Controls & Display; Getting Started - Levoit LAP-V201S-AEUR Manual

EN
C O N T R O L S & D I S P L AY
You can also use the VeSync app to control these functions, as well as additional app-only features
Note:
(see page "VeSync App Functions" on page 7).
Auto Mode Button
Turns Auto Mode on (see page 5).
•
Sleep Mode Button
Turns Sleep Mode on (see page 5).
•
Press and hold for 3 seconds to
•
reset the Check Filter Indicator.
Check Filter Indicator
Lights up red when the filter should
•
be checked (see Check Filter
Indicator, page 8).
To reset the Check Filter Indicator,
•
press and hold
The Check Filter Indicator will flash
3 times, and turn off.
Fan Speed Button & Indicators
Cycles through fan speeds: low (1
•
indicator will light up), medium (2
indicators), high (3 indicators), and
turbo (4 indicators).
Tapping
•
in Auto Mode, Sleep Mode, or Pet
Mode (when the display is lit up)
will exit that mode.
Air Quality Indicator
These indicator rings use an
•
automatic infrared dust sensor to
display the air quality: Blue (Very
Good), Green (Good), Orange
(Moderate), Red (Bad).
On/Off Button
Turns the air purifier on/off.
•
Press and hold for 5 seconds to
•
connect the air purifier to the VeSync
app. See the in-app instructions for
more information (see page 5).
Press and hold for 15 seconds to
•
reset the air purifier and disconnect
from Wi-Fi® (see page 5).
Wi-Fi Indicator
Blinks when connecting to the
•
VeSync app, lights up when
connected to VeSync, and is off
when disconnected from VeSync.
See the VeSync in-app instructions
for more information (see page 5).
Timer Button & Indicators
Cycles through timer options: 2 hours,
•
4 hours, and 8 hours (see page 6).
Note:
with the corresponding timer selected.
•
is used through the VeSync app.
4
for 3 seconds.
while the air purifier is
The timer indicators will light up
lights up when the timer function
Display Lock Button & Indicator
Prevents current settings from
•
being changed (see page 6). Press
and hold for 3 seconds to lock and
unlock the display.
Display Lock can also be
Note:
controlled through the VeSync app.
The Display Lock Indicator will light up
•
when the display is locked and blink
when any other button is tapped to
indicate the display is locked.
Pet Mode Button
Turns Pet Mode on (see page 6).
•
Light Sensor
The Light Sensor detects the amount
•
of light in the room to automatically
adjust the air purifier settings (see
Light Detection, page 6).
Light Detection can be turned on/off
•
in the VeSync app (see page 6).
G E T T I N G S TA R T E D
Place the air purifier on a flat, stable surface
1.
such as the floor.
Pull both sides of the front cover to remove it.
2.
[Figure 2.1]
Push the pre-filter's tabs inward and pull to
3.
remove the pre-filter from the air purifier.
[Figure 2.2]
Remove the True HEPA / Activated Carbon
4.
Filter from inside the air purifier.
Remove the plastic packaging from the filter
5.
and place the filter and the pre-filter back into
the air purifier. [Figure 2.3]
Make sure the True HEPA filter (the side with
Note:
the ribbon handle) is facing outward when you
[Figure 2.4]
insert the filter.
Place the front cover on the air purifier. Make
6.
sure to align the tabs on the cover with the slots
on the bottom of the air purifier. [Figure 2.5]
Insert the power adapter plug into the back of
7.
the air purifier. [Figure 2.6]
When using the air purifier, allow at least 15
8.
inches / 38 cm of clearance from the front of the
air purifier. Keep away from anything that would
block air flow, such as curtains. [Figure 2.7]