Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PRCS 10-850
Summary of Contents for Trotec PRCS 10-850
- Page 1 PRCS 10-850 OPERATING MANUAL SABRE SAW...
-
Page 2: Table Of Contents
Notice This signal word indicates important information (e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Operating manual – sabre saw PRCS 10-850... -
Page 3: Safety
There is an increased risk of electric shock if your body is earthed or grounded. • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Operating manual – sabre saw PRCS 10-850... - Page 4 • Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by your hand or against the body leaves it unstable and may lead to loss of control. Operating manual – sabre saw PRCS 10-850...
- Page 5 (see operating manual). out of the mains socket. Warning of electrical voltage We recommend using the power tool with original Trotec There is a risk of a short-circuit due to liquids accessories. penetrating the housing!
-
Page 6: Information About The Device
2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains. Operating manual – sabre saw PRCS 10-850... - Page 7 Quick-release chuck Caution LED work lamp Vibration emissions can cause a health hazard if the device is used for an extended period of time or if it is not properly handled and maintained. Operating manual – sabre saw PRCS 10-850...
-
Page 8: Transport And Storage
• ambient temperature below 40 °C than required for the cut. A narrow saw blade should be used • protected from dust and direct sunlight inside the transport when sawing tight curves. case Operating manual – sabre saw PRCS 10-850... - Page 9 3. Insert the saw blade into the quick-release chuck. Make sure that the teeth of the saw blade point downwards. 3. Set the locking lever (7) back to its initial position. 4. Check the guide shoe (10) for tight fit. Operating manual – sabre saw PRCS 10-850...
- Page 10 If you turn the handle, the saw blade can be inserted rotated by 180° (saw blade teeth point in the opposite direction) to enable easier working. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. Operating manual – sabre saw PRCS 10-850...
-
Page 11: Operation
After completing the sawing operation, switch off the power tool. • The saw blade should not be longer than required for the intended cut. ð The LED work lamp goes out. Operating manual – sabre saw PRCS 10-850... - Page 12 • Apply lateral pressure on the power tool until the bi-metal saw blade and the side of the guide shoe are positioned against the wall, see Schematic representation flush cutting. • Saw through the object applying constant lateral pressure. Operating manual – sabre saw PRCS 10-850...
- Page 13 • If required, allow the device to cool down. • Remove the tool from the tool holder (see Start-up chapter). • Clean the device according to the Maintenance chapter. • Store the device according to the Storage chapter. Operating manual – sabre saw PRCS 10-850...
-
Page 14: Errors And Faults
• The carbon brushes may be worn and have to be replaced. Do not immerse the device and the accessories in Contact the Trotec customer service or an electrically water. Make sure that no water or other liquids can skilled person. -
Page 15: Disposal
Operating manual – sabre saw PRCS 10-850... - Page 16 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...