Bosch B942 Installation Manual page 2

6 | Audible tones
The keypad has a built-in speaker that produces several distinct warning
tones. The keypad backlight illuminates when it emits an audible tone.
Tone Description
Fire alarm When an area is in fi re alarm, the keypad emits
a pulsed, high-pitched bell tone.
Gas alarm When a gas point activates, the keypad emits a
unique high pitched tone.
User alarm When a user alarm (such as panic and medical
alarms) occurs, the tone sounds for the
programmed amount of time.
Burglary alarm When an area is in alarm, the keypad emits a
steady, high pitched bell tone.
Entry delay The keypad emits an intermittent beep tone
during entry delay periods to remind the user
to disarm the area.
Exit delay The keypad emits an intermittent beep tone
during exit delay.
Invalid button When an invalid button, or sequence of
buzz buttons, is pressed, the keypad emits a fl at
buzz tone.
Keypress The keypad emits a muted beep tone as each
button is pressed to indicate that the entry
was accepted.
Trouble When a trouble event occurs, such as a service
alert, the keypad emits a two-tone warble until
you enter a programmed passcode with the
appropriate authority.
Watch point fault A single clean tweedle tone alerts the user
anytime a watch point is faulted.
Table 6.1: Keypad audible tones
7 | Supervision
The control panel supervises all keypads on the SDI2 bus.
If a keypad fails to respond to the control panel, the control panel
declares a Missing Keypad Trouble. When the control panel can
again communicate with the keypad, it restores the Missing Keypad
Trouble.
During a Missing Keypad Trouble, any connected keypad that
maintained contact with the control panel shows the Missing Keypad
Trouble as its idle text, and shows the missing keypad's address. The
communicating keypads also sound a trouble tone. Users can silence
the trouble tone. If no other troubles exist, the tone silences when
the missing keypad restores.
8 | Proximity reader
The proximity reader allows users to use a token or card in place
of a passcode to turn on or off the security system, if programmed
using RPS or a keypad. The proximity reader supports EM4102
(125 kHz) credentials. The Bosch ACA-ATR13-RFID tag and Bosch
ACD-ATR11ISO-RFID card are examples.
9 | Confi gure programmable keys functions
To enable the programmable keys functions use RPS to set the A,B,C
Key Response parameters (KEYPADS/Global Keypad Settings) as follows:
- To enable the Fire key, set A Key Response to Manual fi re alarm.
- To enable the Medical key, set B Key Response to Manual medical
alarm (with or without alarm bell).
- To enable the Panic key, set C Key Response to Manual panic alarm
(invisible or visible).
10 | Addresses, points, and output numbers
To determine the point numbers or output number for each keypad
address, multiply the address number by 10 for the base number, and
then use numbers 1 through 4 in the ones place for the point
numbers. Use 1 in the ones place for the output number.
Examples
For keypad address 01 the point numbers for the input devices are 11
through 14:
Terminal number 1 2 3 4
Input number 11 12 13 14
For output devices connected to the NO and C terminals the output
number is 11.
For keypad address 11 the point numbers for the input devices are 111
through 114:
Terminal number 1 2 3 4
Point number 111 112 113 114
For output devices connected to the NO and C terminals the output
number is 111.
11 | Firmware updates
Firmware updates require a MicroSD card (2 GB to 32 GB).
Updating the keypad fi rmware:
1. Go to the Bosch website (us.boschsecurity.com) and download
the fi rmware from the B942 product page.
2. Save the fi rmware to your MicroSD card.
3. Ensure the keypad is powered.
4. Slide the MicroSD card into the MicroSD card slot until it clicks
into place. Refer to Figure 11.1.
5. The keypad power indicator LED fl ashes during the update. The
keypad also shows Please wait while programming fl ash.
6. If the keypad shows the calibration screen, follow the on-screen
instructions to calibrate.
7. When the update completes, the keypad shows Firmware update
successful. Remove SD card to continue.
8. Remove the memory card from the device. To do so, press down
on the card and quickly remove pressure. The card clicks out of
place. Use your fi ngernail on the upper groove on the card to
slide it out.
9. The keypad shows the power up screen with the updated
revision number and then shows the Home screen.
R Y G B
1 COM 2 COM 3 COM 4 COM NO C
PWR A B COM
Figure 11.1: Inserting a MicroSD card
12 | Keypad cleaning
12 | Certifi cations
Use a soft cloth and non-abrasive cleaning solution to clean your keypad
(for example, microfi ber cloth and eyeglass cleaner). Spray the cleaner
onto the cloth. Do not spray cleaners directly onto the keypad.
13 | Certifi cations
Region Certifi cation
US UL 365 - Police Station Connected Burglar Alarm Units
and Systems
UL 609 - Local Burglar Alarm Units and Systems
UL 636 - Holdup Alarm Units and Systems
UL 985 - Household Fire Warning System Units
UL 1023 - Household Burglar-Alarm System Units
Region Certifi cation
US UL 1076 - Proprietary Burglar Alarm Units and Systems
UL 1610 - Central Station Burglar Alarm Units
CSFM - California Offi ce of The State Fire Marshal
FCC Part 15 Class B
ANSI/SIA CP-01-2010 - Control Panel Standard - Features
for False Alarm Reduction
CA Canada CAN/ULC S303 - Local Burglar Alarm Units and
Systems
CAN/ULC S304 - Signal Receiving Centre and Premise
Alarm Control Units
CAN/ULC S545 - Residential Fire Warning System Control
Units
ULC-ORD C1023 - Household Burglar Alarm System Units
ULC-ORD C1076 - Proprietary Burglar Alarm Units and
Systems
ICES-003 - Digital Apparatus
14 | Specifi cations
Dimensions 6.2 in x 4.7 in x 0.6 in
(158 mm x 120 mm x 16 mm)
Voltage (input) 12 VDC nominal
Current with prox 200 mA in standby mode
detection disabled 300 mA in alarm mode
Current with prox 300 mA in standby mode
detection enabled 400 mA in alarm mode
Operating temperature 0°C to +50°C (+32°F to +122°F)
Relative humidity 5% to 93% at +32°C (+90°F) non-
condensing
Terminal wire size 18 AWG to 22 AWG (1.02 mm to 0.65
mm)
SDI2 wiring with prox Maximum distance - wire size
detector disabled (unshielded wire only):
200 ft (61 m) - 22 AWG (0.65 mm)
520 ft (159 m) - 18 AWG (1.02 mm)
SDI2 wiring with prox Maximum distance - wire size (unshielded
detector enabled wire only):
150 ft (46 m) - 22 AWG (0.65 mm)
390 ft (119 m) - 18 AWG (1.02 mm)
Compatibility B9512G/B9512G-E
B8512G/B8512G-E
B5512/B5512E fi rmware v2.03 and higher
B4512/B4512E fi rmware v2.03 and higher
B3512/B3512E fi rmware v2.03 and higher
D9412GV4 fi rmware v2.03 and higher
D7412GV4 fi rmware v2.03 and higher
(Refer to the control panel installation
document for number of supported
devices.)
Copyright
This document is the intellectual property of Bosch Security Systems,
Inc. and is protected by copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are
likely to be registered trademarks and must be treated accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the
Bosch Security Systems, Inc. website at
http://www.boschsecurity.com/datecodes/.
Touch Screen Keypad
B942/B942W
en Installation Guide
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.com
© 2015 Bosch Security Systems, Inc. F.01U.294.527 | 05 | 2015.02