Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PCSS 10-1200
Summary of Contents for Trotec PCSS 10-1200
- Page 1 PCSS 10-1200 ORIGINAL INSTRUCTIONS PORTABLE CIRCULAR SAW...
-
Page 2: Table Of Contents
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. Notice This signal word indicates important information (e.g. material damage), but does not indicate hazards. Operating manual – portable circular saw PCSS 10-1200... -
Page 3: Safety
Damaged or entangled cords increase the risk of electric shock. • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. Operating manual – portable circular saw PCSS 10-1200... - Page 4 General Power Tool Safety Warnings – Service • Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Operating manual – portable circular saw PCSS 10-1200...
- Page 5 Additional safety warnings for portable circular saws other blind areas. The protruding blade may cut objects that can cause kickback. • Do not reach into the chip ejector with your hands. They could be injured by rotating parts. Operating manual – portable circular saw PCSS 10-1200...
- Page 6 We recommend using the power tool with original Trotec • Use suitable detectors to determine if utility lines are accessories. hidden in the work area or call the local utility company for assistance.
-
Page 7: Information About The Device
The device is equipped with a start lock preventing unintentional If necessary, use a pipe detector to check the wall you switch-on of the device. want to drill in or slit open. Operating manual – portable circular saw PCSS 10-1200... - Page 8 • 1 x Carbide saw blade 24 teeth (for wood and plastic) • 1 x Rip fence • 1 x Adapter for dust extraction • 1 x SW6 Allen wrench • 1 x Replacement blade wrench • 1 x Manual Operating manual – portable circular saw PCSS 10-1200...
-
Page 9: Transport And Storage
• The specified total vibration and noise emission values can also be used for preliminary load assessment. Operating manual – portable circular saw PCSS 10-1200... -
Page 10: Start-Up
Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. 3. Lock the locking lever (9) again. Operating manual – portable circular saw PCSS 10-1200... - Page 11 1. Release the locking lever for the cutting angle (2). 2. Set the desired cutting angle on the cutting angle scale (23). 3. Lock the locking lever (2) again. Operating manual – portable circular saw PCSS 10-1200...
- Page 12 3. Place the device on the front side of the motor housing. the clamping flange (17). 6. Then withdraw the replacement blade wrench (13). 7. Remove the clamping screw (18) together with the washer (24) as well as the clamping flange (17). Operating manual – portable circular saw PCSS 10-1200...
- Page 13 12. Please note that the lower guard (16) must be swung back using the retracting lever (20) in order to insert the saw blade. 14. Carefully swing the lower guard (16) back into its initial position with the retracting lever (20). Operating manual – portable circular saw PCSS 10-1200...
- Page 14 16. Place the clamping screw (18) together with the 19. Then withdraw the replacement blade wrench (13). washer (24) onto the clamping flange (17). 20. Check whether the saw blade is properly locked in place. Operating manual – portable circular saw PCSS 10-1200...
- Page 15 1. Loosen the wing screw (3) and insert the rip fence (15) into fence (15) and the arrow (27) on the base plate. the rip fence holder (4). The figure below shows a 4 cm setting by way of example: 45° 0° 3. Retighten the wing screw (3). Operating manual – portable circular saw PCSS 10-1200...
- Page 16 < 5 mm 5 mm max. Observe the following information: < 5 mm 5 mm max. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. Operating manual – portable circular saw PCSS 10-1200...
-
Page 17: Operation
Remove any oil before starting to saw to prevent oil residues from reaching the wood. • When sawing lightweight construction materials, observe the legal regulations and recommendations of the material manufacturers. Operating manual – portable circular saw PCSS 10-1200... - Page 18 11. After completing the sawing operation, let go of the on/off switch (7) to stop the device. 7. Press the on/off switch (7) and hold it during operation. ð The device operates with the previously selected settings. Operating manual – portable circular saw PCSS 10-1200...
-
Page 19: Available Accessories
Using insertion tools or accessories other than those specified in the operating manual may cause a risk of Notice injury. Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on. Operating manual – portable circular saw PCSS 10-1200... -
Page 20: Maintenance
• Non-coated saw blades can be protected against corrosion by applying a thin layer of acid-free oil. Remove any oil before starting to saw to prevent oil residues from reaching the wood. Operating manual – portable circular saw PCSS 10-1200... -
Page 21: Declaration Of Conformity
Declaration of conformity Operating manual – portable circular saw PCSS 10-1200... - Page 23 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...