Related Manuals for Kernlochbohrer KBS-352/M-PRO
Summary of Contents for Kernlochbohrer KBS-352/M-PRO
- Page 1 Operating instructions Core drill rig KBS-352/M-PRO KBS-502/M-PRO KBS-352/XL-PRO Kernlochbohrer GmbH Geigersbühlweg 52 72663 Großbettlingen Tel. 07022-5034900 E-Mail: info@kernlochbohrer.com Version 0 2. Output 05/2023...
-
Page 2: Table Of Contents
Content Introduction and description About this guide Explanation of symbols Safety regulations Product description Technical data Mounting the drill stand Care and maintenance Maintenance and inspection plan Troubleshooting Exploded view Environmental protection Warranty EC Declaration of Conformity Attachment... -
Page 3: Introduction And Description
Employer's Liability Insurance Association (BG) must be observed. Thanks to the buyer Thank you for purchasing a core drill rig from Kernlochbohrer GmbH. Please read the operating instructions carefully and observe the safety instructions. Through proper operation, you will fully appreciate the outstanding performance of our products. -
Page 4: Safety Regulations
Safety regulations Read all precautions before start-up and keep the operating instructions. ❖ Please follow the operating instructions carefully, as failure to follow these ❖ safety precautions and instructions may cause electric shock, fire and/or serious injury. 1. Keep your work area clean and well lit. Disorder or unlit work areas can lead to accidents. - Page 5 6. Avoid unusual postures. Ensure a secure footing and maintain your balance at all times. Do not work on a ladder. This will give you better control of the power tool in unexpected situations. 7. Wear appropriate clothing. Do not wear loose clothing or jewelry. Keep hair, clothing and gloves away from moving parts.
-
Page 6: Product Description
15. When used for overhead drilling, a functional water collection ring must be used. Make sure that no water can get into the motor. 16. Check all moving and clamped parts before use. 17. Only use original spare parts from Kernlochbohrer GmbH. Product description Drill column... -
Page 7: Technical Data
Technical data Model : KBS-352/M-PRO KBS-502/M-PRO KBS-352/XL-PRO Item number: 6216 6215 6299 Max. Drill size: 402mm 502mm 352mm Drill column: 80x75x1000mm 80x75x1000mm 80x75x2000mm Drilling stroke: 650mm 650mm 1600mm Motor mount: 60mm Mounting bracket 110mm Mounting bracket 60mm Mounting bracket N.W. - Page 8 Warning! In the case of overhead drilling, vacuum attachment to the ceiling is prohibited as it can cause serious injury. To bring the drill stand into the correct position, use the four leveling screws and the level indicator attached to the drill carriage for this purpose.
- Page 9 The KBS-352/M-PRO/KBS-352/XL-PRO and KBS-502/ M-PRO each have a different mounting adapter. The mounting adapter of the KBS-352/M-PRO and KBS-352/ XL-PRO is 60mm while the mounting adapter for the KBS-502/M-PRO is 110mm to allow drilling with larger diameter drills.
- Page 10 The locking device of the drill carriage is located on the top side of the drill carriage. It is intended to prevent the drill sled from falling down and causing possible injury or damage to the drill or the machine. Slide the carriage lock to the left to unlock the carriage, then crank the drill carriage up or down to the desired position and slide the lever lock to the right to lock the drill carriage.
-
Page 11: Care And Maintenance
If you are drilling a wall hole with a stand, first securely fasten the stand to the wall, and only then mount the drill motor on the stand. For the models KBS-352/M-PRO, KBS-502/M-PRO, KBS-352/XL-PRO there are two possibilities of the feed ratio. - Page 12 • In the front area of the drill slide there are 4 rollers. In the rear area there are 4 eccentric clamps. In the course of time, wear may occur on the rollers. If this is the case, tighten the 4 eccentric clamps slightly until the slide can be moved again without play.
-
Page 13: Maintenance And Inspection Plan
Maintenance and inspection plan Regular inspection according to the maintenance and inspection schedule is urgently required. Shorten the intervals between maintenance if you use the product very frequently. every 3rd monthly or annually or Maintenance each time month or after 25 hours after 200 parts before use... -
Page 14: Troubleshooting
Troubleshooting Error Cause Troubleshooting Retighten the 4 the sled wobbles Tensioner worn eccentric clamps. the gear shaft is jammed all 4 rollers worn out Replace all 4 casters. Concentricity of the drive Wear on the gear shaft Replace the worn shaft on the rack or the gear rack part. -
Page 15: Exploded View
Exploded view KBS-352/M-PRO / KBS-352/XL-PRO... - Page 16 Designation Designation anti ntity Spring washer Φ8 Column protection top Washer Φ15xΦ8.6x10 Hexagon socket screw M6x17 Φ8x6 Eccentric shaft Connector rear handle Hexagon socket mushroom head screw Eccentric clamp M6x12 Constant part ring Φ10 Rear handle Weighing plate Rack M1,5x900=L Hexagon socket mushroom head screw Sledge M6x10...
- Page 17 Column mounting Hexagonal lock nut M6 Column block Washer Φ12xΦ6,2x1,5 Hexagonal lock nut M10 Slide lever lock Socket insert Shoulder screw M6x25 Hexagon nut M20xP1.5 T=9 S=30 Key 10x8x100 Motor mounting spacer T=50mm Washer Φ24xΦ10,6x1,5 Hexagon nut M12 Spacer mounting screw M8x35 Leveling screw M12x85 Hand crank Hexagon socket mushroom head screw...
- Page 18 KBS-502/M-PRO...
- Page 19 Description Description Spring washer Φ8 Column protection top Washer Φ15xΦ8.6x10 Hexagon socket screw M6x17 Φ8x6 Eccentric shaft Connector rear handle Eccentric clamp Hexagon socket mushroom head screw M6x12 Constant part ring Φ10 Rear handle Weighing plate Rack M1,5x900=L Sledge Hexagon socket mushroom head screw M6x10 Needle bearing HK152020 Column L=1000mm...
- Page 20 Top sled guard Spring washer Φ8 Hexagon socket mushroom head Base plate screw M5x20 Column mounting Hexagonal lock nut M6 Column block Washer Φ12xΦ6,2x1,5 Hexagonal lock nut M10 Slide lever lock Socket insert Shoulder screw M6x25 Hexagon nut M20xP1.5 T=9 S=30 Key 10x8x100 Motor mounting spacer T=110mm Washer Φ24xΦ10,6x1,5...
-
Page 21: Environmental Protection
Environmental protection Raw material recovery instead of waste disposal! To avoid transport damage, the device must be delivered in sturdy packaging. Packaging as well as device and accessories are made of recyclable materials. The plastic parts of the device are marked according to the material. This enables environmentally compatible, single-variety disposal via the collection facilities offered. - Page 22 Directive 2006/42/EC (identifiable by the CE marking on the power tool) Name and address of the person authorized to compile the technical documentation: Kernlochbohrer GmbH Geigersbühlweg 52 72663 Großbettlingen Location: Großbettlingen Date: 17.05.2023...
Need help?
Do you have a question about the KBS-352/M-PRO and is the answer not in the manual?
Questions and answers