Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PCSS 11-1200
Summary of Contents for Trotec PCSS 11-1200
- Page 1 PCSS 11-1200 ORIGINAL INSTRUCTIONS PORTABLE CIRCULAR SAW...
-
Page 2: Table Of Contents
This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. Note This signal word indicates important information (e.g. material damage), but does not indicate hazards. portable circular saw PCSS 11-1200... -
Page 3: Safety
Damaged or entangled cords increase the risk of electric shock. • When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. portable circular saw PCSS 11-1200... - Page 4 Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. portable circular saw PCSS 11-1200...
- Page 5 • Do not operate the power tool stationary. It is not build-up of debris. designed for operation with a saw table. • Do not use high speed steel (HSS) saw blades. Such saw blades can easily break. portable circular saw PCSS 11-1200...
- Page 6 Hold onto the mains plug while pulling the power cable out of the mains socket. We recommend using the power tool with original Trotec Warning of electrical voltage accessories. There is a risk of a short-circuit due to liquids...
-
Page 7: Information About The Device
2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains. portable circular saw PCSS 11-1200... - Page 8 • 1 x Carbide saw blade 24 teeth (for wood and plastic) • 1 x Rip fence • 1 x Adapter for dust extraction • 1 x SW6 Allen wrench • 1 x Replacement blade wrench • 1 x Manual portable circular saw PCSS 11-1200...
-
Page 9: Transport And Storage
• Clean the device as described in the Maintenance chapter. When the device is not being used, observe the following storage conditions: • dry and protected from frost and heat • ambient temperature below 40 °C • protected from dust and direct sunlight portable circular saw PCSS 11-1200... -
Page 10: Start-Up
Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. 3. Lock the locking lever (9) again. portable circular saw PCSS 11-1200... - Page 11 For mitre cuts, the cutting depth is smaller than the value shown on the cutting depth scale. 1. Release the locking lever for the cutting angle (2). 2. Set the desired cutting angle on the cutting angle scale (23). 3. Lock the locking lever (2) again. portable circular saw PCSS 11-1200...
- Page 12 3. Place the device on the front side of the motor housing. the clamping flange (17). 6. Then withdraw the replacement blade wrench (13). 7. Remove the clamping screw (18) together with the washer (24) as well as the clamping flange (17). portable circular saw PCSS 11-1200...
- Page 13 12. Please note that the lower guard (16) must be swung back using the retracting lever (20) in order to insert the saw blade. 14. Carefully swing the lower guard (16) back into its initial position with the retracting lever (20). portable circular saw PCSS 11-1200...
- Page 14 Meanwhile use the replacement blade wrench (13) to hold the clamping flange (17). 16. Place the clamping screw (18) together with the 19. Then withdraw the replacement blade wrench (13). washer (24) onto the clamping flange (17). 20. Check whether the saw blade is properly locked in place. portable circular saw PCSS 11-1200...
- Page 15 1. Loosen the wing screw (3) and insert the rip fence (15) into fence (15) and the arrow (27) on the base plate. the rip fence holder (4). The figure below shows a 4 cm setting by way of example: 45° 0° 3. Retighten the wing screw (3). portable circular saw PCSS 11-1200...
- Page 16 If required, the riving knife can be readjusted by means of the two set screws (28). < 5 mm 5 mm max. < 5 mm 5 mm max. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. portable circular saw PCSS 11-1200...
-
Page 17: Operation
Remove any oil before starting to saw to prevent oil residues from reaching the wood. • When sawing lightweight construction materials, observe the legal regulations and recommendations of the material manufacturers. portable circular saw PCSS 11-1200... - Page 18 11. After completing the sawing operation, let go of the on/off switch (7) to stop the device. 7. Press the on/off switch (7) and hold it during operation. ð The device operates with the previously selected settings. portable circular saw PCSS 11-1200...
-
Page 19: Errors And Faults
• Keep the venting slots clear to prevent the motor from overheating. Note Wait for at least 3 minutes after maintenance and repair work. Only then switch the device back on. portable circular saw PCSS 11-1200... -
Page 20: Maintenance
• Non-coated saw blades can be protected against corrosion by applying a thin layer of acid-free oil. Remove any oil before starting to saw to prevent oil residues from reaching the wood. portable circular saw PCSS 11-1200... -
Page 21: Declaration Of Conformity
Declaration of conformity In accordance with the EC Machinery Directive 2006/42/EC, Annex II, part 1, Section A Herewith, we – Trotec GmbH & Co. KG – declare that the machinery designated below was developed, constructed and produced in compliance with the requirements of the EC Machinery Directive in the version 2006/42/EC. - Page 23 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...