Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Worx Nitro Sonicrafter WX693
Summary of Contents for Worx Nitro Sonicrafter WX693
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS Oscillating Tool WX693 WX693.X...
- Page 2 PRODUCT SAFETY the influence of drugs, alcohol or medication. A moment of inattention while operating power GENERAL POWER TOOL tools may result in serious personal injury. b) Use personal protective equipment. Always SAFETY WARNINGS wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard WARNING Read all safety warnings, hat, or hearing protection used for appropriate instructions, illustrations and specifications...
-
Page 3: Safety Warnings For Battery Pack
SAFETY INSTRUCTION FOR damaged, have the power tool repaired before use. Many accidents are caused by poorly CUTTING maintained power tools. f) Keep cutting tools sharp and clean. Properly Hold power tool by insulated gripping surfaces, maintained cutting tools with sharp cutting edges when performing an operation where the cutting are less likely to bind and are easier to control. - Page 4 q) Do not mix cells of different manufacture, capacity, size or type within a device. Avoid danger of injury from the r) Keep the battery away from microwaves and sharp edges of the accessories. high pressure. Accessories can become very hot SYMBOLS while working, presenting danger of burns!
- Page 5 Oscillating Tool WX693 WX693.X...
- Page 6 O F F - - - - - - Oscillating Tool WX693 WX693.X...
-
Page 7: Component List
COMPONENT LIST SUGGESTED BATTERIES AND CHARGERS HYPERLOCK™ ACCESSORY CLAMPING LEVER Category Model Capacity ON/OFF SWITCH WA3550 1.5Ah VARIABLE SPEED DIAL WA3550.1 1.5Ah VENTING SLOTS 20V Battery WA3551 2.0Ah UNIVERSAL-FIT™ ACCESSORY INTERFACE* WA3551.1 2.0Ah SMALLER FLANGE (FOR OTHER BRANDS’ SANDING PADS) WA3553 4.0Ah FLANGE... - Page 8 used: Remove or install battery pack See Fig. G How the tool is used and the materials being cut or drilled. LED Light See Fig. H The tool being in good condition and well maintained. The Variable Speed Dial can be used to set the The use of the correct accessory for the tool and optimum oscillating frequency according to the ensuring it is sharp and in good condition.
- Page 9 APPLICATION WARNING: The sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before the operation. Description Application Wood, plastic, fiberglass, nails, non- Universal Metal/Wood End Cut ferrous metals, thin sheet metal, Blade hardened fillers Standard Wood End Cut Blade...
-
Page 10: Environmental Protection
FOR BATTERY TOOLS: the tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice. The ambient temperature range for tool and battery use and storage is 0 C-45 NOTE: When plunging and sawing use a slight The recommended ambient temperature range for the pendulum motion, to allow sufficient chip removal. -
Page 11: Declaration Of Conformity
DECLARATION OF CONFORMITY Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany On behalf of Positec declare that the product, Description WorxNITRO Sonicrafter ® Type WX693 WX693.X (6-designation of machinery, representative of high frequency oscillation tool) Function Sanding, sawing, rasping, scraping, polishing Complies with the following Directives, 2006/42/EC 2014/30/EU... - Page 12 DECLARATION OF CONFORMITY Positec (UK & Ireland) Ltd., PO Box 6242, Newbury, RG14 9LT, UK On behalf of Positec declare that the product, Description WorxNITRO Sonicrafter ® Type WX693 WX693.X (6-designation of machinery, representative of high frequency oscillation tool) Function Sanding, sawing, rasping, scraping, polishing Complies with the following regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016...
Need help?
Do you have a question about the Sonicrafter WX693 and is the answer not in the manual?
Questions and answers