Table of Contents
Advertisement
Quick Links
STORM
INSTRUCTIONS FOR
710W 230V
Reciprocating Saw
Stock No.83628
Part No.RS710SF
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper STORMFORCE RS710SF
Summary of Contents for Draper STORMFORCE RS710SF
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS CONTENTS PAGE CONTENT PAGE TITLE PAGE INTRODUCTION ....................2 REVISION HISTORY....................2 UNDERSTANDING THIS MANUAL ...............2 COPYRIGHT NOTICE....................2 CONTENTS CONTENTS ......................3 GUARANTEE GUARANTEE ......................4 INTRODUCTION SCOPE ........................5 SPECIFICATION ......................5 HANDLING & STORAGE ..................5 HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS ...............6 - 7 ADDITIONAL SAFETY INSTRUCTIONS ..............7 CONNECTION TO THE POWER SUPPLY..............7 TECHNICAL DESCRIPTION... -
Page 4: Guarantee 3.1 Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
INTRODUCTION 4.1 SCOPE This versatile tool is designed to cut wood, plastic and metal, including sheet materials, branches/logs and window surrounds. It is intended for domestic and light commercial use only. Any other application is considered misuse. 4.2 SPECIFICATION Stock no ...........................83628 Part no .......................... -
Page 6: Health & Safety Information
HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS General Power Tools Safety Warnings WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool”... -
Page 7: Additional Safety Instructions
HEALTH & SAFETY INFORMATION g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards. 4) Power Tool Use And Care a) Do not force the power tool. -
Page 8: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Adjustable foot. Rear hand grip. Quick release clamp. Approved moulded plug and 3m cable. Front hand grip. Lock-on button. Trigger switch. Rotating rear handle. Handle rotation switch. -
Page 9: Unpacking & Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the saw. -
Page 10: Setting The Reciprocating Saw
SETTING THE RECIPROCATING SAW Remove the plug from the socket before carrying FIG.1 out adjustment, servicing or maintenance. 8.1 BLADE INSTALLATION - FIGS. 1 - 2 Turn the blade clamp counter-clockwise. Insert the blade into the slot of blade clamp Release the blade clamp to lock the blade. -
Page 11: Basic Reciprocating Saw Operation
BASIC RECIPROCATING SAW OPERATION 9.1 SWITCH AND VARIABLE STROKE FIG.5 RATE CONTROL - FIG. 5 Your reciprocating saw is equipped with a trigger switch to turn the saw on and off, and to control the speed. To start the saw, press the trigger switch To stop the saw, release the trigger switch. -
Page 12: Plunge Cutting
BASIC RECIPROCATING SAW OPERATION 9.3 PLUNGE CUTTING - FIGS. 6 - 7 FIG.6 WARNING: Plunge cutting is only suitable when working softer materials such as wood or plaster board! However, this requires a degree of practice and is only possible with short saw blades. Place the tool via the pivoting footplate onto the work piece and switch on. -
Page 13: Optional Accessories
10. OPTIONAL ACCESSORIES 10.1 OPTIONAL ACCESSORIES Stock No. Part No. Description Quantity 02313 RSB/MP 150mm Multi purpose cutting blade 5 piece 02314 RSB/MP 200mm Multi purpose cutting blade 5 piece 02315 RSB/MP 250mm Multi purpose cutting blade 5 piece 02316 RSB/MP 300mm Multi purpose cutting blade 5 piece... -
Page 14: Maintenance
11. MAINTENANCE 11.1 MAINTENANCE & PARTS REPLACEMENT Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. For this reason avoid blocking the air inlets. -
Page 15: Troubleshooting
12. TROUBLESHOOTING WARNING: FOR YOUR OWN SAFETY ALWAYS TURN THE MAIN SWITCH OF THE MACHINE “OFF” AND REMOVE THE PLUG FROM THE POWER SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE OR TROUBLESHOOTING. PROBLEMS POSSIBLE CAUSES REMEDY Motor does not 1. Fuse 1. -
Page 16: Explanation Of Symbols
13. EXPLANATION OF SYMBOLS 13.1 EXPLANATION OF SYMBOLS Warning! Wear dust mask. Warning! Read the instruction manual Warning! Warning! Wear suitable eye/face Wear ear defenders. protection. WEEE Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish Class II construction (Double insulated). -
Page 17: Disposal
14. DISPOSAL 14.1 DISPOSAL - At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 18 NOTES...
- Page 19 NOTES...
- Page 20 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Help Line for details of an agent in your local area. YOUR DRAPER STOCKIST RDCH0816...
Need help?
Do you have a question about the STORMFORCE RS710SF and is the answer not in the manual?
Questions and answers
Cannot put the blade in
To insert the blade in a Draper STORMFORCE RS710SF reciprocating saw:
1. Turn the blade clamp counterclockwise.
2. Insert the blade into the slot of the blade clamp.
3. Release the blade clamp to lock the blade in place.
Warning: If changing the blade immediately after use, allow it to cool first to avoid burns.
This answer is automatically generated