help you to understand functions of the machine. 30 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...
  • Page 31 Driving Instructions NOTE: If there is a malfunction that is preventing the track driving, it must be fixed before proceeding. If necessary, contact Metso. In a problem situation, check if there are any active alarms. 1. From the main view, check if the alarm indicator (1) is red or grey.
  • Page 32 Active warning: (black message text), light-grey icon black-yellow icon Figure 33. Alarm view symbols and descriptions 32 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No: Revision: Metso Document ID:...

  • Page 33: Handling The 'A17: Remote Stop Active' Alarm

    Figure 34. Hydraulic oil level 2. Make sure that coolant level is between MIN and MAX markings. Add coolant, if necessary. 33 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 34: Checking The Hydraulic Oil Level And Possible Leaks

    4. Make sure that the inclination angle of the machine is not too large. See Preparing for driving Correcting too large inclination angle of the machine 34 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 35: Opening The Hydraulic Shut-Off Valve

    Check the hydraulic oil temperature by doing the following: 1. From the main view of the control panel display, tap Information views (3). 2. Tap ST information (1). 35 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...

  • Page 36: Checking If Manual Controls Are Active

    Wait for the status symbol to get grey color, and then you can activate the track driving again. 36 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type:...

  • Page 37: Checking If Process In Running

    1. Push the Process stop button from the main control panel to stop the screening process and to enable track driving. Figure 40. Process stop button 37 (38) © Copyright Metso 2023. All rights reserved. Project ID: Plant Code: Plant Unit Code: Document Type: Running No:...
  • Page 38 Metso PO Box 1220, FI-00101, Helsinki, Finland Tel +358 20 484 100 www.metso.com © Copyright Metso 2023. All rights reserved.

Table of Contents