Advertisement
Quick Links
&e1c1 l rillc1
OWNER
Read this manual carefully before starting assembly. Rea d each step completely b efore b eginning
1.
each step.
2.
Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3.
To make assembly of your basketball system easier, use the Hardware Identifier on page 3
and 4 to identify and sort all fasteners. Check all cartons for kits. All hardware is not
located in one kit.
Do not tighten hardware until instructed to do so. If har d ware is tightene d too soon , mounting
4.
holes may not align an d parts may not easily fit together. Leave locknuts slightly loose until you are
instructe d to tighten them.
5. An electric screw d river is helpful in assem b ly. However, please set at low torque and use caution
b ecause you coul d overtighten the har d ware an d strip the screws.
6.
Save this instruction and your proof of purchase (receipt) in the event that the manufacturer
has to be contacted for replacement parts.
Please Do Not Return This Product To The Store!
Contact MICCA Group customer service department at:
Phone:
1800-551-443
E-mail:
information@goalrilla.com.au
Please visit our W:>rld Wide Web site at: www.Goalrilla.com.au
ON-LINE TROUBLE SHOOTING
ON-LINE PARTS REQUESTS
ADDITIONAL MICCA Group PRODUCT INFORMATION
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128, 8398509
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
The Toughest
Basketball System
on the Planet.
1
Toll
S MANUAL
Free !
&oa l rillct
TECHNICAL ASSISTANCE
FREQUENTIY ASKED QUESTIONS
MODEL NO.
B3333W
&
B3333W-1
CV54
BASKETBALL SYSTEM
2L-7235-04
©2022 Escalade Sports
Advertisement
Related Manuals for ESCALADE GOALRILLA B3333W
Summary of Contents for ESCALADE GOALRILLA B3333W
- Page 1 FREQUENTIY ASKED QUESTIONS ADDITIONAL MICCA Group PRODUCT INFORMATION 2L-7235-04 Escalade® Sports products may be manufactured and/or licensed under the following patents. 6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128, 8398509 ©2022 Escalade Sports Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
-
Page 3: Hardware Identifier
HARDWARE IDENTIFIER 1/2” X 1-1/4” Dia. Plastic-Washer (4 Pieces) / 1 2” -13 x 1” / 1 2” Flat Washer Hex Bolt (2 Pieces) (2 Pieces) Pull Pin (1 Piece) 1/2” Split Lock Washer (2 Pieces) Hardware located in 4A-7081-00 box 1/2”-13 x 9”... - Page 4 HARDWARE IDENTIFIER 3/8” X 19mm Flat Washer (4 pieces) Hardware required for rim assembly 1/2”-13 x 10” 1/2”-13 x 10” 3/8” X 19mm Flat Washer 1/2”-13 X 1 3/4 1/2”-13 X 2 1/4 Hex Bolt (8 pieces) Hex Bolt Hex Bolt Hex Bolt (3 Piece) (3 Piece)
- Page 5 INSTALLATION TIMELINE Prior to anchor system and goal assembly, call utility services for location of underground utility lines before you dig. Vertical main post assembly is a two part process. PART 1 PART 2 Day 1. Complete Anchor System Installation Instructions. Day 5.
- Page 6 GOALRILLA ASSEMBL Y INSTRUCTIONS (Day 5) TOOLS REQUIRED FOR THE FOLLOWING STEPS 1 - 15/16" open end wrench 1 - Level 1 - 15/16” socket and ratchet (optional) 1 - Tape Measure 1 - 9/16” Deep Well Socket & Ratchet 1 - Rubber Mallet 1 - 3/4”...
- Page 7 NOTE: It is important for the installer to understand the NOTE: All board arms are made of rectangular tubing. necessity of the Plastic washers (#5) provided. These Tightening hardware too tight may damage tubing and washers adequately space painted parts at all pivot points. make adjustment of system difficult.
- Page 8 Attach Upper Arms (#6L & 6R) to pole (#2), as shown in F igure 7. Using a bolt (#7), two flatwashers (#3), four plastic washers (#5) and hex nut (#4). Note: Tighten bolts snug but, do not over tighten. Board Arms must pivot freely.
- Page 9 Locate hardware needed to mount pole to anchor bolts. You will need, eight flat washers (#37), four lock washers (#36), four hex nuts (#35) and four thread protectors (#34). NOTE: Do not remove the nuts #35 you installed in step 2 (pg. 5). PLACING THE POST ON THE ANCHOR SYSTEM REQUIRES AT LEAST FOUR CAPABLE ADULTS.
- Page 10 Slide Actuator Handle (#42) onto shaft on the back of Actuator (#16). Line up hole in shaft with hole in Actuator Handle and insert Pull Pin (#41) to secure. Toaid in the assembly of the backboard lower the lower board arm (#11), by turning the Actuator Crank, until the lower arm makes contact with the Safety Stop.
- Page 11 Note: If the Step Bushing (#22) and Board Bushing (#33) are not already pre-installed follow step 15 and 16. Insert a Two Way Step Bushing (#22) in to the inside of bracket on each side of the Backboard (#23) as shown in Detail A.
- Page 12 51 51 Drain Holes must be on bottom Side *Backboard not shown for clarity. Detail C With the help of another adult attach the Cross brace (#52) with four Bolts (#50), eight Washers (#51) and four Nuts (#4) as shown in Figure 12 and Figure 12 Detail C.
- Page 13 INSTALL RIM EXACTLY AS SHOWN. FAILURE TO DO SO COULD DAMAGE GLASS. Mount Goal Assembly (#28) to Backboard as shown in Figure 12, using four bolts (#29), washer (#26) and four nuts (#24). Tighten Note: Make sure (#27) Rim Fasteners but leave loose enough to level rim. Pad is installed between Rim (#28) and Backboard (#23) Place a level across rim assembly and adjust rim until...
- Page 14 Two adults are recommended for this step, one to level and one to adjust the bottom #35 nuts. If further leveling is required loosen top #35 nuts but do not loosen past the top of #39 “J” Bolt. DO NOT REMOVE NUTS #35 Place a level on pole and adjust bottom nuts #35 with a 15/16”...
- Page 15 Raise Backboard to 10 FT. regulation playing height. Measure from top of rim straight down to the playing surface. Using tape - mark the side of the steel actuator (#16) just under the plastic actuator sleeve (#15) at this 10 ft rim height.
-
Page 16: Care And Maintenance
CARE AND MAINTENANCE BACKBOARD CARE AND MAINTENANCE Items needed to clean backboard: 100% cotton soft cloth, (only) Glass cleaner Clean backboard using only a 100% Cotton soft cloth and glass cleaner . Clean glass as you would clean household windows. Strong cleansers will damage backboard and void warranty . -
Page 17: Limited Lifetime Warranty
LIMITED LIFETIME WARRANTY This consumer warranty extends to the original consumer purchase of any MICCA Group Product (hereinafter referred to as the "Product "). WARRANTY C OVERAGE: MICCA Group warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship. - Page 18 B3333W PARTS LIST Key# Part # Description Qty . 3M-8926-00 Pole Pad -Universal 1A-6994-00 Post Assembly 2B-6093-10 1/2” Flat Washer 2B-6242-10 1/2-13 Nylon Locknut 3M-6245-01 1/2” X 1-1/4” Plastic Washer 1A-7674-01 Upper Board Arm (Right Hand) 1A-7675-01 Upper Board Arm (Left Hand) 1B-6787-10 1/2-13 X 9 "...
- Page 19 Left Right 2L-7248-04...
Need help?
Do you have a question about the GOALRILLA B3333W and is the answer not in the manual?
Questions and answers