English - HIKVISION DS-2XT6645G0-LIZS/C15 Quick Start Manual

Product appearance is for reference only and may differ
from the actual product.
Interface and Parts Description (Page 2 – A)
Type I: Water-cooling device
Type II: Air-cooling device
Note: The interface varies with the models. Please refer to the
product datasheet for details.
1. RESET
2. DEBUG
3. Memory card slot
4. Power input interface
5. Network interface
6. Alarm interface
7. Audio input interface
8. Audio output interface
Install the Memory Card (Page 2 – B)
Install the Camera (Page 3 – C)
C1. Port Connection
① Air inlet port
② Water outlet port
③ Water inlet port
C2. Wall Mounting
C3. Angle Adjustment
1) Adjust the tilt angle (0° to -45°): Loosen (not unscrew) the six lock
screws in the cardan joint on both sides of the vertical direction
other than the No.1 lock screws. Unscrew the No.1 lock screws and
adjust the camera to the appropriate angle. Tighten the six lock
screws.
2) Adjust the tilt angle (0° to 45°): Loosen (not unscrew) the six lock
screws in the cardan joint on both sides of the vertical direction
other than the No.2 lock screws. Unscrew the No.2 lock screws and
adjust the camera to the appropriate angle. Tighten the six lock
screws.
3) Adjust the pan angle (-45° to 45°): Loosen (not unscrew) the four
No.3 lock screws connected between the bracket and cardan joint,
adjust the camera to the appropriate angle. Tighten the four lock
screws.
C4. Installation Schematic
④ Wiring box
⑤ Air compressor
⑥ Water pump
⑦ Supply air
⑧ Return water
⑨ Supply water
Carefully connect and organize the cables after the installation is
completed. Please connect the power supply for the power-on
self-test of the camera.
 Make sure the camera can be turned on normally and the live
view image can be displayed on the screen.
 If the camera can not be turned on normally, please check
whether the cable interface is connected properly. If the cable
connection is normal, you need to troubleshoot the cable wiring and
so on.
Note:
 The length of the supplied G1/4 and G1/2 pipe is 1 m.
 The dotted line part in the installation schematic should be
prepared and installed by yourself.
 It is necessary to protect the cable from heat when the ambient
temperature of the cable is above 120 °C (248 °F).
 For the water-cooling device, it is recommended to use pure
water for machine circulation. Other fluids may cause safety risks in
high-temperature environments.
Waterproof for Installation (Page 4 – D)
Activate and Access Network Camera (Page 5 – E)
Regulatory Compliance and Safety Information
Read all information and instructions in this document carefully
before using the device and keep it for further reference.
For more device information and instructions, please visit our
website at https://www.hikvision.com. You can also refer to other
documents (if any) accompanying the device or scan the QR code (if
any) on the packaging to get more information.
About this Document
The document includes instructions for using and managing the
product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The
information contained in the document is subject to change,
without notice, due to firmware updates or other reasons. Please
find the latest version in the company website
(https://www.hikvision.com).
Please use this document under the guidance of professionals.
© 2023 Hangzhou Hikvision Digital Technology Co., Ltd. All rights
reserved.
Trademarks
and other Hikvision's trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks
and logos mentioned are the properties of their respective
owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS
MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, ARE PROVIDED "AS IS" AND "WITH
ALL FAULTS AND ERRORS". HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A
PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT
YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,
WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING
NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR
LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET
PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM
CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER
6

English