Milnor MWF63J7 Installation And Service
  1. Manuals
  2. Brands
  3. Milnor Manuals
  4. Washer
  5. MWF63J7
  6. Installation and service

Milnor MWF63J7 Installation And Service

Hide thumbs Also See for MWF63J7:
Table of Contents

Advertisement

Quick Links

Download this manual
Manual Number: MCWMCA01
Edition (ECN): 2023216
Installation, Parts, and
Service
MWF63J7, MWF63Z7,
MWF77J7, MWF77Z7
PELLERIN MILNOR CORPORATION
Post Office Box 400, Kenner, Louisiana 70063–0400, U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Milnor MWF63J7

Summary of Contents for Milnor MWF63J7

  • Page 1 Manual Number: MCWMCA01 Edition (ECN): 2023216 Installation, Parts, and Service MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 PELLERIN MILNOR CORPORATION Post Office Box 400, Kenner, Louisiana 70063–0400, U.S.A.

  • Page 3: Table Of Contents

    MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; ..................18 MWF63J7/Z7; MWF77J7/Z7 Covers ..............21 MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 Shipping Brackets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; ....................24 MWF77J7, MWF77Z7. Torque Requirements for Fasteners ..................26 Torque Values .........................26 Fasteners Made of Carbon Steel ................26 Without a Threadlocker ..................26 With a Threadlocker ..................28...
  • Page 4 Utility Requirements and Related Information ..............48 Plumber Precautions.......................49 Electrician Precautions ....................50 Chemical Supplier Precautions..................51 4 Drive Assemblies.........................52 Drive MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, .........................53 MWF77Y7 Bearing Assembly & Installation MWF36, MWF45, MWF63, MWF77 ......54 5 Suspension...........................61 Suspension MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, .........................62...
  • Page 5 Contents 5 Compartment Supply MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; ......78 MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 8 Water and Steam..........................80 Water and Steam MWF63J7, MWF63Z7, MWF63C7, MWF63Y7, MWF77J7, MWF77Z7, ....................81 MWF77C7, MWF77Y7 Drain Valve to Rear MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7;...
  • Page 6 MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, ....75 MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Table 25 Parts List—Peristaltic Supply MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, ........................77 MWF77Y7. Table 26 Parts List—5 Compartment Supply MWF36J8, MWF36Z8; MWF45J8, MWF45Z8;...

  • Page 7: General Service And Safety Related Components

    1 General Service and Safety Related Components Pellerin Milnor Corporation...

  • Page 8: Limited Standard Warranty

    General Service and Safety Related Components BMP720097 / 19036 BRUUUM01.1 0000229985 D.2 D.6 12/5/19, 11:43 AM Released Pellerin Milnor Corporation...

  • Page 9: How To Get The Necessary Repair Components

    Email: parts@milnor.com BNUUUU02 / 2021104A BNUUUU02 0000158094 3/3/21, 9:47 AM Released Trademarks BNUUUU02.R01 0000158093 E.2 D.2 F.2 3/3/21, 9:47 AM Released These words are trademarks of Pellerin Milnor ® Corporation and other entities: Table 1. Trademarks AutoSpot™ GreenFlex™ MilMetrix ®...

  • Page 10: Safety - Suspended Washer Extractors

    The goods are normally isolated by the locked cylinder door. Do not attempt to open the door or reach into the cylinder until the cyl- � inder is stopped. Pellerin Milnor Corporation...
  • Page 11 Processing can cause solvent- containing goods to give off flammable vapors. Do not use flammable solvents in processing. � Do not process goods containing flammable substances. Consult with � your local fire department/public safety office and all insurance providers. Pellerin Milnor Corporation...

  • Page 12: Safety Alert Messages-Unsafe Conditions

    � WARNING: Explosion Hazards — Cylinder—A damaged cylinder can rip apart dur- ing extraction, puncturing the shell and discharging metal fragments at high speed. Do not operate the machine with any evidence of damage or � malfunction. Pellerin Milnor Corporation...

  • Page 13: Careless Use Hazards

    Abide by the current OSHA lockout/tagout standard when lockout/tag- � out is called for in the service instructions. Outside the USA, abide by the OSHA standard in the absence of any other overriding standard. Pellerin Milnor Corporation...

  • Page 14: Installation Tag Guidelines

    Read the manuals before proceeding. This symbol appears on most tags. The machine ships with safety, operator, and routine maintenance guides for customer use. Milnor dealer manuals for installing, commissioning, and servicing the machine are also available from the Milnor Parts department.
  • Page 15 Otherwise, reverse the electric power connections, as ex- plained in the schematic manual. B2TAG94099: Do not strike the shell door when fork-lifting. This can cause the door to leak. B2T2001013: Hot water connection. B2T2001014: Cold water connection. B2T2001015: Reuse (third) water connection. Pellerin Milnor Corporation...
  • Page 16 Water hammer can rupture the water inlet valves on this machine. Follow applicable codes when installing water hammer arresters. Maintain incoming water pressure between 10 and 75 psi (between 0.7 and 5.1 bar). Pressures outside this range can damage the water valves in this machine. Pellerin Milnor Corporation...

  • Page 17: Safety Placards And Locations

    Released Safety Placards and Locations 3 Sheet MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; MWF63J7/Z7; MWF77J7/Z7 NOTICE: Replace placard immediately, if removed or unreadable. Approximate loca- tions of placards are shown. If aluminum placard, mounting holes are provided on machine. Use #8 self-tapping screws.
  • Page 18 General Service and Safety Related Components Safety Placards and Locations 3 Sheet MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; MWF63J7/Z7; MWF77J7/Z7 Legend A... Front view B... Rear view C... Alternate location Pellerin Milnor Corporation...

  • Page 19: Mwf63J7/Z7; Mwf77J7/Z7

    General Service and Safety Related Components Safety Placards and Locations 3 Sheet MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; MWF63J7/Z7; MWF77J7/Z7 Table 2. Parts List—Safety Placards Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 20: Safety Placards And Locations Iso

    Released Safety Placards and Locations ISO 3 Sheet MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; MWF63J7/Z7; MWF77J7/Z7 NOTICE: Replace placard immediately, if removed or unreadable. Approximate loca- tions of placards are shown. If aluminum placard, mounting holes are provided on machine. Use #8 self-tapping screws.
  • Page 21 General Service and Safety Related Components Safety Placards and Locations ISO 3 Sheet MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; MWF63J7/Z7; MWF77J7/Z7 Legend A... Front view B... Rear view C... Alternate location Pellerin Milnor Corporation...

  • Page 22: Z8; Mwf63J7/Z7; Mwf77J7/Z7

    General Service and Safety Related Components Safety Placards and Locations ISO 3 Sheet MWF18J8; MWF27J8/Z8; MWF36J8/Z8; MWF45J8/Z8; MWF63J7/Z7; MWF77J7/Z7 Table 3. Parts List—Safety Placards ISO Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 23: Covers Mwf63J7, Mwf63Z7, Mwf77J7, Mwf77Z7

    General Service and Safety Related Components BPWMCM01 / 2022182 BPWMCM01.1 0000417569 A.4 D.2 4/25/22, 2:26 PM Released Covers 3 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 Pellerin Milnor Corporation...
  • Page 24 General Service and Safety Related Components Covers 3 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 Pellerin Milnor Corporation...

  • Page 25: Mwf63J7, Mwf63Z7, Mwf77J7, Mwf77Z7

    General Service and Safety Related Components Covers 3 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 Table 4. Parts List—Covers Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations.

  • Page 26: Shipping Brackets

    Released Shipping Brackets 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7. NOTE: Before operating, remove the shipping brackets (painted red). The shipping brack- ets may be retained in the event the machine must be moved. See BNWUUI03. Legend Ā–A .

  • Page 27: Mwf36J8, Mwf36Z8; Mwf45J8, Mwf45Z8; Mwf63J7, Mwf63Z7; Mwf77J7, Mwf77Z7

    General Service and Safety Related Components Shipping Brackets 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7. Table 5. Parts List—Shipping Brackets Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 28: Torque Requirements For Fasteners

    The document about the assembly gives the torque requirements for other fasteners. If fastener torque specifications or threadlocker requirements in an assembly document are different from this document, use the assembly document. ® Figure 1. The Bolts in Milnor Equipment Legend The Marks on Bolt Heads A...
  • Page 29 Torque Values for Plated Fasteners with Maximum 5/16-inch Diameters and No Lubricant The Grade of the Bolt Grade 2 Grade 5 Grade 8 Grade BC Pound-Inches Pound-Inches Pound-Inches Pound-Inches Dimension 1/4 x 20 – – 1/4 x 28 5/16 x 18 5/16 x 24 – – Pellerin Milnor Corporation...

  • Page 30: With A Threadlocker

    Table 10. Threadlocker by the Diameter of the Bolt (see below Note ) Dimension 1/4-inch 1/4- to 5/8-inch 5/8- to 7/8-inch 1-inch + LocTite Product LocTite 222 LocTite 242 LocTite 262 High temperature LocTite 272 LocTite 277 Pellerin Milnor Corporation...
  • Page 31 Torque Values if You Apply LocTite 272 (High-Temperature) The Grade of the Bolt Grade 2 Grade 5 Grade 8 Grade BC Pound-Feet Pound-Feet Pound-Feet Pound-Feet Dimension 1 x 8 1222 1272 1725 1114 1510 1 x 12 1337 1392 1887 – – Pellerin Milnor Corporation...

  • Page 32: Stainless Steel Fasteners

    BNUUUN02.C06 0000222445 A.3 B.3 D.2 1/2/20, 2:14 PM Released Table 16. Torque Values for Stainless Steel Fasteners 5/16-inch and Smaller 316 Stainless 18-8 Stainless 18-8 Stainless with Loctite 767 Pound-Inches Pound-Inches Pound-Inches Dimension 1/4 x 20 1/4 x 28 5/16 x 18 5/16 x 24 Pellerin Milnor Corporation...

  • Page 33: Preparation

    1. Clean all threads with a wire brush or a different tool. 2. Remove the grease from the fasteners and the mating threads with solvent. Make the parts dry. NOTE: LocTite 7649 Primer or standard solvents will remove grease from parts. Pellerin Milnor Corporation...

  • Page 34: How To Apply A Threadlocker

    5/16-inch and Smaller, page 30 Through Holes BNUUUN02.T04 0000222506 A.3 B.3 D.2 11/26/19, 2:51 PM Released 1. Put the bolt through the assembly. 2. Apply the threadlocker only to the bolt thread area that will engage the nut. Pellerin Milnor Corporation...

  • Page 35: Figure 3 Apply Threadlocker In A Through Hole

    For low-strength and moderate-strength threadlocker, disassemble with hand tools. Figure 4. Use heat for disassembly of fasteners with threadlocker. Legend Apply Heat to a Small Area A... How to apply heat to a small fastener B... How to apply heat to a large fastener Pellerin Milnor Corporation...

  • Page 36: Important Installation Precautions

    Use the next larger size for runs 50 to 100 feet (15 to 30 meters). Use wire two sizes larg- er for runs greater than 100 feet (30 meters). If an inverse time circuit breaker is used and local codes require a larger wire size than that specified by Milnor, abide by the local code. Pellerin Milnor Corporation...

  • Page 37: Ground

    Structures by Laundering Machines BNUUUI01.C01 0000189336 A.5 C.3 D.2 1/2/20, 2:14 PM Released ® This document replaces Milnor document BIWUUI02. All laundering machines impart static and dynamic forces to the supporting structures (foundation and soil, floor, and building). Static forces include the machine weight plus the weight of the goods and water.

  • Page 38: Disclaimer Of Responsibility

    Important Installation Precautions Disclaimer of Responsibility BNUUUI01.C02 0000189359 B.3 C.3 D.2 1/2/20, 2:14 PM Released Pellerin Milnor Corporation accepts no responsibility for damage or loss as a result of: • inadequate supporting structures • interference with the use of the facility caused by machine operation The facility owner/operator is solely responsible to ensure that: •...

  • Page 39: Primary Information Sources

    NOTICE: All data is subject to change without notice and may have changed since last printed. It is the responsibility of the potential owner/operator to obtain written confirma- tion that any data furnished by Milnor ® applies for the model number(s) and serial num- ber(s) of the purchased machine(s).

  • Page 40: How Chemical Supplies Can Cause Damage

    The company that does these procedures must make sure that these procedures do not cause dam- age. Pellerin Milnor Corporation accepts no responsibility for chemical damage to the ma- chines it makes or to the goods in a machine.

  • Page 41: Figure 6 Incorrect Configurations That Let The Chemical Supply Go In The Ma

    Figure 6. Incorrect Configurations That Let the Chemical Supply Go In the Machine by a Siphon Schematic Views Legend P... Pump T... Chemical tank S... The siphon occurs above here. Liquid in the gray parts of the chemical tube and tank can go in the machine. Pellerin Milnor Corporation...

  • Page 42: Equipment And Procedures That Can Prevent Damage

    — There is a manifold on the machine to at- tach chemical tubes from a chemical pump system. The manifold has a source of water to flush the chemical supplies with water. Figure 8. Examples of Manifolds for Chemical Tubes. Your equipment can look different. Pellerin Milnor Corporation...

  • Page 43: Close The Line

    Chemical tank Prevent leaks. — When you do maintenance on the chemical pump system: • Use the correct components. • Make sure that all connections are the correct fit. • Make sure that all connections are tight. Pellerin Milnor Corporation...

  • Page 44: Installation Procedures

    Disclaimer — Pellerin Milnor Corporation is not responsible for damage to the machine after it leaves the factory. Pellerin Milnor Corporation strongly recommends that the consignee (usually the owner/management) carefully inspect the machine in its protective wrapping before off-loading and inspect the uncovered machine after off-loading. If damage occurred in transit, ensure that the transportation company acknowledges the damage in writing.

  • Page 45: Facility Prerequisites

    See the machine dimensional drawing, which can be found at the end of the installation manual, for overall dimensions. Partial dis- assembly is sometimes possible. Contact the Milnor ® Service department.
  • Page 46 Know and accommodate the Use lifting and moving equipment appropriate for the machine machine shipping weight. shipping weight, as shown on the Bill of Lading. To obtain the shipping weight in advance, contact the Milnor ® Transportation department. Use only lifting eyes for crane Machines designed for crane lifting are provided with lifting lifting.

  • Page 47: Technician Precautions

    Check for and remove shipping tie wraps. � Check for and remove suspension hold-down hardware, if applicable. � Check for and remove red shipping brackets, if applicable. � See the “Cylinder inspection” warning and inspect the cylinder for smoothness. � Pellerin Milnor Corporation...
  • Page 48 Check for and remove sus- See also the service manual. Example: pension hold-down hard- ware, if applicable. Check for and remove red Shipping brackets are painted red. See the shipping brackets parts shipping brackets, if document in the service manual. applicable. Pellerin Milnor Corporation...

  • Page 49: Can The Door(S) Be Opened Before Utilities Are Connected

    Connection Precautions for Washer-extractors BNWUUI04.C01 0000255071 B.2 C.2 D.2 8/2/21, 10:05 AM Released This document supersedes documents BNWBUI01, BNWBUI02, BNWBUI03, BNWBUI04, BIRQVI01, BIMUUI02, and BIIFUI01. It applies to all Milnor ® washer-extractor models in pro- duction as of October 1, 2019.

  • Page 50: Notices

    — This document and the documents it references address common tasks that the plumber, electrician, and chemical supplier will perform. Other tasks, not explained here, can be needed. Information about these tasks is usually provided by the dealer, the Milnor ®...

  • Page 51: Plumber Precautions

    Foreign material such as debris in air lines, trapped air in water lines, and condensate in steam lines can damage machine components. Do not twist valve Hold a wrench on the valve side of a pipe connection to prevent the bodies. valve from twisting when you tighten the connection. Pellerin Milnor Corporation...

  • Page 52: Electrician Precautions

    Confirm the reliability of the electric service. � Confirm the machine is phased in correctly. � Confirm the correct line voltage setting on a selectable 240/208 volt machine. � Attach the stinger leg, if any, only to L3. � Pellerin Milnor Corporation...

  • Page 53: Chemical Supplier Precautions

    BIWUUI03 is also available at: https://milnor.sharefile.com/d-s79f12e8f11f42a9b Understand the machine The machine controller is explained in detail in the reference manual controller. for your machine, which is available from the Milnor ® Parts department. Pellerin Milnor Corporation...

  • Page 54: Drive Assemblies

    4 Drive Assemblies Pellerin Milnor Corporation...

  • Page 55: Drive

    4/20/22, 8:19 AM Released Drive 1 Sheet MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Table 18. Parts List—Drive Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 56: Bearing Assembly & Installation Mwf36, Mwf45, Mwf63, Mwf77

    Drive Assemblies BPWMCB01 / 2022354 BPWMCB01.1 0000161056 8/24/22, 6:08 PM Released Bearing Assembly & Installation MWF36, MWF45, MWF63, 4 Sheet MWF77 Pellerin Milnor Corporation...
  • Page 57 Q. Apply silicone between the inner shell front and the shell, fully around the hole pattern. R. Apply adhesive to the bolt, torque to 909 FT. LBS. S. Apply silicone between the bearing housing and the shell rear, fully around the hole pattern. Pellerin Milnor Corporation...
  • Page 58 Bearing Assembly & Installation MWF36, MWF45, MWF63, 4 Sheet MWF77 D. Connection between the cylinder rear and the bearing housing E. Connection between the bearing housing and the pulley R. Apply adhesive to the bolt, torque to 282 FT. LBS. W. Key Pellerin Milnor Corporation...
  • Page 59 Drive Assemblies Bearing Assembly & Installation MWF36, MWF45, MWF63, 4 Sheet MWF77 Pellerin Milnor Corporation...
  • Page 60 SLEEVE DELRIN 6MM 98CX961460 TUBE INSERT 4MM 98CX932801 PIPE FITTING, 6.5X1/4 BSP 15U281A WASHER=CLIPPED 1/2 ID .06THK 01 10025Z NPLT:BEARING&SEAL LUB-42"& 36" 98CX931701 HEXBUSH, 1/4X1/8 BRASS BSP 98CX961708 GREASE FITTING, 1/8BSP ZINC 98CX910823 FLEXIBLE TUBING, 4X6MM OD Pellerin Milnor Corporation...
  • Page 61 TONGUE WASH TIM K91514 FOR N14 56ATW16 TONGUE WASH T#K91516 FOR AN16 56AHW114 TW114 BEARING LOCWASHER 56AHW116 TW116 BEARING LOCKWASHER 56AHN14 N14 BEARING LOCKNUT 56AHN16CM AN16 BEARING LOCKNUT, MWF77 60C169 ORING 7+3/4ID1/8 BUNA70 #265 60C160J ORING 6+1/4ID1/8CS BUNA70 #259 Pellerin Milnor Corporation...
  • Page 62 Used In Item Part Number Description/Nomenclature Comments 15K039M HXCAPSCR M6X20, 8.8,ZINC 15U180 LOCKWASHER MEDIUM 1/4 ZINCPL 15K117MS HXCAPSCR M10X35 SS 18-8 15U266MS FLTWSHR METRIC D10 SS18-8 02 21546 EXCLUDER SEAL GASKET 02 21047 GASKET=FRNT SEAL HOLDR 4232F Pellerin Milnor Corporation...

  • Page 63: Suspension

    5 Suspension Pellerin Milnor Corporation...

  • Page 64: Suspension

    Suspension BPWMCJ01 / 2022182 BPWMCJ01.1 0000418172 A.4 D.2 4/25/22, 3:49 PM Released Suspension 2 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 MWF77J7, MWF77Z7, MWF77C7, MWF77Y7 MWF63J7, MWF63Z7, MWF63C7, MWF63Y7 Legend A... Rear B... Front C... Typical Pellerin Milnor Corporation...
  • Page 65 Suspension Suspension 2 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Table 20. Parts List—Suspension Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations.

  • Page 66: Shocks

    Suspension BPWMCJ02 / 2022173 BPWMCJ02.1 0000418858 A.3 D.2 4/20/22, 8:32 AM Released Shocks 2 Sheets MWF63J8, MWF63Z8, MWF77J8, MWF77Z8 Rear Shocks Front Shocks Pellerin Milnor Corporation...
  • Page 67 "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations. Description/Nomenclature Used In Item Part Number Comments Components 60BS6838 SHOCK ABSORBER = ARVIN #65907340E 60BS6832 SHOCK ABSORBR GABRIEL #65488440X Pellerin Milnor Corporation...

  • Page 68: Door Assemblies

    6 Door Assemblies Pellerin Milnor Corporation...
  • Page 69 This page intentionally blank...

  • Page 70: 26" Door

    Door Assemblies BPWMCD02 / 2023092 BPWMCD02.1 0000418850 B.2 D.2 2/27/23, 4:50 PM Released 26” Door 4 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Pellerin Milnor Corporation...
  • Page 71 Door Assemblies 26” Door 4 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Pellerin Milnor Corporation...
  • Page 72 Door Assemblies 26” Door 4 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Pellerin Milnor Corporation...
  • Page 73 Door Assemblies 26” Door 4 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7, MWF63C7, MWF63Y7, MWF77C7, MWF77Y7 Table 22. Parts List—Installation 26” Door Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 74: Door Latch

    0000410502 B.2 D.2 8/24/22, 6:26 PM Released Door Latch 1 Sheet MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Legend A... Table 23. Parts List—Door Latch Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 75: Chemical Supply

    7 Chemical Supply Pellerin Milnor Corporation...

  • Page 76: Soap Chute

    Chemical Supply BPWMBC01 / 2022354 BPWMBC01.1 0000410689 B.2 D.2 8/24/22, 6:45 PM Released Soap Chute 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Pellerin Milnor Corporation...
  • Page 77 Chemical Supply Soap Chute 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Table 24. Parts List—Soap Chute Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 78: Mwf77J7, Mwf77Z7; Mwf63C7, Mwf63Y7; Mwf77C7, Mwf77Y7

    BPWMBC02 / 2022354 BPWMBC02.1 0000410775 B.2 D.2 8/24/22, 6:49 PM Released Peristaltic Supply 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7. Figure 10. Peristaltic Diagram Legend A-A . . Cross section C... Cold water line E...

  • Page 79: Figure 11 Peristaltic Inlet

    Chemical Supply Peristaltic Supply 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7. Figure 11. Peristaltic Inlet Legend Cross Section B-B . . Cross section K... Vent L... Air space: 1 inch (25MM) Table 25.

  • Page 80: Compartment Supply

    Chemical Supply BPWMBC03 / 2022354 BPWMBC03.1 0000410771 B.2 D.2 8/24/22, 6:53 PM Released 5 Compartment Supply 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Pellerin Milnor Corporation...
  • Page 81 Chemical Supply 5 Compartment Supply 2 Sheets MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7; MWF63C7, MWF63Y7; MWF77C7, MWF77Y7 Table 26. Parts List—5 Compartment Supply Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 82: Water And Steam

    8 Water and Steam Pellerin Milnor Corporation...

  • Page 83: Water And Steam

    Water and Steam BPWMCW01 / 2023194A BPWMCW01.1 0000420008 C.2 D.2 5/11/23, 3:05 PM Released Water and Steam 3 Sheets MWF63J7, MWF63Z7, MWF63C7, MWF63Y7, MWF77J7, MWF77Z7, MWF77C7, MWF77Y7 Legend A... Hot water for supply B... C... Cold D... Steam E... Drain trough F...
  • Page 84 Water and Steam Water and Steam 3 Sheets MWF63J7, MWF63Z7, MWF63C7, MWF63Y7, MWF77J7, MWF77Z7, MWF77C7, MWF77Y7 Legend A... Hot water for supply B... C... Cold D... Steam Pellerin Milnor Corporation...
  • Page 85 Water and Steam Water and Steam 3 Sheets MWF63J7, MWF63Z7, MWF63C7, MWF63Y7, MWF77J7, MWF77Z7, MWF77C7, MWF77Y7 Tilt Washer Legend D... Steam K... Water from peristaltic Table 27. Parts List—Water & Steam Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 86: Drain Valve To Rear

    Released Drain Valve to Rear 1 Sheet MWF36J8, MWF36Z8; MWF45J8, MWF45Z8; MWF63J7, MWF63Z7; MWF77J7, MWF77Z7 Table 28. Parts List—Drain Valve to Rear Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 87: Pneumatic Assemblies

    9 Pneumatic Assemblies Pellerin Milnor Corporation...

  • Page 88: Pneumatic Schematic

    Pneumatic Assemblies BPWMCP01 / 2022184 BPWMCP01.1 0000420135 A.4 D.2 4/28/22, 7:56 AM Released Pneumatic Schematic 2 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 Schematic Legend A... Door seal B... Door latch C... Hot water line D... Cold water line E... Steam line F...
  • Page 89 Pneumatic Assemblies Pneumatic Schematic 2 Sheets MWF63J7, MWF63Z7, MWF77J7, MWF77Z7 Table 29. Parts List—Pneumatic Schematic Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations.

  • Page 90: 10 Control And Sensing

    10 Control and Sensing Pellerin Milnor Corporation...

  • Page 91: Water Level & Temperature Sensor

    Control and Sensing BPWMBZ01 / 2022062 BPWMBZ01.1 0000407434 A.3 D.2 1/31/22, 1:43 PM Released Water Level & Temperature Sensor 1 Sheet MWF45J8/Z8, MWF63J7/Z7, MWF77J7/Z7, MWF100J7/Z7, MWF125J7/Z7; MWF45C8/Y8, MWF63C7/Y7, MWF77C7/Y7, MWF100C7/Y7, MWF125C7/Y7 Legend A... To transducer B... Temperature probe C... Transducer Table 30.

  • Page 92: Mwf45J8/Z8, Mwf63J7/Z7, Mwf77J7/Z7, Mwf100J7

    Control and Sensing Water Level & Temperature Sensor 1 Sheet MWF45J8/Z8, MWF63J7/Z7, MWF77J7/Z7, MWF100J7/Z7, MWF125J7/Z7; MWF45C8/Y8, MWF63C7/Y7, MWF77C7/Y7, MWF100C7/Y7, MWF125C7/Y7 Table 30 Parts List—Water Level & Temperature Sensor (cont'd.) Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all"...

  • Page 93: Dimensional Drawings

    11 Dimensional Drawings Pellerin Milnor Corporation...
  • Page 94 This page intentionally blank...

This manual is also suitable for:

Mwf63z7Mwf77j7Mwf77z7

Table of Contents