Table of Contents
Advertisement
CONNECTING THE PROJECTOR
COMPUTER INPUT TERMINAL
Connect the computer output
to this terminal.
(Refer to P12 ~15.)
CONTROL PORT CONNECTOR
When controlling the computer
with the Remote Control of this
projector, connect the mouse
port to this connector.
(Refer to P12 ~15.)
COMPUTER AUDIO INPUT JACK
Connect the audio output from
the computer to this jack.
(Refer to P12 ~15.)
AUDIO INPUT JACKS
Connect the audio outputs
from the video equipment
to these jacks.
(Refer to P11.)
When the audio output is
monaural, connect it to
the AUDIO LEFT jack.
COMPUTER INPUT / MONITOR OUTPUT TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of the
computer to this COMPUTER INPUT with the
VGA Cable (supplied), and connect the monitor
to this MONITOR OUTPUT with the monitor
cable (not supplied). When connecting the
Macintosh computer, the MAC/VGA Adapter is
required (not supplied).
CONTROL PORT CONNECTOR
Terminal : MULTI-POLE 12-PIN
When controlling the computer with the
projector's Wireless Remote Control Unit,
connect control port (PS/2, Serial or ADB port)
on your computer to this connector. (Control
Cable for PS/2 Port is supplied.)
SERIAL PORT CONNECTOR
Terminal : DIN 8-PIN
This connector is used to connect a computer
to control the projector with the PC. For this
connection, the Serial Cable is required (This
cable is not supplied).
10
TERMINALS OF THE PROJECTOR
COMPUTER IN
CONTROL PORT
R–AUDIO–L
(MONO)
VIDEO INPUT JACK
Connect
the
video
output from the video
equipment to this jack.
(Refer to P11.)
Pin Configuration
Pin Configuration
2
6
5
10
9
12
Pin Configuration
8 7 6
5
2
MONITOR OUT
SERIAL
AUDIO IN
AUDIO OUT
S-VIDEO
▼
VIDEO
S-VIDEO INPUT JACK
Connect the S-VIDEO
output from the video
equipment to this jack.
(Refer to P11.)
5
4
3
2
1
10
9
8
7
6
15
14
13
12
11
1
4
3
8
7
11
4
3
1
MONITOR OUTPUT TERMINAL
Connect to the monitor to this
terminal.
(Refer to P12 ~15.)
SERIAL PORT CONNECTOR
This connector is used to
connect a computer to control
this projector with the PC.
(Refer to P12 ~13.)
AUDIO OUTPUT JACK
Connect the audio amplifier to
this jack.
(Refer to P12 ~15.)
RESET BUTTON
This projector uses a micro
processor to control the unit.
Occasionally,
the
processor may malfunction and
need to be reset. This can be
done by pressing the RESET
button with a pen, which will
shut down the unit. Turn the
projector off and restart the unit.
Do not use the RESET function
excessively.
1
Red Input
9
Non Connect
2
Green Input
10
Ground (Vert.sync.)
3
Blue Input
11
4
Sense 2
12
5
Ground (Horiz.sync.)
13
Horiz. sync.
6
Ground (Red)
14
Vert. sync.
7
Ground (Green)
15
Reserved
8
Ground (Blue)
PS/2
Serial
ADB
-----
-----
1
T X D
-----
2
CLK
ADB
3
-----
-----
DATA
-----
-----
-----
4
5
-----
-----
R X D
-----
-----
-----
6
-----
-----
7
READY
8
-----
-----
-----
9
GND
GND
GND
10
-----
-----
-----
-----
-----
-----
11
-----
-----
-----
12
1
R x D
5
2
ADB
6
3
MUX232
7
4
GND
8
micro
Sense 0
Sense 1
MUXTTL
T x D
–––––
–––––
Advertisement
Table of Contents
