Table of Contents
Advertisement
Available languages
Available languages
■
Powdered detergent:
A
Selector in position for powdered detergent
A. Detergent type selector
Chlorine bleach compartment
(Letter D in Dispenser Illustration)
Add no more than 2/3 cup (160 mL) liquid chlorine bleach to
this compartment. The bleach will be automatically diluted and
dispensed at the optimum time during the first rinse after the
wash cycle. This compartment cannot dilute powdered bleach.
■
Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
■
Do not fill beyond the "MAX" level.
NOTE: Overfilling could cause garment damage.
■
At the end of the cycle, a small amount of water may be left in
the dispenser. This is normal.
Fabric softener compartment
(Letter E in Dispenser Illustration)
Pour measured liquid fabric softener into the fabric softener
dispenser, if desired.
IMPORTANT: Dilute all fabric softener with water for a total of
1/4 cup (60 mL).
■
Do not overfill. The dispenser holds 1/4 cup (60 mL).
■
Do not spill or drip any fabric softener onto the clothes.
NOTES:
■
Use only liquid fabric softener in this dispenser.
■
Do not use fabric softener dispensing balls in this washer.
Dispensing balls will not operate correctly with this washer.
Pausing or Restarting
1. To pause the washer at any time, press PAUSE/CANCEL.
2. To continue the cycle, press START (for approximately
1 second).
Changing Cycles, Options, and Modifiers
Not all Options and Modifiers are available with all cycles.
Available modifiers will glow amber. If an Option or Modifier is
unavailable with a selected cycle, the light will not illuminate.
Cycles, Options, and Modifiers can be changed anytime before
START is selected.
Options and Modifiers can be changed anytime after START is
selected and before the start of the selected Option or Modifier.
To cancel a cycle and select a new cycle
1. Press PAUSE/CANCEL twice.
2. Press POWER.
3. Select desired cycle.
4. Select the desired Options or Modifiers such as Water Temp,
Spin Speed, and Soil Level.
5. Press START (for approximately 1 second) to restart the
washer at the beginning of the new cycle.
To cancel a cycle
1. Press PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can
be removed.
NOTE: If the water level or the temperature is too high, the washer
will drain automatically before the door unlocks.
To change Options or Modifiers after the cycle has started
1. Press PAUSE/CANCEL once.
2. Select the desired Options or Modifiers such as Water Temp,
Spin Speed, and Soil Level. Available selections will glow
amber.
3. Press START (for approximately 1 second) to continue the
cycle.
To drain the washer manually
1. Press PAUSE/CANCEL twice.
2. Press POWER.
3. Select DRAIN/SPIN.
4. Press START (for approximately 1 second) to begin the drain.
5. When the spin is complete, the door unlocks. Items can be
removed from the washer.
Status Lights
These lights show which portion of the cycle the washer is
operating. They also indicate when you can add an additional
item to the wash cycle and when the controls are locked.
Add a garment
This washer allows an 8-minute period in which other garments
may be added to the load. You can add items to the washer if the
status indicator shows Add a Garment.
To add items
1. Select PAUSE/CANCEL once. The washer door unlocks and
items can be added.
2. To continue the cycle, close the door and select Start (for
approximately 1 second).
3. To unlock the door after the Add a Garment period, press
PAUSE/CANCEL twice. This will cancel the Wash Cycle.
Done
The Done status light stays on for 60 minutes after the cycle is
complete, and then the washer shuts off.
Controls Lock/Unlock
The Controls Lock avoids unintended use of the washer. You can
also use the control lock feature to avoid unintended cycle or
option changes during a cycle. When Controls Lock is lit, all
buttons are disabled except for Pause/Cancel and Start. You can
lock the controls while the washer is operating.
13
Advertisement
Table of Contents
