PrimeCables CAB-ET101 - Indoor Furnishing Installation Guide

Technical Data

Accessory kit

Note: The drawings below are only for reference and may be slightly different with the object, please in kind prevail. Any tools missing or installation problems, please contact the customer service freely.

Part list

Installation instruction

1. Use 4 PCS of Hexagon Socket Button Head Screws(A) to connect "L" Marked Desk Foot(1) and "L" Marked Desk Leg(2), and use a 4*4 Wrench(D) to fasten.
   Similarly, use 4 PCS of Hexagon Socket Button Head Screws (A) to connect "R" Marked Desk Foot (1) and "R" Marked Desk Leg (3), with arrows in the same directions, and use a 4*4 Wrench (D) to fasten.
   
   Attention: make sure both parts are heading the same direction
2. Put two hexagon joint levers (5) through left and right elements of the t able leg to two sided driving lever of motor element (4), lock it with locking fastener, as displayed in the photo.
   
   1. unscrew the plastic nut
      
   2. connect driving lever
   3. lock the plastic nut
3. Use 8 PCS of Hexagon Socket Button Head Screws(B) to connect Motor Module(4) to "L" Marked Leg Module and "R" Marked Leg Module respectively, and use a 3*3 Wrench(D) to fasten them. Motor Module (4) needs to be installed with Arrow label upward, do not misplace.
   
   Attention: while there's no access to install the drive link, try to use the 6x6 wrench(E) fine turning table legs to make hexagon direction same as motor element
   Motor Module(4) needs to be installed at the "Shorter Part" side, with Arrow label upward, do not misplace.
4. Install mounting plate(6) to "L" element of table leg by four hexagon socket button head screws (B), then fasten them by 3x3 wrench(D). Use the same way to install the right mounting plate(7) to the right.
   
   Attention: Marks are in the same direction
5. Using the 8pcs cross recessed countersunk head screw(C) to install the worksurface with the right (6)and left(7) support plate, and tight them by cross screwdriver or electric pistol drill.
   
   Attention: Worksurface is optional
6. Using the 6pcs cross recessed countersunk head screw (C) to install the control box(8) and the handset (9) with the worksurface, tight them by cross screwdriver or electric pistol drill. Pay attention to the installation direction of the control box and handset, and the connecting line range, should be as what is shown in the figure.
   
7. According to the graph above, connect the handset wire (9), Power Line (10) and Motor Wire (11) to the responding sockets in controller box (8).
   
   To make the wires in order, cable organizer (12) can be used to attach the wires to the desktop surface.

Control panel instruction

Handset

●	" "	Up, adjust the desk upwards
●	" "	Down, adjust the desk downwards
●	" "	Position 1, first height position saved by user
●	" "	Position 2, second height position saved by user
●	" "	Position 3, third height position saved by user
●	" "	Save, save height position
●	" "	Long time sitting remind button, remind of long time sitting

Instruction

• First reset before use, LED display shows " ", press" ▼ " and hold till the desk goes to the lowest and then go up to 75cm, display shows " ", reset done.
• After reset, use " ▲ "and " ▼ " to adjust the desk, display shows height, the height range is "75cm-123cm".
• Save:

1. Press "up" or "down" to your height, example " "
2. Press " ", display show " ", then press " " to save the height 80.0cm to position 1, display shows " "
3. Repeat a and b, save 100cm to position 2 and 120cm to position 3, display shows " "and " "
4. Press 1, 2, or 3 to adjust to saved heights.

• Long time sitting remind

1. Press "A", the remind is on, display shows " "
2. After 2 seconds, 45 minute countdown starts, display shows " " when it shows " ", there will be a 10 second beeping.
3. Within 10 second, press button to adjust, there will be another 45 minutes countdown, if no adjustment in 10 seconds, it will remind again after 5 minutes. If still no adjustment, then it won't remind again.
4. Press " " and hold for 3 seconds to shut the remind function, display shows " "

Common Faults Handling

Tips below can help you detect and eliminate common faults. If the fault happens to be not listed in the below chart, please contact the supplier. All the faults or turnovers can only be diagnosed and corrected by manufacturer and trained professionals.

Caution

1. Power supply: AC110V±10%,60HZ
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so dispose of it in accordance with each country's environmental legislation, not the general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when playing, so any dangerous consequences caused by this improper action will not be on
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g., do not litter the tools around. Always be careful to treat the packaging materials in order to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in transportation.

DISPOSAL

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download PrimeCables CAB-ET101 - Indoor Furnishing Installation Guide