Extron electronics PI 140 Installation Manual

PI 140 Power Supply • Installation Guide
Important Safety Instructions
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product enclosure that may present a risk of
electric shock. On the product, risk of shock may
be indicated by this symbol.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this device apparatus during lightning storms or when unused for
long periods of time.
CAUTION:
To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases shall be placed
on the apparatus.
ATTENTION :
Afin de réduire les risques d'incendie
ou de choc électrique, protégez cet appareil de la pluie ou
de l'humidité. Cet appareil doit être conservé à l'abri des
éclaboussures et des projections, et aucun objet contenant un
liquide, tel qu'un vase, ne doit être posé sur l'appareil.
The Extron PI 140 Power Injector is a high output midspan power injector for Extron
products that have power requirements above class 3. It provides power over LAN
cabling. This guide provides instructions for an experienced installer to install and
connect the PI 140.
100-240V~50/60 Hz
1.1A MAX
INPUT OUTPUT
LAN POWERED TLP
Rear Panel
Installation
Step 1 — Mounting
ATTENTION:
• These power supplies are not suitable for use in air handling spaces or
in wall cavities. The power supply must be located within the vicinity of
the Extron AV equipment in an ordinary location with pollution degree 2,
and secured to an equipment rack within a dedicated closet, podium, or
desk.
• Ces sources d'alimentation ne sont pas appropriées pour une utilisation
dans les espaces d'aération ou dans les cavités murales. Cette source
d'alimentation doit être située à proximité de l'équipement audiovisuel
d'Extron, dans un endroit ordinaire avec une pollution IEC 1010 degré 2,
et fixé à un équipement de rack au sein d'un placard, d'une estrade ou
d'un bureau qui lui est dédié.
• The installation must be in accordance with the applicable provisions
of National Electrical Code ANSI/NFPA 70, article 725 and Canadian
Electrical Code part 1, section 16. The power supply must not be
permanently fixed to building or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui
s'applique au National Electrical Code ANSI/NFPA 70, article 725, et au
Canadian Electrical Code, partie 1, section 16. La source d'alimentation
ne devra pas être fixée de façon permanente à une structure de
bâtiment ou à une structure similaire.
• The PI 140 is intended for indoor use only. No part of the network that
uses XTP remote power can be routed outdoors.
• Le PI 140 est destiné à une utilisation en intérieur seulement. Aucune
partie du réseau qui utilise l'alimentation XTP à distance ne peut être
routée en extérieur.
Using the ZipClip 300
To attach the power supply to the ZipClip 300 mounting clip:
1. Insert the bottom of the power supply down into the
clip, starting with one end.
2. Pivot the other end down and press until
the clip snaps into place.
To remove the power supply from the
ZipClip:
1. Press the tab on the ZipClip.
2. Pivot the power supply and lift it out
of the ZipClip.
To fasten the tie wraps for cable
strain relief:
1. Attach the power supply to the
ZipClip 300 mounting clip as
described previously.
2. Fasten the power output cords to
the ZipClip base.
a. Insert tie wraps ("zip ties") along the
notches on the side of the power supply
and through the tie wrap anchor points on
the ZipClip, then around the cord.
b. Connect and pull the tie wraps until they are secure.
Do not over tighten.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as when
the power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
CAUTION:
This apparatus is a Class I product.
This product must be connected to a mains socket outlet with
a protective earthing connection.
ATTENTION :
Cet appareil est un produit de
Classe 1. Ce produit doit être connecté à une prise femelle
secteur équipée d'une connexion de mise à la terre.
The mains plug is used as the disconnect device and shall remain
readily operable.
To prevent the risk of shock, do not attempt to service this equipment
yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
CAUTION:
Power sources — This equipment should be operated only from
the power source indicated on the product. This equipment
is intended to be used with a main power system with a
grounded (neutral) conductor. The third (grounding) pin is a
safety feature, do not attempt to bypass or disable it.
Power disconnection — To remove power from the equipment
safely, remove all power cords from the rear of the equipment,
or the desktop power module (if detachable), or from the
power source receptacle (wall plug).
ATTENTION :
Les sources d'alimentation — Ce matériel ne devrait être alimenté
qu'à partir de la source d'alimentation stipulée sur le produit.
Ce matériel est prévu pour être relié à un circuit d'alimentation
général doté d'un conducteur (neutre) mis à la terre. La
troisième broche (de terre) est un composant de sécurité.
N'essayez pas de l'éviter ou de la désactiver.
Déconnection de l'alimentation — Pour déconnecter le matériel
de sa source d'alimentation en toute sécurité, débranchez
tous les cordons d'alimentation de l'arrière du matériel ou
débranchez l'adaptateur secteur (si débranchable) ou de la
prise secteur (prise murale).
Front Panel
2
PI 140 with
ZipClip 300
1
IN
P U
T
IN
P U
LA T
N
O U
P O P O TP
W ER W ER U T
ED ED
TL TL
P P
ZipTies
Mounting to Rack Rails Using a ZipClip
1. Fasten the ZipClip 300
mounting clip to a rack rail
using two rack screws
as shown in the
diagram on the right.
2. Insert the bottom of
the power supply
down into
the clip, starting with
one end.
Side of Rack
3. Pivot the other end
toward the clip and
press until the clip
snaps into place.
Mounting to a Rack Shelf
These power supplies are one-quarter rack
wide. Up to four power supplies can be
mounted side by side directly onto a rack
shelf.
1. Align the threaded holes in
the bottom of the power
supply with the holes
in an Extron rack shelf.
Fasten the supply to the
shelf with two
4-40 x 3/16 inch screws
as shown on the right.
2. Bolt the rack shelf to the
rack.
Furniture Mounting
NOTE:
The ZipClip is shipped with a
set of four wood screws.
1. Attach the ZipClip to the furniture using
two or more wood screws as shown at
right. Make sure the clip is oriented with
the appropriate side facing the mounting
surface and with the tab accessible from
the front of the furniture.
2. Insert the power supply into the ZipClip
as described previously and press to
snap it into place.
Step 2 — Cabling
ATTENTION:
Do not connect these devices to a computer data or
z
telecommunications network.
Ne connectez pas ces appareils à des données informatiques ou à un
z
réseau de télécommunications.
Twisted Pair Recommendations
For the best performance, see
1. Connect the Input port of the power
injector to the network or XTP
device using a CATx cable.
2. Connect a CATx cable between
Output port on the power injector
and the Extron device that requires
power from an external source.
3. Connect AC power to the PI 140.
Features
Indicators
1
Front panel power LED indicator —
Lights to indicate the PI 140 is receiving
power.
2
Rear panel PWR LED indicator —
Lights or blinks to indicate various power
states of the connected endpoints (see
the table below for LED states).
LED State
Unlit The endpoint is not connected or cannot be powered.
Lit The endpoint is receiving power from the PI 140.
Blinking There is a power overload fault, or power allocation is
exceeded.
ZipClip 300
Back of Rack
Inside a Rack
RSB 123
Rack Shelf
(2) 4-40 x 3/16"
Screws
Rack Mounted
Under a Desk
PI 140
on page 2.
3 1 2
100-240V~50/60 Hz
1.1A MAX
INPUT OUTPUT
LAN POWERED TLP
To an Extron Device
To Network or
That Requires an
XTP Device
External Power Supply
1 1
IN P U
2 2 LA T
N
P O
W E
R E
D
TL
P
Port Status
1