Table of Contents
Advertisement
Note: The Installer Remote shipped with the WU960H TV models
supports MMR operation. However, see item 098 PRO:CENTRIC
note regarding compatibility if you intend to configure the TV for
GEM Mode.
102 - ATSC BAND
Selects the RF band used by the ATSC tuner.
0 = Broadcast
1 = Cable
3 = IRC
4 = Same as NTSC (default)
103 - ATSC TUNE MODE
Sets the ATSC tuning mode. Set to 1 (default) for Physical Channel
tuning. Set to 0 for Virtual Channel tuning.
104 - START MINOR CHANNEL
When a digital (ATSC) Start Channel has been specified for item
004 STRT CHANNEL, this item sets the Minor Start Channel
number. Set to 0 when an analog (NTSC) Start Channel has been
specified for item 004.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 0 to use the default aspect ratio each time the TV is turned
ON (see item 096 DEF. ASP. RATIO). If set to 1, the aspect ratio
set before the TV was turned OFF will be the current aspect ratio
when the TV is turned ON again.
107 - BANNER SELECT
Selects the type of banner to display during channel change.
Set to 1 for channel label display, plus channel information (full
banner). Set to 0 for channel label display only (small banner).
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes
(blank screen) when no signal is present.
117 - FACT DEFAULT (Factory Default)
Set to 1 and press the Wheel (OK) button to restore the factory
default settings of all Installer Menu items. Once complete, the
value returns to 0.
Caution: If set to 1, this clears all Installer Menu custom
settings and restores the factory default settings. It
also clears the channel lineup, including any assigned
channel icons and custom text labels.
Note: See also Reference section, "Restoring Factory Defaults on
the TV(s)," for further information.
*
PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
206-4335
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. If left at the default value (255), the TV's Data Channel
Auto Search feature will be enabled (see additional information
below). *
Data Channel Auto Search feature: When this item is set to 255
2 = HRC
(default), once every 24 hours, the TV will initiate a search of 10
predefined channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to find the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server's
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 UPDATE TIME HR. See item
121 description for further information.
Note: Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. While Pro:Centric
updates are in progress, it is not possible to turn ON the TV.
Note: The Data Channel is automatically set to "253" if Media
Type is set to "IP" either in the EZ-Manager Wizard or in the IP
Environment / Pro:Centric Menu on the TV (see "EZ-Manager
Wizard" on pages 23 to 33 or "Pro:Centric Setup" on pages 70 to
72, respectively) or if Installer Menu item #119 Data Channel is
set to "IP Address" or "IP Domain Name" in the Cloud Configuration
Tool, which is typically used to configure TV CPUs for FTG Mode
operation. It is not possible to change the value to "253" directly in
the Installer Menu.
121 - UPDATE TIME HR
Based on the settings of this item and item 122 UPDATE TIME MN,
the Wake For Update feature wakes the TV once daily to check for
and, if applicable, download updates from the Pro:Centric server.
Set the Wake For Update hour from 0 to 23. This item uses the
24-hour clock format. The value "128" (default) is displayed as
"OFF." Directly entering 128 resets the default value (OFF) for this
item, though note that this setting does not mean the TV will not
initiate update events—see additional information below.
Under standard TV OFF/ON operating conditions (i.e., item 002
AC ON is set to 0), a Wake For Update event occurs when the TV
is OFF and causes the TV's CPU to temporarily turn ON, perform
the update cycle, and then turn back OFF, all while the TV appears
to be OFF. If item 002 AC ON is set to 2, 3, 18, or 19 for Instant
ON, then the TV's CPU is always ON and Wake For Update occurs
when the TV is in its Muted ON state (i.e., the TV only appears to
be OFF). The Wake For Update event causes the TV's CPU to
reboot in order to perform the update cycle and then return to its
Muted ON state. See also description for item 002.
Installer Menu (Cont.)
47
Advertisement
Table of Contents
