Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datapath VisionSC-SDI4
Summary of Contents for Datapath VisionSC-SDI4
- Page 1 VisionSC-SDI4 User Guide Version 1.0.4...
-
Page 2: Table Of Contents
Contents Safety Instructions............................1 FCC Statement...............................2 Introduction................................3 Hardware Overview.............................4 Software Overview............................5 Specification..............................7 Unpacking................................8 Installing the Capture Card........................9 Installing Multiple Cards..........................10 Firmware Upgrades ..........................11 Software Installation..........................12 Datapath Limited............................13 Index..................................14... -
Page 3: Safety Instructions
These ento el equipo, a fin de evitar daños en su producto de Datapath o lesiones al personal instructions should be made available to all those who will use and operate Datapath encargado de su manejo. -
Page 4: Fcc Statement
FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limit are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause harmful interference to radio communications. -
Page 5: Introduction
AV professionals looking to capture from multiple sources. Ideal for use in broadcast markets or with any SDI capable applications the VisionSC-SDI4 provides four 3G-SDI inputs each capable of capturing 1920x1080p @ 60 frames per second (fps). Each capture channel is hardware time stamped allowing for larger surfaces to be captured and stitched together. -
Page 6: Hardware Overview
Single PCIe endpoint, allowing for more cards & captures to be placed within a single system. Datapath Vision Performance Driver Multiple cards per system, 16 streams per card Frame sync and time stamping Automatic signal detection Direct Show interface Datapath RGBEasy API Models VisionSC-SDI4 - 3G-SDI Video Capture Card Fig. 1 Fig. 2... -
Page 7: Software Overview
User Mode filter for source selection • Enables cropping support in DirectShow on all inputs • Supports Start and Stop trigger interface on all Visi0n inputs Datapath Unified Vision Driver • Multiple cards per system, 16 streams per card • Frame sync and time stamping... - Page 8 • The RGBEasy API for advanced audio and video control • Fully integrated for use with Datapath Wall Control software for video wall applications Multistream Datapath’s MultiStream feature is available on all Datapath capture cards and enables multiple independently formatted video streams to be setup in parallel.
-
Page 9: Specification
Specification Board Format PCI-Express x8 plug-in card, 110mm x 177mm (incl heat sync) Connectors (main board) 4 BNC Connectors Maximum Capture 2.97Gbps capture bandwidth per channel. Resolution Provides => 4 * 1920 x 1080p @ 60Hz. Frame Buffer 768MB Input Mode Detection Supports SMPTE - 352 Payload Identifiers Sample Formats RGB: 4-4-4 (+A) -
Page 10: Unpacking
It is recommended that you do not discard the packing box until you are completely satisfied with the VisionSC-SDI4 capture card and it is fully installed and working correctly. We also recommend that you make a note of the serial number of the card in a prominent place before the card is plugged into the computer. -
Page 11: Installing The Capture Card
BNC cable becoming separated from the card and the connection being lost. Cable Lengths The VisionSC-SDI4 supports cable lengths of up to 150m for 3G-SDI. This figure is based on using low loss coax cables (Belden 1694A). Avoid tight loops or kinks in the cables. -
Page 12: Installing Multiple Cards
In order to control the order in which the driver uses the cards, it is recommended when installing multiple cards that the links on the VisionSC-SDI4 are configured. The example below shows the jumper link settings for up to 32 cards in a single system. When two cards share the same link settings, their order is determined by the PCIe bus. -
Page 13: Firmware Upgrades
Datapath. Whenever a firmware upgrade is performed, the SW2 on the DIP switch must be set ON. The DIP Switch can be located on the back of the VisionSC-SDI4 (See Fig. 6 ). To perform the upgrade, follow the step-by-step instructions provided by the upgrade application. The VisionSC-SDI4 is shipped with the SW2 switch set at ON, therefore no action should be necessary. -
Page 14: Software Installation
The help file must be located on the local machine to view its content. Using the card with other Datapath products The VisionSC-SDI4 captures data and stores it in an on-board video buffer. This data is then copied using DMA to the host system for display, storage or streaming. -
Page 15: Datapath Limited
Datapath Limited Datapath has a long and very successful history in the computer graphics industry. Datapath has been designing and supplying high performance, high quality graphics display systems to the world’s larg- est and most demanding companies and institutions since 1982. Datapath was one of the founding companies of multi-screen Windows acceleration using single and multi board solutions. -
Page 16: Index
Packing box 8 Cable Lengths 9 Power Requirements 7 Connecting BNC cables 9 Copyright Statement 13 RGBEasy API 4 Datapath CD 12 Software Capabilities 5 Datapath Limited 13 Software updates 12 DIP switch 11 Supported Frame Rates 7 Direct3D 12...
Need help?
Do you have a question about the VisionSC-SDI4 and is the answer not in the manual?
Questions and answers