Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PCSS 10-1400
Summary of Contents for Trotec PCSS 10-1400
- Page 1 PCSS 10-1400 OPERATING MANUAL PORTABLE CIRCULAR SAW...
-
Page 2: Table Of Contents
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. Notice This signal word indicates important information (e.g. material damage), but does not indicate hazards. Operating manual – portable circular saw PCSS 10-1400... -
Page 3: Safety
The use of a dust • Do not expose power tools to rain or wet conditions. extraction system may reduce dust-related hazards. Water entering a power tool will increase the risk of electric shock. Operating manual – portable circular saw PCSS 10-1400... - Page 4 If both hands are holding the saw, they cannot be cut by the blade. • Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece. Operating manual – portable circular saw PCSS 10-1400...
- Page 5 We recommend using the power tool with original Trotec • Lower guard may be retracted manually only for accessories. special cuts such as "plunge cuts" and "compound cuts".
- Page 6 Wear eye protection and a dust mask! Hold onto the mains plug while pulling the power cable Warning out of the mains socket. Do not process materials containing asbestos. Asbestos is considered carcinogenic. Operating manual – portable circular saw PCSS 10-1400...
-
Page 7: Information About The Device
2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains. Operating manual – portable circular saw PCSS 10-1400... - Page 8 • 1 x Rip fence • 1 x Adapter for dust extraction • 1 x SW6 Allen wrench • 2 x Battery (button cell type AG 13 / LR 44, 1.5 V) • 1 x Manual Operating manual – portable circular saw PCSS 10-1400...
-
Page 9: Transport And Storage
EN 62841 and can be used for a device comparison. The specified vibration emission value may also be used for a preliminary assessment of the exposure. Operating manual – portable circular saw PCSS 10-1400... -
Page 10: Start-Up
Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. 3. Lock the locking lever (10) again. Operating manual – portable circular saw PCSS 10-1400... - Page 11 1. Loosen the wing screw for the cutting angle (5). 2. Set the desired cutting angle on the cutting angle scale (28). 3. Retighten the wing screw (5). Operating manual – portable circular saw PCSS 10-1400...
- Page 12 7. Let go of the spindle lock (26). 8. Remove the clamping screw (19) together with the washer (29) as well as the clamping flange (18). 9. Remove any material residues from the device, in particular from the lower guard. Operating manual – portable circular saw PCSS 10-1400...
- Page 13 13. Please note that the lower guard (17) must be swung back using the retracting lever (21) in order to insert the saw blade. 15. Carefully swing the lower guard (17) back into its initial position with the retracting lever (21). Operating manual – portable circular saw PCSS 10-1400...
- Page 14 21. Place the Allen wrench (14) back into the holder. 22. Check whether the saw blade is properly locked in place. 17. Place the clamping screw (19) together with the washer (29) onto the clamping flange (18). Operating manual – portable circular saw PCSS 10-1400...
- Page 15 2. Open the battery compartment. 5. Close the battery compartment cover (23) and retighten the screw. 3. Remove any used batteries. Dispose of them according to the national regulations. Operating manual – portable circular saw PCSS 10-1400...
- Page 16 3 to 5 Hardwood and softwood (solid wood) for cross and longitudinal cuts Chipboards, hardboards Mineral wool boards 1 to 2 Blockboards, plywood Cement-bonded particle boards 1 to 2 3. Retighten the wing screw (4). Operating manual – portable circular saw PCSS 10-1400...
-
Page 17: Operation
Remove any oil before starting to saw to prevent oil residues from reaching the wood. • When sawing lightweight construction materials, observe the legal regulations and recommendations of the material manufacturers. Operating manual – portable circular saw PCSS 10-1400... - Page 18 When sawing U-profiles, you should start on the open side. Long profiles should be supported to prevent the saw blade from getting jammed and thus to avoid the risk of a kickback. Operating manual – portable circular saw PCSS 10-1400...
- Page 19 9. After completing the sawing operation, let go of the on/off switch (8) to stop the device. 7. Press the on/off switch (8) and hold it during operation. ð The device operates with the previously selected settings. Operating manual – portable circular saw PCSS 10-1400...
-
Page 20: Errors And Faults
The device becomes hot: • Check whether the chosen saw blade is suitable for the task to be carried out. • Keep the venting slots clear to prevent the motor from overheating. Operating manual – portable circular saw PCSS 10-1400... -
Page 21: Maintenance
Ensure that no moisture enters the housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth. Operating manual – portable circular saw PCSS 10-1400... - Page 22 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...