Citizen G910 - Watch Abbreviated Manual
![]()
Component identification
![Citizen - G910 - Component identification Component identification]()
- This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
- To see details of charging time, specifications and operations, refer to the instruction manual.
- Actual appearance may differ from the illustration.
- The crown has two positions when pulling it out.
![]()
Checking the time with chimes
- You can not use this function while using the chronograph.
- Push the crown in to position
. - Press and hold the upper right button
for 2 seconds or more.
Combination of high and low tones of chimes tells you the time of the sub watch. - The 3 tones mean "hour", "quarter of hour" and "minute" as shown below.
- Meaning of the tones
Hight | Length | Meaning |
High | Long | "Hour" |
Low | Long | "minute" |
High-low combination | two short tones | "quarter of hour" |
- Ex.: 4: 36
![Citizen - G910 - Checking the time with chimes - Sound example Checking the time with chimes - Sound example]()
To stop the chimes
Press any button.
Setting the time and day of week
This watch is equipped with two watches: the main watch and the sub watch.
They control hands shown as follows.
| Hands |
Main watch | Hour, 24-hour, minute and second hands |
Sub watch | Chimes (Chronograph hour and minute hands when adjusting the time) |
- Pull the crown out to position
when the second hand points 0 second.
The second hand stops and the chronograph hour and minute hands indicate the hour and the minute of the sub watch respectively. - Rotate the crown to set the day of week of the main watch.
- The hour, minute and 24-hour hands move synchronously.
- Rotate the crown left and right and move the hour hand from PM 10 to AM 2 to move the day-of-week hand quickly.
- Rotate the crown to set the time of the main watch.
- Check whether the time set is AM or PM with the 24-hour hand.
- Press and release the lower right button
or the upper right button
to adjust the sub watch. - Each time you press button
, the hands move forward by 1 minute; each time you press the button
, they move back by 1 minute. - They move continuously while you are pressing and holding the button.
- Check whether the time set is AM or PM with the chronograph second hand.
![Citizen - G910 - Checking the chronograph hands for AM and PM Checking the chronograph hands for AM and PM]()
- Push the crown in to position
in accordance with a reliable time source.
The second hand starts moving.
Setting the year, month and date
- The calendar of this watch does not have to be adjusted manually until February 28, 2100 including leap years. (perpetual calendar)
- Day of week is set while setting the time of the main watch.
- Pull the crown out to position
. - Press and release the lower right button
or the upper right button
to adjust the date. - Each time you press button
, the date indication moves forward by 1 day; each time you press button
, it moves back by 1 day. - It moves continuously while you are pressing and holding the button.
- Press and release the lower left button
to adjust the year and month.
- Each time you press the button, the chronograph hour and minute hands move by 1 month.
- They move continuously while you are pressing and holding the button.
- The year corresponds to the years since leap year.
Year since leap year | Indication |
0 (leap year) | L.Y. |
1 year | 1 |
2 years | 2 |
3 years | 3 |
![Citizen - G910 - Setting the year, month and date Setting the year, month and date]()
Ex.: When setting it June of 1 year since the leap year
- Push the crown in to position
to finish the procedure.
Checking the reference position
- Push the crown in to position
. - Press and hold the lower right button
for 5 seconds or more.
The chronograph hour and minute hands show the time of the sub watch. - Press and release the lower right button
.
The chronograph hour, minute and second hands and date indication move to their current reference position.
- Correct reference positions:
Chronograph hour, minute and second hands: 12 o'clock position
Date indication: "1"
When the current reference position is different from the correct one, adjust the position following the steps of "Correcting the reference position".
- Press and release any button to finish the procedure.
- It returns to normal indication automatically in about 2 minutes without any operation.
Correcting the reference position
- Pull the crown out to position
.
The second hand stops. - Press and hold the lower left button
for 5 seconds or more.
The mode hand, sub-watch hour and minute hands move one by one and the alarm sounds. - Press and release the lower left button
repeatedly to change the hand/indication to be corrected. - Each time you press the button, the target changes as follows:
Chronograph hour and minute hands → chronograph second hand → date indication → (back to the top)
- Press and release the lower right button
or the upper right button
to adjust the target. - Each time you press button
, the target moves forward by 1 step; each time you press the button
, it move back by 1 step. - They move continuously while you are pressing and holding the button.
- Repeat steps 3 and 4.
- Push the crown in to position
to finish the procedure.
Resetting the watch - All Reset
- Pull the crown out to position
. - Press and release buttons
,
and
at the same time.
All reset is executed and alarm sounds.
After All Reset
After All Reset, adjust the reference position and set the time and calendar.
![]()
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Citizen G910 - Watch Abbreviated Manual
Need help?
Do you have a question about the G910 and is the answer not in the manual?
Questions and answers